Parker ORIGA P120 Series User manual

Assembly Instructions: Series P120, Series P210, and Series 2000

2
A
ssembly Instructions
Series 2000 and Series P210
Ø16
Series P120
Ø40-80mm
Ø10mm

3
Assembly Instructions (Series P120, Series P210, Series 2000)
Series P210 and Series 2000

Assembly Instructions
4

Assembly Instructions
5

6
THE NEW REVISED 2000 RODLESS VERSION
In the spirit of continuous improvement, Parker ORIGA Corporation has upgraded its 2000 series Rodless
cylinder. Current customers needing the old version 2000 repaired, rebuilt or remanufactured will need the
following information. The following are answers to some anticipated questions:
How do I distinguish the old 2000 from the revised 2000 version? Or how do I know if I already have the
revised version?
The most obvious distinguishing feature of the revised 2000 is its newly shaped outer band lock (item 25),
which is fastened by one flat head screw. See Figures 1 & 3.
If you don’t see this distinguishing feature, then you have the old 2000 series or the P120 series (with the
round barrel).
Did the envelope dimensions change in the NR20 mount (standard mount)?
The critical envelope dimensions did not change such as overall length, bolt hole patterns, thread sizes
and depths, end cap square, etc. The “J” dimension of the 32mm, 40mm and 50mm did change to 6.69,
6.69 and 9.06 respectively. See figure 2. The piston mounting holes did not change. We are confident that
most of the changeovers to the revised 2000 will be painless. Nevertheless, if there is a concern, we would
be more than happy to listen and accommodate your customer’s needs.
FIGURE 1
Item 25

Were there any changes to the dimensions for the piston mounts NR25, NR30 and NR35?
The catalog dimensions did not change.
Were there any changes to the dimensions for the cylinder mounts NR4, NR7 and NR8?
The catalog dimensions did not change.
Did the maximum loads and maximum moments change as reflected in the catalog?
No, they did not.
Will the Clean Room, Joint Clamp, Double Piston, NR50 and Powerguide cylinders still be available with
this revised 2000 cylinder?
The Clean Room, Double Piston and Joint Clamp cylinders will still be offered.
The NR50 and the Powerguide will be phased out from the 2000 series effective immediately. The
alternative offering is in our OSP-P cylinder line with the Slideline (NR-50) OSP-P and the Powerslide
(Powerguide) OSP-P. As with the standard base cylinders, the critical dimensions haven’t changed. You can
compare the dimensions in the catalogs for the details.
What parts were not affected by the revision?
Those parts are the inner band (item 3), the barrel (item 1) and its magnet (item 2). See Figure 3.
7
FIGURE 2

8
25 21 20 24
18
15 16 8
9
14A
13
11 10 7
4
3
2
1
27
22
19
17
23
26 28
12
5
6
29
14B
FIGURE 3
NOTE: FOR 25mm ONLY, ITEMS 23, 26 & 28 ARE AN
INTEGRAL PART OF THE CAP (ITEMS 17 & 18)

UPGRADE KITS
How do I rebuild my old 2000 series cylinder and at the same time upgrade it to the 2000-revised version?
An “Upgrade Kit” will now be required to repair a Series 2000 cylinder out in the field.
An “Upgrade Kit” will consist of a piston assembly, end cap assembly, piston mount assembly and
service pack.
Order No. — Bore–Upgrade–Stroke–B(Buna)–V(Viton)
32-2020/20x15-BM
32-UPGRADE-15-B
Once the cylinder has been upgraded to a Revised 2000 Series, just a service pack or seal kit can be
ordered in the future (see new part numbers on page 18).
9

10
Did the switches (Hall Effect and Reed) change?
Yes, it did. The switches used on the revised 2000 cylinders will now be the same switches that are used in
our OSP-P line of cylinders. It’s worth noting that these switches are more compact. See Figure 4 on how
this switch is attached to the barrel.
Tightening the set screw (hidden)
will lock switch in place
FIGURE 4