Paslode TrimMaster IM250A-Li User manual

IMPORTANT!
DO NOT DESTROY
It is the customer's responsibility to have
all operators and service personnel read
and understand this manual.
OPERATING MANUAL
Part No. 902400
Model IM250A Li
CORDLESS 16 GAUGE
ANGLED LITHIUM-ION
FINISH NAILER

Introduction
For ease of use, this manual is divided into sections (see
Contents). Each section of the manual is written with you,
the tool operator, in mind. We have left out many of the
technicaltermssothatyoucaneasilyunderstandhowtoget
themaximumperformancefromyourCordlessFinishNailer,
andhowtoavoiddamagingthetoolorinjuringyourself.But,
to accomplish this, we need you to do two things:
1.READTHE MANUAL FROM COVERTO COVER
BEFORE USINGTHETOOL.
2.FOLLOW ALL INSTRUCTIONS INTHE MANUAL.
The Cordless Finish Nailer should be handled like other
powerfasteningtoolsthatyouuse.Likemosttools,when
used improperly injury could result . If you are going to
allow others to use the Cordless Finish Nailer, it is your
responsibilitytomakesurethattheyalsoreadandcomply
with the instructions in this manual before attempting to
operate the tool.
This manual is intended to acquaint you with the Paslode
Cordless 16 ga. Angled Lithium-ion Finish Nailer. Unlike
other power fastening tools, the Cordless Finish Nailer is
powered by an internal combustion linear motor. In simpler
terms, your Cordless Finish Nailer is powered by a motor
similar to the one that powers an automobile. The Cord-
less Finish Nailer ignites a fuel and air mixture to produce
the energy to drive the motor, which in turn drives the
fastener. The Cordless Finish Nailer is totally
self-contained. It carries its own fuel supply and battery,
along with a supply of fasteners.
Paslode Cordless 16 Gauge Angled
Lithium-ion Finish Nailer Operating
Manual

Description
Inorderforyoutofullyunderstandtheinformationcontained
in this manual, you need a basic understanding of the
Cordless Finish Nailer. As you can see in the illustration
below,the Cordless FinishNailer ismadeup of threemajor
areas: handle, motor, and magazine.
AsyouexaminetheCordlessFinishNailer,becomefamiliar
with the three major areas and the various components
located in each of them.
The Handle Assembly containsthe fuel cartridge, indicator
light, and the trigger.
TheMotorAssemblycontainsthecoverandfilter,themotor
housing, the nose, and the work contacting element.
TheMagazineAssembly daolotstnenopmocehtsniatnoc
and control the fastener and the battery for the Cordless
Finish Nailer.
Specifications
Dimensions: Weight-with battery 4 .6 lbs
Height 11-1/2 inches
Length 10-3/4 inches
Magazine Angled
(use Paslode angled fasteners only.)
Cycle Rate: Intermittent Operation – 2 to 3 nails
per second
NOTE: Exceeding these cycle rates could cause the tool
to overheat, resulting in loss of performance or damage to
tool components.
Fasteners: 16 Gauge Angled
Magazine
Capacity: 2 nail strips, or 100 fasteners.
Battery : 7.4voltsDC-
Provides enough energy to
drive approximately 6000 fasteners on a
full charge.
Fuel
Cartridge:
Trim fuel cartridge (.64oz) Part #816007
Liquid hydrocarbon - Provides enough fuel
to drive approximately 1000 fasteners.
Magazine Assembly
fuel cartridge compartment
cap
removable
grille & filter
no-mar tip
Handle Assembly
(soft grip)
soft
touch
trigger
Motor
Assembly
battery compartment
(opposite side)
battery indicator light
(opposite side)
follower
motor housing
nail count indicator
lockout
feature
adjustable
depth of drive
(opposite side)
quick clear
cover
rafter/belt hook
The Paslode Cordless 16 ga. Angled Lithium-ion Finish
Nailer is a self-contained, fully portable nailer that uses
liquid hydrocarbon fuel to power a unique linear drive
internal combustion motor.
Overview of the Paslode Cordless
16 Gauge Angled Lithium-ion Finish Nailer
By using the Paslode Cordless 16 ga. Angled Lithium-ion
Finish Nailer at its recommended cycle rate, you will be
able to drive several thousand nails in a typical workday.

Safety Instructions
DANGER
WARNING
WARNING
Do not expose the tool to
temperaturesinexcessof
120° F (49° C). Fuel and/
or the battery may burst,
releasing flammable gas.
WARNING
WARNING
The following safety instructions have been included in
this booklet to provide you with basic information neces-
sary for safe operation of the Paslode Cordless 16 ga.
Angled Lithium-ion Finish Nailer.
DO NOT ATTEMPT TO OPERATE THIS TOOL UNTIL
YOU HAVE READ AND UNDERSTAND ALL SAFETY
PRECAUTIONS AND MANUAL INSTRUCTIONS.
The Cordless Finish Nailer
is an internal combustion
device. It produces hot
exhaust gases that may
ignite flammable materials.
This tool must not be used
in a combustible environ-
ment or in the presence of
combustible materials,
such as flammable chemi-
cals, adhesives, gasoline,
or solvents.
Do not attempt to operate
this tool until you have read
and understood all safety
precautions and manual
instructions.
Failure to follow all safety
precautions and instruc-
tions may result in a perma-
nent loss of vision, serious
personal or even fatal
injury, property damage
and/or tool damage.
This tool must be operated
only in a well-ventilated
environment, because
the tool exhausts carbon
monoxide similar to a gas
chainsaw or lawnmower.
Exposure to carbon mon-
oxide may cause dizzi-
ness, nausea, or uncon-
sciousness.
ALWAYS keep the Cordless
Finish Nailer, fuel cartridge,
battery and battery charger
out of the reach of children.

Safety Instructions
WARNING 7. NEVER OPERATE THE TOOL WITH THE
WORK CONTACTING ELEMENT REMOVED OR
DISABLED.
This device helps reduce the possibility of accidental
fastenerdischargebypreventingthetoolfromoperating
until it is completely against the work surface.
NEVER operate the tool if the work contacting element
is not working properly.
8.
Pull the follower slightly back and push the release
lever.Tipthe tool noseupslightlyand fasteners should
slide out of the rear of the magazine. If fasteners are
jammed, refer to the appropriate servicing section of
this manual.
9. NEVEROPERATETHECORDLESSFINISH NAILER
IF PARTS ARE LOOSE, DAMAGED OR MISSING.
10. DO NOT DRIVE FASTENERS INTO KNOTS OR ON
TOP OF OTHER FASTENERS.
A fastener may ricochet and cause serious injury.
11. OPERATE THE TOOL ONLY ON THE WORKPIECE.
1. Eye protection must meet the requirements of ANSI
Standard Z87.1 and should have side shields for
increased protection.
2. NEVER ASSUME THE TOOL IS EMPTY.
Never point the tool at yourself or anyone else.
3. NEVER ENGAGE IN "HORSEPLAY" WITH THE
TOOL.
The Cordless Finish Nailer is not a toy – it is a tool.
Careless and improper use may result in a serious
accident.
4. NEVERCARRYTHETOOLWITHYOURFINGERON,
OR SQUEEZING, THE TRIGGER.
This practice may result in the accidental discharge of
a fastener.
5. NEVER OPERATE A MALFUNCTIONING TOOL.
Refer to the servicing or troubleshooting section of this
manual to correct the problem. If the problem cannot
be corrected, stop using the tool and report it to your
supervisor or Paslode®representative.
6. DO NOT LOAD FASTENERS WITH THE TRIGGER
AND/ORWORKCONTACTINGELEMENTPRESSED
IN.
A fastener may be accidentally discharged.
WARNING
TheCordlessFinishNailer
should be operated only
when it is in contact with
the work surface. When
fastening thin materials
such as plywood, be sure
toposition the toolsothat
the fastener is driven into
the underlying piece.
ALWAYS POINT THE TOOL AWAY FROM YOUR-
SELF AND OTHERS WHEN CLEARING A JAM OR
REMOVING FASTENERS.
Always wear EYE and EAR
safety gear when working
with or in the vicinity of the
Paslode Cordless 16 ga.
Angled Lithium-ion Finish
Nailer.

Safety Instructions
12. NEVER DRIVE FASTENERS INTO AREAS WITH
CONCEALED HAZARDS.
Always check the area behind the work surface for
electrical wiring, gas pipes, water pipes, sewer drains
or other potential hazards.
13. ALWAYSMAINTAINSECUREANDUNOBSTRUCTED
FOOTING WHEN ON LADDERS, PLATFORMS OR
OTHER HIGH LOCATIONS.
14.ALLOWONLYQUALIFIEDPERSONNELTOOPERATE
THE CORDLESS FINISH NAILER.
15. PROPERLY STORE FUEL CELL.
16.ALWAYSSTORETHETOOLWITHTHEFUEL
CARTRIDGE AND BATTERY REMOVED.
17. KEEP THE TOOL CLEAN.
A clean tool is less likely to jam or malfunction.
18. KEEP YOUR HANDS CLEAR OF THE WORK AREA
SURFACE.
WARNING
Never over-reach, since
tool recoil may cause a
loss of balance. Always
dnasegdefoerawaeb
drop-offs when nailing on
rooftops and other high
locations. Keep them in
full view.
WARNING
Only persons who have
readandfullyunderstand
all tool operation, safety
and maintenance
instructions should be
allowed to operate the
tool.
WARNING
A fastener may exit at an
angle unexpectedly and
cause injury.
WARNING
Battery Disposal:
IMPORTANT SAFETY INSTRUCTIONS!
SAVETHESE INSTRUCTIONS!
DANGER
TO REDUCE THE RISK OF FIRE OR
ELECTRIC SHOCK, CAREFULLY
FOLLOW THESE INSTRUCTIONS
CHARGING SYSTEM SAFETY
INSTRUCTIONS!
The Paslode batteries contain lithium and should be
recycled or disposed of properly. It is illegal in some
areas to place a lithium battery into the trash or solid
waste stream.
Always store fuel cartridges
where they will not be
exposed to an open flame,
sparks or temperatures
above 120° F (49° C).
Store the fuel cartridge in the case with the cordless
finish nailer
For connection to a supply outside North
America, use an attachment plug adapter
of the proper configuration for the power
outlet, if needed.

Warning
CHEMICAL/EXPLOSION
HAZARD
Read ALL instructions be-
fore charging or using bat-
tery. Failure to follow ALL
instructions may result in
fire, severe burns, or re-
lease of toxic materials.
Battery and Charging System
Charging Instructions
1.
2. Remove the battery from tool or case and insert ter-
minals down into charger. The red light will come on
indicating that the battery is charging and the green
light will go out.
3. After charging is complete, the red light will go out
and the green light will come on, indicating that the
battery is fully charged. The charger will keep the
battery at full charge until it is removed.
4. Unplug the charger from the 120V AC outlet.
CHARGINGTIMES:
First charge (new battery) 1 hour
Discharged Battery 5 minutes to 1 hour
CHARGING DON'TS:
1. Do not charge battery outdoors or in temperatures
below 40°F (5°C).
2. Do not allow metal objects to come in contact with
battery terminals.
3. Do not puncture or attempt to open battery case or
cells.
4. Do not store battery where it will be subjected to
temperatures above 120°F (49°C).
5. Do not incinerate battery.
6. Do not use a defective battery charger, one that
over-heats and/or smokes when plugged in.
7. Do not immerse the battery or charger in water.
Charging System Accessories:
Battery Charger - Part No. 902672
Note
Battery and Charging System
Important Charging Notes
Removethe charger unit from the tool case and plug
it into a 120V AC outlet. Set the charger base on a
stable surface. A green light will come on to indicate
the power is on and the charger circuit is ready.
If battery is completely discharged, the red light and
the green light may alternate back and forth for up to
20 minutes. This safety feature slowly recharges the
battery until it is ready to accept the full charging
current. If the red and green lights continue to alter-
nate after 20 minutes, replace the battery.
The Paslode Cordless 16 Gauge Angled Lithium-ion
Finish Nailer comes with a rechargeable battery and
its own charging system. This charging system is
the only one that will work with the Paslode
lithium-ion batteries. The first step in preparing a
new tool for operation is to fully charge the battery.
New batteries are shipped partially discharged
and must be charged prior to first use. Batteries
will take 5 minutes to 1 hour (time will be dependant
on the amount of discharge of the battery) to
recharge.
6ft. Cord
Battery
Charger
THE PASLODE BATTERY CHARGING SYSTEM

Battery and Charging System
Inserting Battery
1. hsiniFsseldroCehtotni,tsrfistcatnoc,yrettabehtdaoL
Nailer.
2. Push battery fully forward into its locked Ready
position. The battery indicator light will light.
3.
NOTE: If battery is left in tool for an extended period,
the battery will discharge completely and will require
recharging.
Battery Indicator Light
Ontherightsideofthehandleisasmallplasticlens. Thisis
the battery indicator light. When you insert a fully-charged
battery into the tool, you will see a blinking green light. If
the indicator light blinks red, recharge the battery.
BATTERY INDICATOR LIGHT
CAR ONMOOXI E HZARD SON Y N E T A ED R A O VO DA S A ND UN ON CUNESS
ESINUEE T E MDD EPOL UN N R P C P U EN A N R EACETS
! XLO I NH Z RD E ERU E N E LO IV A MO H RE OOLE H U T OULD G T F MES
T L P TR N B S A D R MUTW R E E ND E R NG POTE T N T A COF RMS O ANSS AND R S
A OL S G AL M A LRU ER IS
! S UM T OLI A WA SOADDANDW LL A W YS RA F SN R
R D MANU L R M OV R OCO ER DI E ARD N WA N N S OLD R SLTI A C D NS
C R O MO O IDE A A D SEON Y IN E TI A E A EA O VO D NA S A ND N ON C U NESS
E SO N US E T L ODE D MPLO L UR N NR P C P U E TANRE A CE TS
E P O ON A A D E E U E N XL S V A MO H RE OOL H US OUL GTE U ES
T OP R T RA DB STAD RS MU T WE R EYE ND HE R G P O ET NT A CO F RMS OANS S AND R S
T D L S I A L M AL OC R R U S R IS
!AS U E OO IS A W YS O D D A D W L AW YS RA F S NER
EAD MNUALOM OVER OO ER I E A D N WAN N S O LD S LT I A C D NS
4.
To remove battery, push down on locking tab and slide
battery out.
To disengage the battery, push down on locking
tab and slide battery back until it locks into the
Standby position.
Ready
Position
Standby
Position

DANGER
EX PLO SIO N/FI R E
HAZARD
WARNING
Sunlight can raise the inside temperature of an
unventilated car or van to above 140°F (60°C).
Never puncture or attempt to open the fuel cartridge;
it is non-refillable.
Never incinerate, reclaim or recycle the fuel cartridge.
Neversmokewhileinstalling the fuel cartridge.
Never inhale the spray.
Keep out of the reach of children.
Store fuel cartridge(s) in well-ventilated areas only.
Fuel Cartridge
Toejectthefuel,propellantpressuresqueezestheinnerfuel
container, much as you squeeze a tube of toothpaste. This
squeezing action ensures that all the fuel is used, and that
the Cordless Finish Nailer can operate in any position.
Because of this container-within-a-container design, you
might hear the sound of fluid when shaking the fuel cell
afterallthefuelhasbeenused.Thisisthepropellant,which
remains between the containers even after all the fuel has
been expelled.
Fuel Cartridge
NOTE
1. When replacing fuel cartridge also clean or replace
the air filter for optimum tool operation.
PaslodeCordlesstechnologyispoweredbyaninternal
combustionengineandareeffectedbyaltitude. The
toolmaylosepowerorbecomeerraticatelevationsof
.
NOTE: Altitude Restriction
6000 feet or greater.
There is a second container inside the fuel cartridge. The
inner container holds the fuel. The space between the
inner container and the outer cylinder is filled with a gas,
called the propellant, which is under pressure.
Read ALL safety
instructions before using
or handling the fuel
cartridge. Failure to
follow ALL instructions
may result in explosion or
fire. This may cause
severe personal injuries
or property damage.
Keep the fuel cartridge
away from heat, sparks
and open flame.
Exposure to tempera-
tures above 120°F
(49°C) may cause the
fuel cartridge to burst,
releasing flammable
gas.
If you expose the empty fuel cartridge to extreme
temperatures, the propellant gas will expand and could
cause the container to burst, releasing flammable gases.

Fuel Cartridge
NOTE:
Paslode Cordless fuel cartridges are marked with a “Best Use Before” date on the bottom of the can.
For maximum performance use fuel before the“Best Use Before” date.
DANGER
Paslode Cordless Fuel Cartridges are flammable.
Do not remove fuel cartridge cap or install on other
fuel cartridges!
Paslode Cordless Fuel Cell/Cartridge Disposal Guidelines
Paslode the industry leader in cordless technology provides this information to assist users with the proper disposal of discarded
fuel cells/cartridges. Acceptable disposal options vary depending on the type of fuel cell/cartridge users. All users must cons ider
federal, state and local solid waste regulations to ensure that discarded fuel cells/cartridges are disposed of properly. Users must
contact their local solid waste authority for further guidance.
Discarded fuel cells/cartridges (used or unused) may be considered hazardous waste under the Resource Conservation and
Recovery Act (RCRA) depending on several factors as described in the paragraphs that follow. Upon disposal used and unused
fuel cells/cartridges may be classified as ignitable hazardous waste (waste code D001) under U.S. EPA regulations.
Hazardous waste generated by homeowners and contractors who perform routine maintenance for homeowners in their homes are
not regulated by RCRA. In general, "household wastes" generated by homeowners and their contractors are exempt from hazard-
ous waste regulation because those wastes are expressly excluded from the definition of hazardous waste. For example US EPA
has excluded as "household waste" aerosol cans that contain residual product and propellent. Thus under federal hazardous waste
regulations homeowners and contractors may dispose of discarded fuel cells/cartridges as general refuse in a properly permitted
municipal landfill. These users must still contact their local solid waste authority to determine if any state or local regulation
prohibits or restricts such disposal.
Paslode takes no responsibility for proper fuel cell/cartridge disposal. Proper disposal remains the responsibility of sellers and
users. All sellers and users must contact their local solid waste authority to determine if any federal, state or local regulation
prohibits or restricts disposal.