Patriot Lighting DJ4918 User manual

Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
Sku Number: 356-1131
OUTDOOR WALL LANTERN
Model Number: DJ4918
PACKAGE CONTENTS
Page 1 of 4
A
B
C
D
190724
HARDWARE CONTENTS Note: Hardware not shown actual size.
Mounting Strap Unit
X1
Mounting Screw
X2
Wire Connector
X3
End Cap
X1
Rubber Pad
X1
AA
BB
CC
DD
EE
FF
8W Type A LED Bulb (included)
X1

Page 2 of 4
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with
package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble,
install or operate the product. Contact customer service for replacement parts.
Tools Required for Assembly (not included): Screwdriver, Phillips Screwdriver, Pliers, Electrical Tape, Wire Cutters,
Safety Glasses, Ladder, Wire Stripper.
ASSEMBLY INSTRUCTIONS
PREPARATION
WARNING
●Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or
switching off circuit breaker).
●Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact
any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury
or death from electric shock.
CAUTION
●All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC).
Contact your municipal building department to learn about your local codes, permits and/or inspections.
●Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician
before installation.
●Do not connect this fixture to an electrical system that does not provide a means for equipment grounding. Never use
a fixture in a two-wire system that is not grounded. If you are not sure your lighting system has a grounding means,
do not attempt to install this fixture. Contact a qualified, licensed electrician for information with regards to proper
grounding methods as required by the local electrical code in your area.
● Select dimmable LED bulb or incandescent bulb when connecting to dimmer.
190724
Turn off the power at fuse or circuit box.
2. Attach the mounting strap unit (AA)
to the outlet box using two mounting
screws (BB). Adjust the length of
the preinstalled threaded pipe if
necessary.
1. Unscrew the end cap (DD).
Remove the rubber pad (EE)
and the mounting strap unit (AA)
from the backplate (A).
3. Install bulb (FF) .
See relamping label at socket
area or packaging for maximum
wattage allowed (Max.60W).
AA
BB
2Threaded Pipe
DD
EE
1
AA
A
Threaded Pipe
Backplate
3
FF
4. Loose the three set screws on the
glass holder, then attach the glass
shade (B) to the glass holder
carefully and secure it with the three
set screws.
NOTE: Please don’t over tighten,
breakage could occur.
4A
B
Set Screw Glass Holder

Page 3 of 4
5. Remove the four bolt nuts and the
four small rubber pads from the
metal frame (C). Attach the metal
frame (C) to the dome (D) by
aligning and inserting the threaded
rod on the metal frame (C) into the
open holes on the dome (D), then
place the four small rubber pads
over the exposed threaded rod
before screwing the four bolt nuts.
A
C
D
5
Bolt nut
Threaded
Rod
Small
Rubber
Pad
190724
ASSEMBLY INSTRUCTIONS (continued)
Turn on the power at fuse or circuit box.
6CC
AA
1
6. Pull out the source wires from the
outlet box. Make wire connections
using wire connectors (CC) as
follows:
• Connect the hot wire (usually
black insulation) from the fixture
to the black wire from the power
source.
• Connect the neutral wire (usually white insulation) from
the fixture to the white wire from the power source.
• Attach the fixture grounding wire (usually green
insulation or bare wire) to the cross bar unit (AA) with
the green grounding screw, then connect it to the
house grounding wire with the wire connector (CC).
Carefully put all of the wires back into the outlet box.
Spare Parts List:
Assembly Kit
5393MM (1 SET)
B
Glass Shade
X1
9735CS
Mounting Strap Unit
X1
Mounting Screw
X2
Wire Connector
X3
End Cap
X1
Rubber Pad
X1
AA BB CC
DD EE
The following parts are available for reorder if damaged or missing. Call our toll free at 1-800-887-6326.
DD
EE
7
AA A
Threaded Pipe
FF
8W Type A LED Bulb
(included)X1
8107LED
7. Attach the backplate (A) of the
fixture to the mounting strap unit
(AA) by aligning and inserting the
threaded pipe from the mounting
strap unit (AA) into the open hole
on the backplate (A), then place the
rubber pad (EE) over the exposed
threaded pipe before screwing
the end cap (DD).
Note: With silicone caulking compound, caulk
completely around where the backplate meets with
the wall surface to prevent water from seeping into
the outlet box.
Green Grounding
Screw

Page 4 of 4
190724
●Toclean, turn off and wipe with a damp, non-abrasive cloth.
1) Thelight does not come on at all:
a) Make sure the wall switch and circuit breaker are on.
b) Make sure the wiring is correct.
2) Fuse blows or circuit trips when lightis turned on.
Check for crossed wires, ensure wiring is correct.
Questions, problems, missing parts?
Before returning to your retailer, call our customer service at 1-800-887-6326
Monday – Friday 9:00 a.m. – 5:00 p.m. CST
CARE AND MAINTENANCE
TROUBLESHOOTING
FIVE-YEAR LIMITED WARRANTY: If, during normal use, this PATRIOT LIGHTING lighting fixture breaks or fails
due to a defect in material workmanship within five (5) years from the date of original purchase, simply bring this
lighting fixture with the original sales receipt back to your nearest MENARDS retail store. At its discretion, PATRIOT
LIGHTING agrees to have the product or any defective part(s) repaired or replaced with the same or similar PATRIOT
LIGHTING product or part free of charge, within the stated warranty period, when returned by the original purchaser
with original sales receipt. This warranty; (1) excludes expendable parts including but not limited to light bulbs; (2) does
not cover damage that has resulted from abuse or misuse; and (3) does not cover any losses, labor, injuries to
persons/property or costs. This warranty does give you specific legal rights and you may have other rights, which vary
from state to state.
R
R
R
R
If unable to fix any of the above issues, please consult a certified electrician.