Pax Technology E600 User manual

E600 Integrated Smart Terminal
Note: Product images shown may be different than actual
product received.
PAX TECHNOLOGY INC.

1. Contents Checklist
Please check the components after unpacking. If any one of them is missing, or if there
is a page missing from the product manual,etc., please contact the dealer.
Name
Qty.
E600
1
AC Power Adapter
1
AC Power Cable
1
Product manual
1
Charging base with external ports
1
2. Product Description
Guest Display
30W-pixel Camera
Fingerprint (optional)
Fingerprint Indicator (optional)
Main Display
Magnetic Card/ IC Card Slot
5 mega-pixel camera
Light Sensor
Power Indicator
The Front View

DC
Volume Buttons
USB
Anti-theft Hole
Speaker hole
The Right Side View
The Front Rubber Foot
Base Contact
Contraction Band
Battery Cover
The Rear Rubber Foot
The Rear View

Nameplate Sticker
SIM Card Slot
Bar Code Sticker
SD Card Slot
SIM Card Slot Diagram
Diagram for Opening the Printer Cover
3. Installation
Power on: Press and hold the Power button for three seconds until the main screen displays
normally.
Power off: Press and hold the Power button for three seconds until the shutdown menu
appears, tap “Shutdown”, and then “shutting...” appears. The terminal will be turned off after a

few seconds.
Swipe the magnetic stripe card: Place the magnetic stripe face down (keep the magnetic
stripe card perpendicular to the main display), swipe card through the magnetic card slot at a
constant speed.
IC Card: Place the IC chip face down, then insert the IC card into the card slot, and push it to
the end.
Contactless card: Put the contactless card on the center of the payment module screen.
Tear paper: Press the print paper downward along the cutter and tear it leftward or rightward
when getting close to the main display.
Charge: Insert the external adapter or the base to charge the device, the indicator lighting in
red means the device is charging; the indicator lighting in green means charging is completed;
the indicator flashing in red and green alternately meanscharging is abnormal.
Replace SIM card: Open the battery cover on the bottom of the machine,remove the battery,
and follow the prompt to insert/take out the SIM card.
Replace SD card:Open the battery cover on the bottom of the machine, remove the battery, and
follow the prompt to insert/take out the SD card.
4, Specification
Operating System: Android 7.1
CPU: Cortex A53Qaud-core, 1.4GHz
Memory: 1GB RAM + 8GB Flash Memory
Display: 8" inch, resolution:800*1280, multi-touch capacitive touch screen
Printer: 2" high-speed thermal printer, support 58*50mm print paper roll
Audio: Built-in speaker, support headphone output
Camera: Front camera, 5 mega-pixel, fixed-focus, high-speed code scanning
Rear camera,30W-pixel,fixed-focus, high-speed code scanning
L-Sensor (Ambient Light Sensor): Automatically adjust the backlight brightness of the main
display
Wireless Communication: Support WIFI, Bluetooth, 3G/4G
Positioning: Support GPS, Compass, Gingileo, GLONASS
Card Slots: SIM card slot
Micro SD card slot（maximum supports 128GB）
magnetic stripe card/IC card slot, using two-in-one（support MAG&ICC）
Magnetic Card Reader: Support track 1/2/3.
IC Card Reader: Conform to the standard of ISO7816, EMV2000 L1&L2, PBOC3.0
Contactless Card Reader: Compatible with ISO14443 Type A&B
Working Environment Temperature: 0℃～50℃(32℉～122℉)
R.H.: 10%～93%( non-condense)
Storage Environment Temperature:-20℃～70℃(-4℉～158℉)
R.H.:5％～95％ (non-condense)

5. Cautions of installation and usage
1）Avoid exposing the terminal in hot, humid,dusty or strong electromagnetic environment.
2）Do not violently vibrate, shake or beat the product.
3）Do not plug/unplug any units of the product when it is power on, otherwise it may
damage the internal circuit.
4）Do not maintain the terminal if you are non-professional
5）Before inserting the magnetic stripe/IC/contactless card, please check whether there is
any foreign object inside or surround the card slot , and if any , report to related personnel.
Caution
Risk of explosion if battery replaced by an incorrect type.
Dispose of used batteries according to the instructions.
Hereby, PAX Computer Technology (Shenzhen) Co., Ltd. declares that the radio equipment
type E600 is in compliance with Directive 2014/53/EU.
The full text of the EU declaration of conformity is available at the following internet
address：http://www.pax.com.cn/ProductCE.aspx
Icon shows
RECYCLING
This product bears the selective sorting symbol for Waste electrical and electronic
equipment (WEEE). This means that this product must be handled pursuant to European
directive 2012/19/EU in order to be recycled or dismantled to minimize its impact on the
environment.
User has the choice to give his product to a competent recycling organization or to the
retailer when he buys an new electrical or electronic equipment.
The symbol indicates DC voltage
FCC COMPLIANCE STATEMENT
This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:
1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may
cause undesired operation.
Warning
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates, uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can

be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one of the following measures:
Reorient or relocate the receiving antenna
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the
receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
Caution
Any changes or modifications not expressly approved by
the manufacturer could void the user's authority to
operate this equipment.
Radiation Exposure
This device complies with FCC radiation exposure limits
for general environments.
INDUSTRY CANADA STATEMENT
This device complies with Industry Canada license-exempt RSS standard(s).Operation is subject
to the following two conditions:
this device may not cause interference, and
this device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage
est susceptible d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or operating in conjunction with any other
antenna or transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou fonctionner en conjonction avec une
autre antenne ou un autre émetteur, exception faites des radios intégrées qui ont été testées.
The Country Code Selection feature is disabled for products marketed in the US/Canada.
La fonction de sélection de l’indicatif du pays est désactivée pour les produits commercialisés aux
États-Unis et au Canada.
Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with minimum distance 20cm
between the radiator & your body.

PAX TECHNOLOGY LIMITED reserves
the right to change product technology
specifications without notifying.
PAX TECHNOLOGY LIMITED
Manufacturer: PAX Computer Technology (Shenzhen) Co.,Ltd.
Address:4/F, No.3 Building, Software Park, Second Central Science-Tech Road, High-
Tech Industrial Park, Shenzhen, Guangdong, P.R.C.
Tel: [phone] Fax: [phone]
Website: http://www.pax.com.cn
Responsible Party: PAX Technology Inc.
Address: 8880 Freedom Crossing Trail, Building 400, 3rd Floor,
Suite 300, Jacksonville, Florida 32256
T: 1-877-859-0099