Pax Technology IM20 User manual

Installation Manual
I
IM M2 20 0
P
PO OS S
T
TE
ER RM MI IN NA AL L
PAX TECHNOLOGY LIMITED

1
1. . C
Co on nt te en nt ts s C Ch he ec ck kl li is st t
Please make sure the following items are included. If any
items are missing, contact your dealer.
Name
Qty.
IM20 POS Terminal
1
USB Cable
1
Product Manual
1
2
2. . P
Pr ro od du uc ct t D De es sc cr ri ip pt ti io on n

PAX TECHNOLOGY LIMITED
1
Figure 1: Front view
1. LCD & Touch Screen
2. IC Card & Magnetic Stripe Card Reader Slot
3. Status Indicator Light
4. Camera
5. Camera working Status Light
1
2
3
4
5

2
Figure 2: Back view
6. USB 2.0 Type-B
7. RS232
8. MDB Port
6
7
8

PAX TECHNOLOGY LIMITED
3
Figure 3: View from all angles
3
3. . I
In ns st ta al ll la at ti io on n
1) SAM Cards
Figure 4: SAM card mounts
SAM3
SAM2
SAM1

4
Remove SAM card cover. Open the mount and insert the card
into the slot with the contacts facing downwards and the
clipped corner of the card to the upper right, then lock the
mount with the card inside and replace the cover.
2) IM20 Clearance Holes and Dimensions
3) Recommended Device Mounting
Figure 5: Installation steps
4
4. . I
In ns st tr ru uc ct ti io on ns s

PAX TECHNOLOGY LIMITED
5
1) IM20 Power ON/OFF
Power on: Through the USB cable or MDB interface to the
IM20 power supply, then PAX LOGO will display
on LCD.
Power off: Disconnect the IM20 power supply, then shut
down.
2) IC Card
Put IC card chip side upward, push-in IC card slot and to
bottom.
3) Magnetic Stripe Card
Put Magnetic Stripe card stripe side downward, push-in IC card
slot and to bottom, then pull out quickly to complete the card
reading operation.
4) Contactless Card
The card read area is above the LCD, Put the card above the
LCD.
5
5. . M
Ma ai in nt te en na an nc ce e a an nd d U Us sa ag ge e
1) Do not damage any of the cables; if a cable becomes damaged,
immediately discontinue its use and seek a replacement.
2) Make sure the terminals the power or MDB cables connect to
provide the appropriate voltages at the proper pins.
3) Do not insert unknown materials into any port on the IM20,
this may cause serious damage to the device.
4) If the IM20 becomes defective, please contact a professional
technician for repairs instead of attempting them on your own.
5) The IM20 contains hardware tamper-proofing measures;
disassembly of the device will trigger the tamper circuits, at
which point it will have to be rearmed by qualified personnel
before the device is ready to resume operation.

8
6) The IM20 is designed for outdoor use; however, during normal
use its surface should still be keep clear of dirt and possible
liquid contaminants.
7) While the IM20 is designed to resist ingress of dust and liquids
from the front face, it is not designed to resist pressurized
liquids such as water hoses. Keep the back of the device away
from dust and liquids as much as possible.
FCC Regulations:
This device complies with Part 15 of the FCC Rules. Operation is
subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any
interference received, including interference that may cause
undesired operation.
This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This
equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications. However, there is no guarantee that
interference will not occur in a particular installation. If this
equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference
by one of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different
from that

PAX TECHNOLOGY LIMITED
7
to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
FCC Caution:
Any changes or modifications not expressly approved by the
party responsible for compliance could void the user's
authority to operate this equipment.
This transmitter must not be co-located or operating in
conjunction with any other antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
Industry Canada statement
This device complies with Industry Canada license-exempt RSS
standard(s). Operation is subject to the following two
conditions:
1) this device may not cause interference, and
2) this device must accept any interference, including
interference that may cause undesired operation of the
device.
Le présent appareil est conforme aux CNR d'Industrie Canada
applicables aux appareils radio exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes:
1) l'appareil ne doit pas produire de brouillage, et
2) l'utilisateur de l'appareil doit accepter tout brouillage

8
radioélectrique subi, même si le brouillage est susceptible
d'en compromettre le fonctionnement.
This device and its antenna(s) must not be co-located or
operating in conjunction with any other antenna or
transmitter, except tested built-in radios.
Cet appareil et son antenne ne doivent pas être situés ou
fonctionner en conjonction avec une autre antenne ou un
autre émetteur, exception faites des radios intégrées qui ont
été testées.
The County Code Selection feature is disabled for products
marketed in the US/ Canada.
La fonction de sélection de l'indicatif du pays est désactivée
pour les produits commercialisés aux États-Unis et au Canada.
Radiation Exposure Statement:
This equipment complies with IC radiation exposure limits set
forth for an uncontrolled environment. This equipment should be
installed and operated with minimum distance 20cm between the
radiator & your body.
Déclaration d'exposition aux radiations:
Cet équipement est conforme aux limites d'exposition aux
rayonnements IC établies pour un environnement non contrôlé.
Cet équipement doit être installé et utilisé avec un minimum de
20 cm de distance entre la source de rayonnement et votre corps.