PB TEEN Beadboard Basic Desk User manual

1 of 6
www.pbteen.com
Beadboard Basic Desk
Pre-assembly:
•Please read all instructions before starting to assemble.
•Two-person is recommended during assembly..
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
•An extra wooden knob is included for your convenience.
Hardware Included:
A - (4) Wooden knob bolts B – (4) Wooden knobs C – (1) Wooden knob with hardware attached
(4 x 28mm)
Parts Included:
D – (2) Desk Pedestal E – (1) Desk Top
Tools Required:
(1) Phillips Screwdriver( not included)

2 of 6
www.pbteen.com
Assembly:
1. For the Pedestals, gently insert Wooden knob with hardware attached (C) into the pre-drilled holes on the
front of the sliding breadboard. Attach Wooden Knobs (B) to drawers by holding Wooden Knobs (B) over
pre-drilled hole in drawer fronts. Screw Wooden Knob bolts (A) through the rear of the drawer so that it
enters the Wooden Knob (B). Tighten using a Phillips Head screwdriver, as shown.
2. Repeat for the other drawer and repeat the same steps for the second Pedestal (D).
3. Adjust the recessed levelers underneath the Pedestals’ legs, if necessary, by turning them.
4. Put the two Pedestals (D) in parallel positions and make sure they align with the positioning frames
underneath the Desktop (E). Slowly lower the top down until it sits firmly on the pedestals, as shown in the
illustration below.
5. If necessary, re-adjust the recessed levelers underneath the Pedestals’ legs to make sure the whole
assembly is balanced.
6. Hardware should be checked periodically for tightness.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.

3 of 6
www.pbteen.com
Beadboard Small Desk Hutch
Pre-assembly:
․Please read all instructions before beginning assembly.
․We recommend assembly by two adults.
․Save all packing materials until assembly is complete to
avoid accidentally discarding smaller parts or hardware.
Hardware Included:
A – Mending Plate- 2pcs B – Phillips Head Screws- 8pcs
(70x40mm) (#6x15mm)
Tools Required:
Phillips Head Screwdriver (not included). Do not use power drill as it may cause cracking.
Assembly Instructions:
7. Place Hutch on a Desk (sold separately); align Hutch and Desk center to center, as shown below. Place
Mending Plate (A) at the back of Hutch and Desk. Insert Phillips Head Screws (B) through pre-drilled holes
in Mending Plate (A) into predrilled holes at the back of the Hutch; screw another 2 Philips Head Screws (B)
through pre-drilled holes in Mending Plate (A) into back side of desk top. Loosely tighten all screws with a
Philips Head Screw Driver. Repeat on the other side of Desk for 2nd mending plate. Tighten all screws when
they are all in place.
8. For setting up the Desk, refer to Desk’s Assembly Instruction.
9. Hardware should be checked periodically for tightness.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.

4 of 6
www.pbteen.com
Beadboard Large Desk Hutch
Pre-assembly:
•Please read all instructions before beginning assembly.
•We recommend assembly by two adults.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
•An extra wooden knob is included for your convenience.
Hardware Included:
A - (2) Wooden knob bolts B – (2) Wooden knobs
(5/32” x 28mm)
C – (2) Mending plates D – (8) Small Phillips head screws (6 x 19mm) E - (2) Brackets
(70 x 40mm)
F - (2) Long screws (6 x 32) G - (2) Short screws (6 x 19) H - (1) Nylon strap
Tools Required:
(1) Phillips Screwdriver (not included)

5 of 6
www.pbteen.com
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove the hutch from box.
2. Using wooden knob hardware pack, carefully attach a Wooden knob (B) to a door, holding the knob over
pre-drilled hole in door front. Screw a Wooden knob bolt (A) through the rear of the door so that it enters the
Wooden knob (B), using Phillips screwdriver. Tighten and repeat with remaining door.
3. Two adults should lift the hutch up, and carefully place it on the desktop, as shown.
4. Using the Mending plates (C) and Phillips head screws (D), affix the back of the hutch and the desktop.
Align the Mending plate over the pre-drilled holes in the hutch, using a Phillips Head Screwdriver, and insert
the Phillips Head screws (D) through the Mending plate into the hutch and desk top, tightening with the
Phillips Screwdriver. Do not fully tighten until all screws are in place. Failure to do so may cause the parts
to misalign. Repeat on other side of hutch and fully tighten all screws. For assembly of the entire desk,
please refer to the assembly instruction for the desk.

6 of 6
www.pbteen.com
5. Locate a wall stud behind your furniture. Position a Bracket (E) on the stud approximately 1” below the top
of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill bit. Attach a Bracket (E)
to the stud with the Long Screws (F) provided.
6. On the back of the furniture, the second Bracket (E) will need to be attached to the furniture frame at the
top.To do this, temporarily move the furniture into its final position and mark the location of the wall’s
Bracket (E) on the furniture frame with a pencil.
7. Move the furniture away from the wall and place a Bracket (E) on the mark. Using the marks from the
previous step as a guide, drill holes for screws with a 3/32” drill bit. Attach the bracket to the furniture with
the Short Screws (G) provided.
8. Move the furniture into its final position, taking care to line up the wall bracket with the furniture bracket.
Thread the Nylon Strap (H) through the Bracket as shown in the illustration. Tighten strap until snug. Do not
overtighten.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.