PB TEEN Lilac Daybed User manual

www.pbteen.com
F– Wood Screws (32mm)- 32 pcs
Lilac Daybed
Pre-assembly:
•Please read all instructions before starting to assemble.
•Two adults are recommended during assembly.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
Parts included:
Hardware Included:
A – Headboard - 1 pc B – Footboard - 1 pc
E – Slat Roll - 1 setD – Front Rail - 1 pc
C – Back Panel - 1 pc

www.pbteen.com
Tools required (not included):
Phillips Head Screwdriver
Assembly:
1. Hold the Back Panel (C) up to slots on the back legs of the Headboad and Footboard (A & B). Insert the hooks of
the Back Panel (C) into the slots. Push down firmly on the top of rails until they seat themselves over the pins
inside the leg slots, as shown below.
2. Repeat the same procedure with the Front Rail (D) and the slots on the front legs of the Headboard and
Footboard (A & B).
3.
4. Lay the Slat Roll (E) on the rails of the Front Rail (D) and Back Panel (C). Using a Phillips head screwdriver,
fasten the Slat Roll (E) onto the rails with the 32 Wood Screws (F), as shown below.
3. If using with a trundle, slide assembled trundle (trundle assembly instructions are included in the trundle carton)
under daybed.
C
A
B

www.pbteen.com
4. Adjust the recessed levellers underneath the legs of the Headboard / Footboard (A,B) to make sure the whole
assembly is balanced.
5. Hardware should be checked periodically for tightness.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.

www.pbteen.com
J – Wood Screw (38mm)- 12 pcs K – Wood Screw (25mm)- 10 pcs
G – Allen Key - 1 pc H – Long Bolt (65mm)- 8 pcs I – Barrel Nut - 8 pcs
Lilac Trundle
Pre-assembly:
•Please read all instructions before starting to assembly.
•Two adult assembly is recommended
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or hardware.
Parts included:
Hardware Included:
A – Long Front Siderail - 1 pc
D – Side bottom board
(with protruding edge)- 2 pcs
C – Short Siderail - 2 pcs
(
u
p
face
)
(
down face
)
B – Long Back Siderail - 1 pc
E – Middle bottom board
(with sunken edge)- 1 pc F – Wooden bottom board support (with protruding edge)- 2 pcs

www.pbteen.com
Tools required (not included):
Phillips Head Screwdriver
Assembly:
1. Slide the Middle bottom board (E) into the (2) Side bottom boards (D) by fitting the protruding edge of the Side
bottom board (D) with the sunken edge of the Middle bottom board (E). Make sure the side with the pre-drilled
holes for wooden dowels on the Side bottom board (D) is facing up when assembling, as shown below. The
Middle bottom board (E) is reversible.
2. Attach the Wooden bottom board supports (F) to the assembly by inserting the pre-attached wooden dowels of
the Wooden bottom board supports (F) into the pre-drilled holes of the Side bottom boards (D). Insert 12 Wood
Screws (J) through the pre-drilled holes of the Wooden bottom board supports (F) and into the pre-drilled holes of
the Side bottom board (D) and the Middle bottom board (E), as shown below.
3. Attach the Long Front Siderail (A) to Short Siderail (C) using Long Bolt (H) and Barrel Nut (I). Position the Long
Front Siderail (A) and Short Siderail (C) by inserting the pre-assembled wooden dowels on the end of the Long
Front Siderails (A) into the pre-drilled holes for the wooden dowels on the end of the Short Siderail (C). Insert
Barrel Nut (I) into the holes on each end of Long Front Siderail (A). Then, connect Long Front Siderail (A) to the
Short Siderail (C) with a Long Bolt (H). The Long Bolt (H) goes through the countersunk hole in the end of Short
Siderail (A) and into the Barrel Nut (I) at the end of the Long Front Siderail (A), as shown below. Tighten by using
Allen Key (G). Repeat this step with the remaining Short Siderail (C) and the Long Back Siderail (B).
E
DE
IH
B

www.pbteen.com
4. Insert and tighten 10 Small Wood Screws (K) into the pre- drilled countersunk holes on the inner rails of the Long
Front Siderail (A), the Long Back Siderail (B) and the Short Siderail (C) as shown below.
5. Hardware should be checked periodically for tightness.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.