PB TEEN Paramount Desk User manual

1
www.pbteen.com
Paramount Collection
Desk
PRE-ASSEMBLY:
For your safety and ease, assemblyby two adults is recommended.
Please read all instructions before beginning assembly. The illustrations provided allow for easier assembly
when used in conjunction with the assembly instructions.
Remove all parts and hardwarefrom box and lay out on a carpeted or scratch-freework surface. The shipping
box provides and idealwork surface. Do not disposeof any contents until assembly is completed to avoid
accidentally discarding small parts or hardware.
Use the parts and hardware lists to identify and separate each of the pieces included prior to starting
assembly.
Note: DO not fully tighten the bolts until all parts are in place. Failure to follow these instructions may cause
the bolts to misalign during assembly.
Do not use power drill as it may cause cracking.

2
www.pbteen.com
Carton 1: Carton 2: Carton 3: Carton 4:
Hardware Enclosed:
(C) Desk Top –1 pc
(D) Desk 1 Drawer –1 pc
(E) Desk 3 Drawer –1 pc
(F) Desk Center –1 pc
(H) Wood Grommet –1 pc
(S) Shelf –1 pc
(G) Back Panel –1 pc
Packed in Carton
( Desktop )
Packed in Carton
( Desk 1 Drawer )
Packed in Carton
( Desk 3 Drawer )
Packed in Carton
( Desk Center )
(M) Bolts –6 pcs (M6x30mm
(P) Plate –1 pc
(P) Plate –1 pc
(P) Plate –2 pcs
(L) Allen Key –1 pc
(L) Allen Key –1 pc
(L) Allen Key –1 pc
(L) Allen Key –1 pc
(T) Bolts –4pcs (M6x15mm)
(T) Bolts –4pcs (M6x15mm)
(T) Bolts –8pcs (M6x15mm)
(K) Shelf Support –4pcs
(N) Bolts –6pcs (M6x20mm )
(O) Lock Washer –2pcs
(R) Half Moon –2pcs
(U) Bolt –2pcs (M6x60mm )

3
www.pbteen.com
Assembly Instructions:
1. Remove the top drawer boxes from the Desk Center (F), Desk 1 Drawer (D) and Desk 3 Drawer (E) as shown
below.
2. Carefully lay down the back panel (G) and align the dowels to the pre-drilled holes on the back of the Desk Center
(F). Secure the Desk Center (F) to back panel (G) using the bolts (N) and tighten withAllen key (L) as shown below.
F
E
D
F
G
N
L

4
www.pbteen.com
3. Align the dowels from the Desk Center assembly (F) to the Desk 3 Drawer (E) on the right side, and Desk 1 Drawer
(D) on left side. Secure using bolts (N) and tighten with Allen key (L)
4. Secure the back panel (G) to Desk 1 Drawer (D) and Desk 3 Drawer (E) by attaching the bolts (U), lock washer (O),
and half moon washer (R). Tighten usingAllen key (L)
L
N
D
E
F
E
D
G
L
U
O
R

5
www.pbteen.com
5. Carefully lay the Desk Top (C) on the desk assembly with the wire hole placed onthe back side. Push Desk Top (C)
until it wedges into place. Note: Desk Top may need to be adjusted in or out to align bolt holes.
6. Secure the desk top (C) by Aligning the pre-drilled holes in the top rails of the desk assembly ( D,E,F ) with the
holes on the underside of the Desk Top (C). Secure using bolts (M) and tighten withAllen key (L)
C
D
F
E
M
L
C
D
E
F

6
www.pbteen.com
7. Re-install the drawers to the cases that were taken out earlier. Place the wood grommet (H) to close the wire
management hole.
8. Determine the desired height for the shelves (S). Insert the shelf supports (K) into the pre-drilled holes located in the
desk 1 drawer interior wall. Carefully insert the shelves (S) as shown and gently rest the shelves onto the angular
shelf support.
H
K
S

7
www.pbteen.com
Paramount Bed and Desk Configuration
Assembly Instructions
Attaching the Desk to the Bed:
1. With the help of two people, carefully move the desk assembly to its desired location, aligning the holes in the
desk assembly to the holes located in the side rail, left or right bed as shown below. Align the pre-drilled holes
on the plates (P) to the holes located in the back of the desk assembly. Insert Bolts M6x15mm (T) and loosely
tighten with Allen Key (L). Insert remaining Bolts (T) into each of the pre-drilled located in the side rail and
tighten with Allen Key (L). Note: To align the holes in Plates (P) to the side rail inserts, may require shifting of
the desk assembly. Fully tighten all bolts to secure the desk assembly to the bed.
2. To adjust the levelers:
Carefully grasp one side of the table and elevate it slightly to provide access to levelers. Turn the levelers until
adequate contact is made the floor. Carefully set the table down. Repeat until the table is level and stable.
Care Instructions:
Hardware may loosen over time. Periodically check to make sure all connections are tight. Re-tighten if necessary.
Dust often using a clean, soft, dry and lint-free cloth.
To clean, slightly moisten cloth with water. (A damp cloth holds dust and prevents scratching; dry thoroughly).
P
T
L

8
www.pbteen.com
Paramount Collection
Components and Configurations
Base Options
Paramount 2 Drawer Cabinet (A)
Paramount 2 Door Cabinet (B)
Paramount Desk (I)
( Desk Center, Desk Cabinet, Desk Pedestal )
Configurations
1- Paramount Bed and Drawer (A) and Door Cabinet (B)
2- Paramount Bed and Drawer (A), Door Cabinet (B) and Desk (I)
I
A
B
I
A
A
B
A
B
B