PB TEEN Circolo User manual

1/7
www.pbteen.com
Circolo Bed- Queen
PRE-ASSEMBLY:
•Please read all instructions carefully before assembly.
•For your safety and ease, assembly by two adults is recommended.
•Save all packing materials until assembly is complete to avoid accidentally discarding small parts or
hardware.
•Do not use a power drill as it may cause cracking.
PARTS INCLUDED:
A- Headboard (1pc)
B- Footboard (1pc)
C- Side Rail (2pcs)
D- Slat Roll (1pc)
E- Slat Support (1pc)
F1- Long Support Legs (for higher setting) (3pcs)
F2- Short Support Legs (for lower setting) (3pcs)
G- Finials (4pcs)
HARDWARE INCLUDED:
H- Large Phillips Head Screw (8x25mm) (36pcs)
I- L Shape Bracket (1pc)
J- Small Phillips Head Screws (6x15mm) (6pcs)
TOOLS REQUIRED (but not included):
•Phillips Head Screwdriver

2/7
www.pbteen.com
ASSEMBLY INSTRUCTIONS:
1. Determine the desired location of the bed. Attach the Side Rails (C) to the Headboard (A) and Footboard
(B) by inserting the hooked ends into the corresponding slots as shown below. Push firmly on Side Rail
(C) to set into place. Please Note: Side Rails (C) can be adjusted to two settings, L1 (highest setting) and
L2 (lowest setting); where you place the Side Rails (C) will depend on where to attach the L Shaped
Bracket (I).
2. Attach the “L” Shape Bracket (l) onto the Headboard (A) by aligning the pre-drilled holes on the L Shaped
Bracket (I) to the correct pre-drilled holes corresponding to the Side Rail (C) location as described in Step
1. Insert Small Phillips Head Screws (J) as shown below; tighten using a Philips Head Screwdriver.
3. If the L Shaped Bracket (I) is in the L1 position on the Headboard (A) the Long Support Legs (F1) will be
use to assemble the Slat Support (E). If the L Shaped Bracket (I) is in the L2 position the Short Support
Legs (F2) will be use to assemble the Slat Support (E). Once correct Support Legs are determined screw
the Support Legs with the pre-attached screw into the pre-drilled holes on the Slat Support (E) as shown
below.
4. Attach the Slat Support (E) to the L Shape Bracket (I) by inserting the Small Philips Head Screws (J)
through the L Shaped Bracket into the Slat Support (E) as shown below; tighten using a Philips Head
Screwdriver.
Figure 1
Figure 2

3/7
www.pbteen.com
5. Lay the Slat Roll (D) on the Side Rails (C), insert Large Philips Head Screws (H) threw the pre-drilled
holes on the Slat Roll (D) and into the Side Rails (C), tighten using a Philips Head Screwdriver. Then
insert Large Philips Head Screws (H) into the pre-drilled holes located in the middle of the first and last
slat, tighten using a Philips Head Screwdriver as shown below.
6. Insert the pre-attached screw on the Finials (G) into the pre-drilled holes on each bed post, turn clockwise
to tighten.
CARE INSTRUCTIONS:
•Dust often using a clean, soft, dry lint-free cloth.
•Blot spills immediately, and wipe with a clean, damp, cloth.
•We do not recommend the use of chemical cleansers, or furniture polish on our lacquered finish.
Figure 3
Figure 4
H

4/7
www.pbteen.com
Circolo Trundle
PRE-ASSEMBLY:
•Please read all instructions carefully before assembly.
•For your safety and ease, assembly by two adults is recommended.
•Save all packing materials until assembly is complete to avoid accidentally discarding small parts or
hardware.
•Do not use a power drill as it may cause cracking.
PARTS INCLUDED:
A- Long Side Rail (2pcs) B- Short Side Rail (2pcs)
C- Side Bottom Board with Protruding Edge (2pcs) D- Middle Bottom Board with Sunken Edge (1pc)
E- Bottom Board Support (2pcs)

5/7
www.pbteen.com
HARDWARE INCLUDED:
F- Large Phillips Head Screw (8x38mm) (12pcs) G- Allen Key (1pc)
H- Long Bolt (1/4”x2-1/2x13.5mm) (8pcs) I- Barrel Nut (1/4”x15x9.5mm) (8pcs)
J- Small Phillips Head Screw 8x25mm (10 pcs) K- Pan Head Screw 8x17mm (24pcs)
L- Casters (6pcs)
TOOLS REQUIRED (but not included):
1. Phillips Head Screwdriver
ASSEMBLY INSTRUCTIONS:
1. Slot the Middle Bottom Board (D) into the Side Bottom Boards (C) with the pre-drilled holes facing up as
shown below. Attach the Bottom Board Supports (E) to the bottom boards by inserting Large Phillips Head
Screws (F) into the pre-drilled holes on the Bottom Board Supports (E); tighten using a Phillips
Screwdriver.
Figure 1

6/7
www.pbteen.com
Figure 2
2. Turn assembled base over so it is right side up. Insert the wooden dowels on the ends on the Bottom
Board Supports (E) into the pre-drilled holes on the Long Side Rails (A) as shown below.
3. Insert Barrel Nut (I) into the pre-drilled hole on the Long Side Rail (A) making sure the hole of the Barrel
Nut (Z) is facing toward the pre-drilled hole on the end of the Long Side Rail (A) so the Long Bolt will slide
in. Insert the Long Bolt (H) into the pre-drilled holes in the Short Side Rail (B) and into the Long Side Rail
(A); tighten using the Allen Key (G) as shown below. Repeat for the 7 remaining Barrel Nuts and Bolts.
(A)
Figure 3
A
H
I

7/7
www.pbteen.com
Fi
g
ure 4
4. Turn assembled piece upside down; insert the Small Phillips Head Screws (J) to the pre-drilled holes as
shown below, tighten using a Phillips Screwdriver.
5. Align the pre-drilled holes on the Casters (L) to the pre-drilled holes of the assembled trundle as shown
below, insert Pan Head Screws (K) and tighten using a Phillips Screwdriver.
CARE INSTRUCTIONS:
•Dust often using a clean, soft, dry lint-free cloth
•Blot spills immediately
•Use of chemical cleansers, abrasives or furniture polish is not recommend on our lacquered finish
•Do not stand in the trundle
L
J
K