PB TEEN Chelsea Armoire User manual

www.pbteen.com
E – Large Adjustable Shelf - 2 pcs.
G – Clothes Rod - 1 pc H – Leg - 4 pcs.
F – Small Adjustable Shelf - 2 pcs.
Chelsea Armoire
Pre-assembly :
•Please read all instructions before
beginning assembly.
•Two-adult assembly is recommended.
•Save all packing materials until assembly
complete to avoid accidentally discarding
smaller parts or hardware.
Parts included:
C – Base - 1 pc
A – Left Storage 1 pc B – Right Storage 1 pc
D
–
To
p
Panel 1
p
c
I – Top Front Molding 1 pc

www.pbteen.com
J – Short Bolts - 6 pcs K – Spring Washer - 6 pcs
N – Allen Key - 1 pcM – Shelf Pin - 16 pcs
L – Flat Washer - 6 pcs
O – Long Bolts - 19 pcs
Hardware Included:
Tools required but not included:
Phillips Head Screwdriver
Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove all the parts from the boxes.
2. Determine the desired location of the piece and prepare all parts there before beginning assemble
3. Remove the drawer from the Base (C). Insert the exposed screw of the legs (H) into the pre-drilled
hole on each corner of the base (C). Turn clockwise until tight.
P – Metal Knob – 6 pcs Q - Knob Bolt 6
p
cs

www.pbteen.com
4. Place the Left Storage (A) onto the Left side of the Base(C) Aligning the Pre-drilled hole of the top of
the base(C) to pre-drilled hole of the Left Storage (A). Insert a Short Bolt (J) Spring Washer (K) and
Flat Washer (L) through the 4 pre-drilled holes of the top of the base(C) to pre-drilled hole on the
bottom of the Left Storage (A), as shown below. Tighten with the Allen Key (N).
5. Place the Right Storage (B) onto the Right side of the Base(C) Aligning the 2 Pre-drilled holes of the
top of the base(C) to 2 pre-drilled holes of the Right Storage (B). Insert a Short Bolt (J) Spring
Washer (K) and Flat Washer (L) through the 2 pre-drilled holes of the top of the base(C) to 2 pre-
drilled holes of the Right Storage (B), as shown below. Tighten with the Allen Key (N)

www.pbteen.com
6. Align the pre-drilled holes on the side of Left Storage (A) to the pre-drilled holes of the Right Storage
(B). Insert a Long Bolt (O) through the pre-drilled holes of the Right Storage (B) to pre-drilled hole of
the Left Storage (A), as shown below. Tighten with the Allen Key (N)
7. Place the Top Panel (D) on to the Left Storage (A)and Right Storage (B) Aligning the Pre-drilled hole
of the top of both storage (A,B) to the pre-drilled hole under the Top Panel (D). Insert a Long Bolt (O)
through the interior pre-drilled holes of the top of both Storage (A,B) to pre-drilled hole under the Top
Panel (D), as shown below. Tighten with the Allen Key (N)

www.pbteen.com
8. Place the Top Front Molding (I) on to the Top front of both storage (A,B) Aligning the Pre-drilled hole
of the Top Front Molding (I) to the pre-drilled hole of the top front of both storage (A,B). Insert a Long
Bolt (O) through the pre-drilled holes inside the top front of both Storage (A,B) to pre-drilled hole of
the Top Front Molding (I), as shown below. Tighten with the Allen Key (N)
9. Attach the Metal Knobs (P) to the drawer by holding the Metal knob over the pre-drilled hole in the
drawer front and inserting Knob Bolt (Q) through the pre-drilled hole on the interior of the drawer and
into the Metal Knob(P). Tighten with a Phillips Head Screwdriver. Repeat this step with the door.
Tighten with a Phillips Head Screwdriver.

www.pbteen.com
10 . Put the Shelf pins (M) into the pre-drilled holes inside the Left Storage (A). Place the Large
adjustable Shelf (E) and Put the Shelf pins (M) into the pre-drilled holes inside the Right Storage (B).
Place Small Adjustable Shelf (F) on to the Shelf Pins (M). Place the Clothes rod (G) onto the rod holder
attached to the side of the Storage (A).
Care Instructions:
•Avoid direct sunlight and excessive
temperatures.
•Dust often using a clean, soft, dry and lint-free
cloth.
•Slightly moisten cloth with water. A damp cloth
holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.

www.pbteen.com
Furniture Tipping Restraint
Young children may be injured by tipping furniture. The use of a tipping restraint is highly recommended.
When properly installed, this restraint could provide protection against the unexpected tipping of furniture
due to small tremors, bumping or climbing. We recommend mounting this restraint to a wall stud.
WARNING: This product is only a deterrent. It is not a substitute for proper adult supervision.
Hardware Included:
A - (2) Brackets B - (2) Long screws (38mm.)
C - (2) Short screws (20mm.) D - (1) Nylon strap
Installation Instructions:
1. Locate a wall stud behind your furniture. Position a Bracket (A) on the stud approximately 1”
below the top of the furniture. Mark and drill pilot hole into the center of the stud with a 3/32” drill
bit. Attach a Bracket (A) to the stud with the Long Screws (B) provided.
2. On the back of the furniture, the second Bracket (A) will need to be attached to the furniture frame
at the top.To do this, temporarily move the furniture into its final position and mark the location of
the wall’s Bracket (A) on the furniture frame with a pencil.
3. Move the furniture away from the wall and place a Bracket (A) on the mark. Using the marks from
the previous step as a guide, drill holes for screws with a 3/32” drill bit. Attach the bracket to the
furniture with the Short Screws (C) provided.
4. Move the furniture into its final position, taking care to line up the wall bracket with the furniture
bracket. Thread the Nylon Strap (D) through the Bracket and cinch as shown in the illustration.
Tighten strap until snug. Do not overtighten.