PB TEEN Twin and Full User manual

www.pbteen.com
Tune-In Bed Frame - Twin and Full
Pre-Assembly:
•Please read all instructions before beginning assembly.
•Save all packing materials until assembly is complete to avoid accidentally discarding smaller parts or
hardware.
•Two-adult assembly is recommended.
Parts Included:
A - Headboard – 1 pc B - Footboard – 1 pc
C - Side Rails – 2 pcs D - Slat Roll – 1 pc (14 pcs of Slat)
Hardwares Included:
E - Wood Screw – 28 pcs (8x30mm)
Tools Required:
Phillips Head Screwdriver (not included)
Assembly Instructions:
Step 1: Attach the two Side Rails (C) to the Headboard (A) and Footboard (B) by inserting the teeth at two
ends of the Side Rails (C) into the grooves on the Headboard (A) and Footboard (B). Press down
firmly to secure. See Figure 1.

www.pbteen.com
Figure 1
Step 2: Lay out the Slat Roll (D) on the inner edges of the Siderails (C). Screw in each slat of the Slat Roll
(D) to the Siderails (C) with the Wood Screws (E) by using a Phillips Head Screwdriver. Do not fully
tighten screws until all are in place to avoid misalignment. See Figure 2.
Figure 2
Care Instructions:
•Dust often with a soft, dry cloth.
•To clean, slightly moisten cloth with water (a damp cloth will hold dust and prevent scratching; dry
thoroughly).
B
C
C
A
D
E

www.pbteen.com
Tune-In Headboard – Twin / Full
Pre-Assembly:
•Please read all instructions before beginning assembly. Two adults are recommended for assembly.
•Please Note: If you’ve purchased the complete Tune-In Bed, please refer to the Assembly Instructions
packaged with the bed frame.
Parts and Hardware Included:
A – Headboard – 1 pc
B -ACAdapter – 1 pc
C - Audio Cord (6ft long) – 1 pc
D – Allen Bolt – 6 pcs (DIA. 1/4” x 4” L) E – Nut – 6 pcs (DIA. 1/3” x 1/4”)
F – Spring Washer – 6 pcs (DIA. 2/5” x 1/4”) G – Flat Washer – 6 pcs (DIA. 3/4” x 1/4”)
Tools Included:
H – 1/6” Allen Key – 1 pc (2” L) I – 1/4” Wrench – 1 pc (2-1/3” L)
Needed for Assembly:
Pre-assembled bed frame (not included)

www.pbteen.com
Assembly Instructions (with Wooden Bed Frame):
1. Assemble the wooden bed frame per the manufacturer’s instructions. Connect the Headboard (A) to the
bed frame by joining the hooks of the bed frame’s side rails with the female connector hook of the
Headboard (A).
Headboard
Assembly Instructions (with Metal Bed Frame):
1. Assemble metal bed frame per manufacturer’s instructions.
2. Align the pre-drilled holes of bed frame to the pre-drilled holes of Headboard (A).
3. Insert Allen Bolts (D) through a Spring Washer (F) and a Flat Washer (G) from the backside of Headboard
(A) and into the pre-drilled hole of the bed frame, as shown.
4. Once the Allen Bolt (D) exits the pre-drilled hole on the other side of the bed frame, attach Nut (E) to the
end of the Allen Bolt (D) at the front side, using a Wrench (I). Tighten the opposite side with Allen Key (H).
5. Repeat for the remaining connection points to secure the bed frame. Periodically tighten all connections.
Female Connector Hooks

www.pbteen.com
Operating Instructions:
1. Make sure the power is turned off. (Toggle the Off button completely counter-clockwise).
2. Plug the small end of the enclosed AC Adapter (B) into the “PWR” port on the control panel of the
Headboard (A).
3. Plug one end of Audio Cord (C) into the “IN” port on the control panel of Headboard (A), and the other end
into the portable player headphone jack output.
4. Turn the speaker on by toggling the “Off” button clockwise and ensure volume control is set at low level.
5. Play music using the portable player controls and adjust the volume either by using the control panel of
the Speaker Headboard (A) or portable player’s volume control.
Care Instructions:
1. Spot clean with damp cloth.
2. Cleaning agents should not be used.
3. Electrical shock hazard may cause death or serious injury, Do not operate Speaker using AC adapter
near water.
4. AC adapter is meant for indoor use only. Always plug adapter into Speaker before plugging into outlet.