PB TEEN Hampton Convertible Loft Bookcase User manual

Date: 2015-June-23
Rev: www.pbteen.com Page 1 of 7
HAMPTON CONVERTIBLE LOFT BOOKCASE
ASSEMBLY INSTRUCTION

Date: 2015-June-23
Rev: www.pbteen.com Page 2 of 7
Important Safety Instructions:
Please read all instructions carefully before assembling this bookcase.
For your safety, assembly by two or more adults is strongly recommended.
Keep these instructions for future use.
Use only vendor-supplied hardware to assembly this item. Using unauthorized hardware could
jeopardize the structural integrity of the item.
Pre-assembly:
Remove all parts and hardware from the box. Place them on a carpeted or scratch-free work surface,
as this will avoid damaging parts. The shipping box provides an ideal work surface.
To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until
assembly is complete.
Two people are recommended for your safety and ease of assembly.
Prior to starting this assembly, use the parts and hardware lists to identify and separate each of the
pieces included.
The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions
may cause the bolts to misalign during assembly.
Please use caution if using power tools to aid in assembly. Power tools can damage the hardware or
split the wood.
Part included:
A –Top Panel (x1)
B –Left Side Panel (x1)
C –Right Side Panel (x1)
D –Center Panel (x1)
E –Bottom Panel (x1)
F –Bookcase Base (x1)
G –Back Panel (x1)
H –Shelves (x2)
Hardware included:
I –Ball Tip Allen
Key
J –Long Allen Bolt
K –Short Allen Bolt
L –Spring
Washer
M –Flat Washer

4 x 95 x 30(mm)
1/4”x 57 x13(mm)
1/4”x32x13(mm)
1/4”x 10 x 1.5(mm)
1/4 ”x 12 x 1.5(mm)
1pc
4pcs
14pcs
18pcs
18pcs

Date: 2015-June-23
Rev: www.pbteen.com Page 3 of 7
N –Half Moon
Washer
O –Philips Head
Screw
P –Shelf Support
Peg
Q –Pan Head
Screw

1/4”x 24 x8(mm)
6 x 19(mm)
5x13x16x1.5(mm)
8 x 15(mm)
4pcs
21pcs
8pcs
8pcs
TOOLS REQUIRED (but not included):
Phillips Head Screwdriver
Assembly Instruction Steps:
1. Lay the Top Panel (A) upside down on a soft, scratch-free surface such as a rug or carpet as seen in the
illustration below.
2. With the help of the locating dowel, place the Left Side Panel (B) and insert the locating dowel to the left
end of the Top Panel (A). Using 2 sets of Short Allen Bolt (K), Spring Washer (L) and Flat Washer (M),
insert into the pre-drilled holes of the Left Side Panel (B) through to the pre-drilled holes of the Top Panel
(A), secure and tighten using the Ball Tip Allen Key (I) as seen with the illustration below.
3. Repeat the same step 2 on the Right Side Panel (C) to the right end of the Top Panel (A).
4. Repeat the same step 2 on the Center Panel (D) to the center of the Top Panel (A).

Date: 2015-June-23
Rev: www.pbteen.com Page 4 of 7
5. With the help of the locating dowel, place the Bottom Panel (E) and insert the locating dowel of Left, Right
and Center Panel (B,C&D) to the Bottom Panel (E).
6. Secure the Bottom Panel (E) by inserting the Half Moon Washer (N), follow by Flat Washer (M), Spring
Washer (M) and Long Allen Bolt (J) –(4sets) into the pre-drilled holes of the Bottom Panel (E) as shown
below. Tighten it by using the Ball Tip Allen Key in a clockwise direction as shown below.

Date: 2015-June-23
Rev: www.pbteen.com Page 5 of 7
7. Place the Bookcase Base (F) on the Bottom Panel (A) with the help of the locating dowel as shown below.
Secure the Bookcase Base (F) to the Bottom Panel (A) by inserting the Flat Washer (M), follow by Spring
Washer (L) and Short Allen Bolt (K) –(8sets) into the pre-drilled holes of the Bookcase Base (F) and thus
to tighten the Short Allen Bolt through into the pre-drilled holes of the Bottom Panel with the help of the Ball
Tip Allen Key in a clockwise direction. Illustration as shown below.
8. With the help of 2 adults, turn the Bookcase in an upright position as shown below.

Date: 2015-June-23
Rev: www.pbteen.com Page 6 of 7
9. Place the Back Panel (G) to the back of the Bookcase as shown below. Secure the Back Panel (G) by
inserting the Philip Head Screw x 21pcs into the pre-drilled of the Back Panel (G). Tighten it with using the
Philip Head Screwdriver (Not Included) as shown below.
10. Insert the Shelf Peg Support (P) –8sets into the adjustable pre-drilled holes on the sides of Left, Right 7
Center Panel (B, C & D) as shown below.
11. Place the Shelves (Q) onto the Shelf Support Peg (P) with your desired position and secure the Shelves (Q)
to the Shelf Support Peg (P) by inserting the Pan Head Screw (Q) underneath the holes of the Shelf
Support Peg –8sets and tighten it using the Philip Head Screwdriver (Not Included) as shown below.

Date: 2015-June-23
Rev: www.pbteen.com Page 7 of 7
12. To keep the Bookcase balance, adjust the levelers at the underneath of the Bookcase legs as shown below.
13. Assembly is completed.
Care Instructions:
Dust often using a clean, soft, dry and lint-free cloth.
Blot spills immediately and wipe with a clean, damp, cloth.
We do not recommend the use of chemical cleansers, abrasives or furniture polish on our lacquered
finish.
Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.