PB TEEN Universal Trundle User manual

Rev: 18.Dec.2012 www.pbteen.com Page 1of 5
Universal Trundle

Assembly Instructions



























Rev: 18.Dec.2012 www.pbteen.com Page 2of 5
IMPORTANT SAFETY INSTRUCTIONS:
•Please read all all instructions carefully before assembling.
•For your safety, assembly by two or more adults is strongly recommended. 
•Keep instructions for future use.
•Use only vendor-supplied hardware to assemble. Using unauthorized hardware could jeopardize the structural
integrity of the item.

PRE- ASSEMBLY:
•Remove all parts and hardware from the box and place them on a carpeted or scratch-free work surface.
The shipping box provides an ideal work surface.
•To avoid accidentally discarding small parts or hardware, please do not dispose of any contents until
assembly is complete.
•For your safety and ease of assembly, two people are recommended to assemble this item.
•Prior to starting the assembly, use the parts and hardware lists to identify and separate each of the pieces
included.
•The illustrations provided allow for easier assembly when used in conjunction with the assembly
instructions.
•Note: Do not fully tighten any of the bolts until all parts are in place. Failure to follow these instructions may
cause the bolts to misalign during assembly.
•Please use caution if using power tools to aid in assembly. Power tools can damage hardware or split the
wood.
PARTS INCLUDEED:
A –Long side rail (x2)
B –Short side rail (x2)
C –Side bottom rail with protruding
edge (x2)
D –Middle bottom rail with sunken
edge (x1)
E –Bottom board support (x2)
HARDWARE INCLUDED:
F –Ball Tip Allen Key G –Hex Bolt H –Barrel Nut I –Pan Head Screw J- Pan Head Screw
F
G
H
I
J
(included)
1/4”x63x13mm
1/4”x11x10mm
8x38mm
8x25mm
1 pc
8 pcs
8 pcs
12 pcs
10 pcs

Rev: 18.Dec.2012 www.pbteen.com Page 3of 5
K –Pan Head Screw L –Caster
K
L
8x12mm
50x50x65mm
24 pcs
6 pcs
ASSEMBLY INSTRUCTION STEPS:
1. Lay the Side Bottom Boards (C) with the pre-drilled holes facing up.
2. Slot the protruding edges of the Middle Bottom Board (D) into the sunken edges on the Side Bottom
Boards (C), as seen in the illustration below.
3. Align the wooden dowels on the Bottom Board Support (E) with the pre-drilled holes at the bottom of Side
Bottom Boards (C).
4. Screw Bottom Board Support (E) to Bottom Boards with Pan Head Screws 8x38mm (I), as shown in the
illustration below.

Rev: 18.Dec.2012 www.pbteen.com Page 4of 5
5. Fasten the Casters (L) to the Side Bottom Boards (C) with the Pan Head Screws 8x12mm (K). Make
sure to use the pre-drilled holes on the Side Bottom Boards (C) as a guide.
6. Slot the Long Side Rails (A) onto the Side Bottom Boards and attach the Short Side Rails (B) to the Long
Side Rails (A).
7. Secure with Hex Bolt (G) and Barrel Nuts (H), as shown in the illustration below.
8. Tighten all bolts withAllen Key (F).

Rev: 18.Dec.2012 www.pbteen.com Page 5of 5
9. With the help of another person, turn the assembled trundle over.
10. Tighten the Pan Screws 8x25mm (J) through the pre-drilled holes in the cleats of Side Rails (A&B) and
into the Bottom Boards (C), as shown in the illustration below.
11. Assembly is complete.
CARE INSTRUCTIONS:
•Hardware may loosen over time. Periodically check to make sure all connections are tight.
Re-tighten if necessary.
•Dust often using a clean, soft, dry, and lint-free cloth.
•To clean, slightly moisten cloth with water. (A damp cloth holds dust and prevents scratching; dry
thoroughly).
•We do not recommend the use of chemical cleaners, abrasives, or furniture polish on the product.