Teknik 5431916 User manual

NOTE: THIS INSTRUCTION
BOOKLET CONTAINS IMPORTANT
SAFETY INFORMATION.
PLEASE READ AND KEEP FOR
FUTURE REFERENCE.
English pg 1-16
Français pg 17-18
Español pg 19-20
Lot # 573596 11/23/21
Purchased: __________________
2-Shelf Bookcase
Hudson Elm finish | Model 5431916
Teknik
www.teknikoffice.co.uk

Table of Contents Assembly Tools Required
Part Identification
Hardware Identification
Hardware Usage Guide
Assembly Steps
Français
Español
Safety
Warranty
Hammer
Not actual size
No. 2 Phillips Screwdriver
Tip Shown Actual Size
3
4
5
5-16
17-18
19-20
21-22
23
Page 2

Part Identification
åWhile not all parts are labeled, some of the parts will have a label or an inked letter on the edge
to help distinguish similar parts from each other. Use this part identification to help identify similar parts.
Now you know
our ABCs.
A RIGHT END (1)
B LEFT END (1)
C TOP (1)
D BOTTOM (1)
E BACK (2)
F ADJUSTABLE SHELF (1)
A
B
C
D
E
F
E
Page 3

Hardware Identification
åScrews are shown actual size. You may receive extra hardware with your unit.
46E LEVELER - 4 1F HIDDEN CAM - 16
1R METAL PIN - 4 2R RUBBER
SLEEVE - 4
9M TOUCH-UP PEN - 1
2F CAM DOWEL - 16 42F WOOD DOWEL - 4
Page 4
CAM
COVER - 12
129P

Hardware Usage Guide
HOW TO USE A HIDDEN CAM & CAM DOWEL 2. Insert the metal end of the CAM
DOWEL into the HIDDEN CAM.
1. Push a HIDDEN CAM into
the part. The arrow in the
HIDDEN CAM must point
toward the hole in the edge
of the board.
Hole
Arrow
Metal end
Hidden Cam
Cam Dowel
Start Tighten
Arrow
Minimum
190 degrees
Caution
Risk of damage or
injury. HIDDEN CAMS
must be completely
tightened. HIDDEN
CAMS that are not
completely tightened
may loosen, and parts
may separate. To
completely tighten:
Arrow
Maximum
210 degrees
3.
Step 1
å Assemble your unit on a carpeted floor or on the empty
carton to avoid scratching your unit or the floor.
å Push two HIDDEN CAMS (1F) into the LEFT END (B).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
Look for this icon. It means a video assembly tip is
available at www.sauder.com/service/tips
Find the numbered video or scan the QR code.
B
1
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Arrow
Metal end
Page 5

Step 2
å Using your hammer, gently tap two LEVELERS (46E)
completely into the holes in the LEFT END (B).
å NOTE: Adjustments to the LEVELERS will be made later in
assembly once your unit is standing upright.
B
46E
Page 6
Just think. The sooner
you do this, the sooner
you do something else.

Step 3
å Push eight HIDDEN CAMS (1F) into the BACKS (E). Then,
insert the metal end of a CAM DOWEL (2F) into each
HIDDEN CAM.
E
E
Do not tighten the HIDDEN CAMS in this step.
Arrow
1F
2F
Metal end
Arrow
1F
2F
Metal end
Page 7

Step 4
å Fasten the BACKS (E) to the LEFT END (B).
Tighten four HIDDEN CAMS.
Surface with HIDDEN CAMS
Surface with HIDDEN CAMS
E
E
B
Do not stand the unit upright without the
BACKS fastened. The unit may collapse.
Caution
Page 8

Step 5
å Insert two WOOD DOWELS (42F) into the BOTTOM (D).
å NOTE: You may need to gently tap the WOOD DOWELS
in with your hammer.
D
42F
42F
Page 9

Step 6
å Push four HIDDEN CAMS (1F) into the BOTTOM (D).
Then, insert the metal end of a CAM DOWEL (2F) into
each HIDDEN CAM.
D
Do not tighten the HIDDEN CAMS in this step.
1F
2F
Metal end
Arrow
1F
2F
Arrow
Metal end
Page 10