PB TEEN Lilac User manual

www.pbteen.com
Lilac Vanity
Pre-assembly:
•Please read all instructions before beginning assembly.
•Two-adult assembly is recommended.
•Save all packing materials until assembly is complete to avoid
accidentally discarding smaller parts or hardware.
Parts included:
A – Left Cabinet – 1 pc B – Right Cabinet – 1 pc C – Center Drawer Unit – 1 pc
(with electric cordset) (without electric cordset)
D – Center Mirror with E – Left Mirror with F – Right Mirror with
panel – 1 pc hinges – 1 pc hinges – 1 pc
Hardware Included:
G – Hex Bolt – 11 pcs H – Spring Washer – 11 pcs I – Flat Washer – 11 pcs
(φ1/4”x32mm) (φ1/4”x11mm) (φ1/4”x15mm)
J– Allen Key – 1 pc K – Phillip Screw – 16 pcs L – Mending Plate – 2 pcs
(φ4x74x29mm) (#6x15mm for hinge) (70x40mm)
M – Wooden Knob –10 pcs N – Long Knob Bolt – 10 pcs O – Short Knob Bolt – 1 pc
(for drawers) (M4x28mm for big knob) (M4x19mm for small knob)
P – Small Wooden Knob –1 pc
(for electric cordset cover)
Tools Required: Phillip Head Screwdriver (not included)

Assembly:
1. On a soft, scratch-free surface, such as a carpet or rug, remove all the parts from boxes.
2. Determine the desired location of the piece and prepare all parts there first.
www.pbteen.com
3. Carefully remove the drawer from Center Drawer Unit (C) and assemble the Center Drawer Unit (C)
to the Right Cabinet (B). One adult should hold the Center Drawer Unit (C) while another adult
inserts a Hex Bolt (G), Spring Washer (H) and Flat Washer (I) through the pre-drilled holes on the
inside of the Center Drawer Unit (C) and into t own
below. Tighten with the Allen Key (J). Repea
(C) and the Left Cabinet (A). See illustration.
he pre-drilled holes of the Right Cabinet (B), as sh
t the same step for the other side of Center Drawer Unit
. (D) to the above assembled unit (Left Cabinet, Right Cabinet
and Center Drawer Unit) by aligning the pre-drilled holes of the Center Mirror with Panel (D) to the
pre-drilled holes on the back of the Center Drawer Unit (C). Insert a Hex Bolt (G), Spring Washer (H)
e
. Align the pre-drilled holes of a Mending Plate (L) over the pre-drilled holes on the back of Center
Mirror with Panel (D) and the Left and Right Cabinets (A & B). Insert a Phillips Screw (K) through the
pre-drilled holes of the Mending Plate (L) and into the pre-drilled holes on the back of Center Mirror
as
6.
tighten, as shown. Repeat with the Right Mirror
4 Assemble the Center Mirror with Panel
and Flat Washer (I) through the pre-drilled holes on the back of the Center Mirror with Panel (D) and
into the pre-drilled holes on the back of the Center Drawer Unit (C), as shown below. Tighten with th
Allen Key (J).
5
with Panel (D) and the Left and Right Cabinets (A & B). Tighten with a Phillips Head Screwdriver,
shown below. Periodically tighten all connections.
Attach the Left Mirror with hinges (E) to Center Mirror with Panel (D) by inserting a Phillips Screw (K)
through the holes in the hinges of the Left Mirror (E) and into the pre-drilled holes on the Center
Mirror with Panel (D). Use a Phillips Screwdriver to
with hinges (F).

7
www.pbteen.com
. Attach the Wooden Knobs (M) to the drawers on the Left and Right Cabinets (A & B) by holding the
Wooden Knob (M) over the pre-drilled hole in the drawer front. Insert a Long Knob Bolt (N) from the
interior of the drawer and into the Wooden Knob (M) and tighten with a Phillips Head Screwdriver.
. Attach the Small Wooden Knob (P) to the electric cordset cover by holding the Small Wooden Knob
(P) over the pre-drilled hole of the electric cordset cover. Insert a Short Knob Bolt (O) from the
interior side of the electric cordset cover and into the Small Wooden Knob (P). Tighten using a
9.
Care Instructions:
•Avoid direct sunlight and excessive temperatures.
•Dust often using a clean, soft, dry and lint-free cloth.
•Slightly moisten cloth with water. A damp cloth holds dust and prevents scratching.
•Waxing is not recommended on lacquered finish.
8
Phillips Head Screwdriver.
Put the drawer back to Center Drawer Unit (C). Adjust the recessed levelers located at the base of
each leg to ensure the whole unit is level.
10. Hardware should be checked periodically for tightness.

Lilac Vanity
FURNITURE TIPPING RESTRAINT
: This product is only a deterrent. It is not a substitute for proper adult supervision.
s no liability for improper installation or excessive loads placed on screws, brackets
Young children may be inj aint is highly
commended.
end mounting this restraint to a wall stud.
48 x 21 x 10mm
(1) Nylon Strap 300 x 12 x 8mm
ting it is essential to use the proper hardware for your wall type.
r stud mounting only. For other wall
lease consult your local hardware store.
. Determine the final resting position of the furniture piece. Mark
screws provided.
. Move the furniture away from the wall and place a bracket on the
4. ket is firmly screwed into wall stud
and the furniture bracket is firmly attached to the frame.
5.
WARNING
Manufacturer assume
straps.
or
ured by tipping furniture and the use of a tipping restr
re
When properly installed, this restraint could provide protection against the unexpected tipping of furniture.
We recomm
Hardware included:
•(2) Brackets
•
•(2) Stud Mounting Screws 6 x 32mm
•(2) Product Side Mounting Screws 6 x 19mm
Note: For safe moun
The included hardware is for drywall o
types (ie: plaster, concrete, brick…) p
1
Stud
Wallboard
location on the wall approximately 1” below the top of the back of
the furniture. Mark and drill pilot hole into the center of the stud
with a 3/32” drill bit. Attach a bracket to the stud with the long
2. On the back of the furniture, a bracket will need to be attached to
the furniture frame at the top. To do this, temporarily move the
furniture into its final position and mark the location of the wall
bracket on the furniture frame.
3
Furniture Frame
mark. Mark and drill holes for screws with a 3/32” drill bit. Attach
the bracket to the furniture with the short screws provided.
Check to be sure the wall brac
Move the piece of furniture into its final position so that the wall
bracket and furniture bracket are in alignment.
6. Thread the strap through brackets and tighten until snug. Do not
over- tighten. Wallboard
www.pbteen.com
7. Check to make sure the brackets are firmly installed and the strap
is secure.
Furniture Frame
Stu
d
Completed Anti-tip Kit Installation