PDK RED 2 User manual

3. Reader Connection2. Mounting Controller
6. Locking Relay
5. Input B / REX Connection4. Input A / DPS Connection
1. Package Contents
Jumpers (4)
Diodes (2)
Red 2
Two Door Controller (1)
Battery Leads (1)
Key Lock (1)
Mount - Mount the Red 2 enclosure securely to a wall.
OSDP
Wiring
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
AMain Reader - The main reader is mounted at the door with a 22/5 or 22/6
wire ran to the door controller. Wire the reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering controller.
BSecondary Reader - Wire the second reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
DPiezo - Can be connected to available relay and configured with software
COSDP - Place jumper(s) to enable OSDP (see OSDP reference guide at the
end of this guide for more info)
DB
C
AReader
Red 2 Controller
+ -
0 1 L
Double DPS
Contact
ADPS (Door Position Switch) - The DPS is mounted on the door frame in the
desired location with a 22/2 wire running from the DPS to the controller.
Wire the DPS to the controller as shown above. When using two DPS sensors
for double doors you will wire them in series with only two conductors
running back to the controller for connection.
AUX Input - A rule can be setup to trigger events or outputs based on this
input trigger.
B
DPS Contact
A
B
If using a powered REX,
run to any 12VDC
output on controller.
B
A
Maglock
REX
C
PORT1
BUS
+-
Maglock - When installing a Maglock it is typical to install a REX (Request to
Exit) at the door for free egress. Run an 18/2 wire from the Maglock to the
Door Controller, connecting to the Maglock as shown.
REX (Request to Exit) - The REX is mounted in the desired location with an
18/5 wire ran from the REX to the controller. Wire the REX to the controller
and maglock as shown above. If reporting is not needed in the system , simply
eliminate the green labeled wire.
A
B
Jumper - Use the designated jumper(s) to energize the relay output NO and
NC to utilize the output as a wet contact.
C
Diode - The provided diode must be installed when using a strike. Install at
the strike with the grey stripe of diode on positive and the black on negative.
NC - Used for maglocks (or strikes in fail-safe configuration). Connect the
negative (-) of the maglock or strike to NC on the door controller.
NO - Used for strikes in fail-secure configuration. Connect the negative (-) of
the strike to NO on the door controller.
Jumper - Use the designated jumper(s) to energize the relay output NO and
NC to utilize the output as a wet contact.
C
AD
PORT1
BUS
+-
BOR
A
B
C
D

Reference Guide
8. Power Connection
OSDP Reference Guide
7. Communication Connections
Ethernet - Red controllers accept RJ45 connections. The Red 2 controller
will be Self-Discoverable from Pdk io software. You have the option to
assign a Static IP address but is not required.
A
Wireless (PN: RMW) and PoE (PN: RMPOE)
module kits can be purchased for optional
communication add-ons.
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
A
DC INPUT - Use included 14 VDC, 2 Amp transformer for DC power
input. It is recommended to use 18/2 wire. For high voltage applications, use
the HV Converter (PN: HVC).
BATTERY - The enclosure will fit most 12 VDC 5 Ah batteries. The battery is
connected with supplied leads and is polarity sensitive. Receive up to 8 hrs of
battery backup using a strike in fail-secure.
A
A
B
Battery
12 VDC / 5 Ah
B
What is OSDP - Open Supervised Device Protocol (OSDP) is an access control
communications standard developed by the Security Industry Association to
improve interoperability among access control and security products. OSDP
brings heightened security and improved functionality. It is more secure than
Wiegand and supports AES-128 encryption.
OSDP Wire Specication - Four (4) conductor twisted pair overall shield is
recommended to remain fully TIA-485 compliant at maximum supported baud
rates and cable distances.
NOTE - It’s possible to reuse existing Wiegand wiring for OSDP, however, using
simple stranded cable typical of Wiegand readers generally does not meet the
RS485 twisted pair recommendations.
OSDP Multi-Drop - Multi-drop gives you the capability to accommodate
many readers by running one length of 4-conductor cable, eliminating the
need to run wire for each wire.
NOTE - Four (4) is the maximum number of readers each port can support.
NOTE - Wiegand readers will not work when OSDP jumpers are installed.
Fire Input - To integrate the fire system using a Red 2 door controller, refer to
wiring diagrams in the Partner Portal at
www.prodatakey.com/resources
Programming - After the Red 2 door controller has been connected back to
the Cloud Node, access the configuration software as instructed in the
programming manual. This manual is available for download through the
Partner Portal at www.prodatakey.com/pdkio
Reader Compatibility - ProdataKey does not require proprietary readers.
Door controllers accept a wiegand input, including biometric readers and
keypads. OSDP readers are supported by using included jumper (see OSDP
reference guide). Contact support for details.
UL 294 Compliance - All equipment must meet appropriate UL certifications.
For UL listed installations, all cable runs must be less than 30 meters (98.5’)
Part Number - R2
PDK Technical Support
Phone: [phone] option #2
Email: [e-mail]
PDK Knowledge Base: prodatakey.zendesk.com
www.prodatakey.com
801.317.8802
REV 01142022
View the user manual here:
prodatakey.zendesk.com
PN:R2
Copyright © 2022 ProdataKey Inc. All rights reserved. Pdk, Pdk io, and
the Red logos are trademarkes of ProdataKey Inc.
Quick Start Guide