PDK Red RGE User manual

3. Reader Connection
2. Mounting Controller
6. Locking Relay
5. Input B / REX Connection4. Input A / DPS Connection
1. Package Contents
Jumpers (4)
Diodes (2)
Red Gate Controller (1)
Battery Leads (1)
Enclosure Screws (4)
Mount - Mount the Red Gate enclosure securely to a wall.
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
AReader - The reader is mounted at the door with a 22/5 or 22/6 wire running
to the door controller. Wire the reader to the controller as shown above. Be
sure to check polarity and voltage prior to powering the controller.
CPiezo - Can be connected to available relay and configured with software
BOSDP - Place jumper(s) to enable OSDP (see reference guide for more
information about OSDP.)
OSDP Wiring
C
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
AReader
Red Gate Controller
B
B
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
ADPS (Door Position Sensor) - The DPS is mounted on the door frame with a
22/2 wire running from the DPS to the controller. Wire the DPS to the
controller as shown above. For reporting double doors, wire the two door
position in series and connect to the controller.
B
AUX Input - A software rule can be programmed to trigger events or
outputs based on input triggers.
B
A
-
B
Double
DPS Contact
A
DPS Contact
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
If using a powered REX,
run to any 12VDC
output on controller.
BREX Maglock
A
C
PORT1
BUS
+-
D
Maglock - When installing a Maglock, it is typical to install a REX (request to
exit) at the door for free egress. Run an 18/2 wire from the maglock to the
controller and REX as shown.
REX (Request to Exit) - The REX is mounted at your desired location with an
18/5 wire. Wire the REX to the controller and maglock as shown above. If
reporting is not needed in the system, simply eliminate the green input wire.
A
B
Jumper Block - Use to designated (+) or (-) board voltage out of NO and NC.
If the jumper is off, the relay is a standard dry contact requiring an input into
C on the relay.
C
DAUX Input - A software rule can be programmed to trigger events or outputs
based on input triggers.
Gate Operator - Follow the gate operator wiring instructions to connect the
gate operator to an ELK 912B Isolation Relay.
Isolation Relay - Installation of an ELK 912B isolation relay is recommended
to prevent electrical damage to the Red Gate, The isolation relay is
sold separately.
Locking Relay - Connect the ELK 912B isolation relay to the controller by
connecting the positive wire into a positive port and the negative wire into
the NO port on the board.
Jumper Block - Use to designated (+) or (-) board volatage out of NO and NC.
If the jumper is off, the relay is a standard dry contact requiring an input into
C on the relay negative (-) and center pins.
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
C
A
D
B
NO NO COM
D2
Wiring from Gate Operator
-
+
PORT1
BUS
+-
ELK 912B
Isolation Relay
(sold separately)
A
B
C
D

Reference Guide
8. Power Connection
OSDP Reference Guide
7. Communication Connections
Ethernet - All Red controllers come with a built-in RJ45 connection for
network connectivity. Once connected, the Red Gate controller is
Self-Discoverable from pdk.io using IPV6. Alternatively, you may use IPV4
or assign a static IP using pdk.io if desired.
A
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
A
DC INPUT - Input 12-24 VDC power using an 18/2 wire. For high voltage
applications, use the High Voltage Converter (PN: HVC).
BATTERY - The enclosure will fit most 12 VDC 1.2 Ah batteries. Connect the
battery to the controller using the supplied battery leads.
A
B
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
A
B
Battery
12 VDC / 1.2 Ah
What is OSDP - Open Supervised Device Protocol (OSDP) is an access control
communications standard developed by the Security Industry Association to
improve interoperability among access control and security products. OSDP
brings heightened security and improved functionality. It is more secure than
Wiegand and supports AES-128 encryption.
OSDP Wire Specication - Four-conductor twisted-pair with overall shield is
recommended to remain fully TIA-485 compliant at the maximum supported
baud rates and cable distances.
NOTE - It’s possible to reuse existing Wiegand wiring for OSDP, however, using
simple stranded cable typical of Wiegand readers generally does not meet the
RS485 twisted pair recommendations.
OSDP Multi-Drop - Multi-drop gives you the capability to accommodate
many readers by running one length of four-conductor cable, eliminating the
need to run wire for each wire.
NOTE - The maximum number of readers each port can support is four.
NOTE - Wiegand readers will not work when OSDP jumpers are installed.
Fire Input - To integrate the fire system into a controller, refer to wiring
diagrams at www.prodatakey.zendesk.com
Programming - After the controller is connected, access the configuration
software as instructed in the programming manual availabe at
www.prodatakey.zendesk.com
Reader Compatibility - Pdk does not require proprietary readers.
Controllers accept a Wiegand input, including biometric readers and
keypads. OSDP readers are supported by using included jumper (see OSDP
reference guide). Contact pdk support if assistance is needed.
UL 294 Compliance - All equipment must meet appropriate UL certifications.
For UL listed installations, all cable runs must be less than 30 meters (98.5’)
Part Number - RGE
PDK Technical Support
Phone: [phone] option #2
Email: [e-mail]
PDK Knowledge Base: www.prodatakey.zendesk.com www.prodatakey.com
801.317.8802
REV 06032022
View the user manual here:
prodatakey.zendesk.com
PN:RGE
Copyright © 2022 ProdataKey Inc. All rights reserved. Pdk, Pdk io, and
the Red logos are trademarkes of ProdataKey Inc.
Quick Start Guide
gate
outdoor controller
ethernet