PDK Red Pedestal RPE User manual

3. Reader Connecon
2. Mounng Controller
6. Locking Relay
5. Input B / REX Connecon4. Input A / DPS Connecon
1. Package Contents
Jumpers (4)
Diodes (2) Baery Leads (1) Nuts (4)
Red Pedestal Controller (1) Bolts (4)
Mount - Mount the Red Pedestal enclosure securely.
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
OSDP
Wiring
D
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
B
C
AReader
+ -
0 1 L
AMain Reader - The main reader is mounted at the door with a 22/5 or 22/6
wire ran to the door controller. Wire the reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
BSecondary Reader - Wire the second reader to the controller as shown
above. Be sure to check polarity and voltage prior to powering the controller.
DPiezo - Can be connected to available relay and configured with soware
COSDP - Place jumper(s) to enable OSDP (see OSDP reference guide at the
end of this guide for more info)
Red Pedestal Controller
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
Double DPS
Contact
A
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
DPS (Door Posion Switch) - The DPS is mounted on the door frame in the
desired locaon with a 22/2 wire running from the DPS to the controller.
Wire the DPS to the controller as shown above. When using two DPS
sensors for double doors, you will wire them in series with only two
conductors running back to the controller for connecon.
AUX Input - A rule can be set up to trigger events or outputs based on this
input trigger.
B
DPS Contact
A
B
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
If using a powered REX,
run to any 12VDC
output on controller.
B
A
Maglock
REX
C
PORT1
BUS
+-
Maglock - When installing a Maglock, it is typical to install a REX (Request
to Exit) at the door for free egress. Run an 18/2 wire from the Maglock to
the door controller, connecng to the Maglock as shown.
REX (Request to Exit) - The REX is mounted in the desired locaon with an
18/5 wire ran from the REX to the controller. Wire the REX to the controller
and Maglock, as shown above. If reporng is not needed in the system,
simply eliminate the green-labeled wire.
A
B
Jumper - Use the designated jumper(s) to energize the relay output NO and
NC to ulize the output as a wet contact.
C
Gate Operator - Follow the gate operator wiring instrucons to connect the
gate operator to an ELK 912B Isolaon Relay.
Isolaon Relay - Installaon of an ELK 912B Isolaon relay is recommended
to prevent electrical damage to the Red Gate, Isolaon relay is
sold separately.
Locking Relay - Connect the ELK 912B Isolaon relay to the Red Pedestal
by connecng the posive wire into a posive port and the negave wire
into the NO port on the board.
Jumper - Use the designated jumper(s) to energize the relay output to be
NO by placing the jumper on the negave (-) and center pins.
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
C
A
D
B
NO NO COM
D2
Wiring from Gate Operator
-
+
PORT1
BUS
+-
ELK 912B
Isolaon Relay
(sold separately)
A
B
C
D

Reference Guide
8. Power Connecon
OSDP Reference Guide
7. Communicaon Connecons
+ -
0 1 L +
-
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
OSDP
PORT1
BUS
+-
PORT2
BUS
+-
ETHERNET
POWER
HEART
LINK
ACTIVITY
BATTERY
POE IN
POE OUT
A
Ethernet - All Red controllers come with a built-in RJ45 connecon for
network connecvity. Once connected, the Red Pedestal controller is
Self-Discoverable from pdk.io using IPV6. Alternavely, you may use IPV4
or assign a stac IP using pdk.io if desired.
A
+ -
0 1 L
A
-
B A
-
B NC NOCNC NOC 12VDC
+GND
OSDP
PORT1
BUS
+-
PORT2
BUS
+-BATTERY
DC INPUT - Use included 14 VDC, 2 Amp transformer for DC power
input. It is recommended to use 18/2 wire. For high voltage applicaons, use
the HV Converter (PN: HVC).
BATTERY - The enclosure will fit most 12 VDC 1.2 Ah baeries.
The baery is connected with supplied leads and is polarity sensive.
A
A
B
Battery
12 VDC / 1.2 Ah
B
What is OSDP - Open Supervised Device Protocol (OSDP) is an access
control communicaons standard developed by the Security Industry
Associaon to improve interoperability among access control and security
products. OSDP brings heightened security and improved funconality. It is
more secure than Wiegand and supports AES-128 encrypon.
OSDP Wire Specificaon - Four (4) conductor twisted pair overall shield is
recommended to remain fully TIA-485 compliant at maximum supported
baud rates and cable distances.
NOTE - It’s possible to reuse exisng Wiegand wiring for OSDP; however,
using simple stranded cable typical of Wiegand readers generally does not
meet the RS485 twisted pair recommendaons.
OSDP Mul-Drop - Mul-drop gives you the capability to accommodate
many readers by running one length of 4-conductor cable, eliminang the
need to run wire for each wire.
NOTE - Four (4) is the maximum number of readers each port can support.
NOTE - Wiegand readers will not work when OSDP jumpers are installed.
Fire Input - To integrate the fire system using a Red Pedestal, refer to wiring
diagrams at prodatakey.zendesk.com
Programming - Aer the Red Pedestal controller has been installed, full
configuraon and system programming will be performed within the pdk io
soware. Full configuraon instrucons can be found in the programming
manual at prodatakey.zendesk.com
Reader Compability - ProdataKey does not require proprietary readers.
Door controllers accept a wiegand input, including biometric readers and
keypads. OSDP readers are supported by using an included jumper (see
OSDP reference guide). Contact support for details.
UL 294 Compliance - All equipment must meet appropriate UL
cerficaons. For UL listed installaons, all cable runs must be less than 30
meters (98.5’)
Part Number - RPE
PDK Technical Support
Phone: [phone] opon #2
Email: [e-mail]
PDK Knowledge Base: prodatakey.zendesk.com
www.prodatakey.com
801.317.8802
REV 01032022
View the user manual here:
prodatakey.zendesk.com
PN: RPE
Copyright © 2022 ProdataKey Inc. All rights reserved. Pdk, Pdk io, and
the Red logos are trademarkes of ProdataKey Inc.
Quick Start Guide
outdoor controller
ethernet