PEERLESS JCT-P1642E Guide

3215 W. North Ave. • Melrose Park, IL 60160 • [phone] or [phone] • Fax: [phone] • www.peerlessindustries.com
ISSUED: 01-19-05 SHEET #: 009-9031-2 02-23-05
Installation and Assembly:
Video and Utility Table
Model: JCT-P1642E, JCT-P2642CE

2 of 4 ISSUED: 01-19-05 SHEET #: 009-9031-2 02-23-05
• Do not begin to install your Peerless product until you have read and understood the instructions and warnings
contained in this Installation Sheet. If you have any questions regarding any of the instructions or warnings, please
call Peerless customer service at 1-800-729-0307.
• This product should only be installed by a qualified professional.
• Unit should be moved by authorized adults only.
• Prior to moving tables, place allAV equipment materials on lowest shelf possible. Secure heavy or bulky equipment
to table with safety belts.
• Disconnect all electrical cords from wall outlets and secure to equipment on table.
• Unlock all casters, push mobile table from the narrow side of unit only. Never pull.
• Avoid rough or uneven flooring and remove any obstacles in your path.
• Apply force to the narrow side. Do not pull the unit.
• When set up for stationary use or when loading or unloading equipment, books, etc., always secure the casters
before doing so.
• When using the table as an equipment stand, the equipment should be put on the lowest possible shelf that will still
allow the equipment to operate correctly. The equipment should be placed in the center of the shelf it is sitting on.
• The product should not be used as a stool or a ladder.
WARNING
I
H
Some parts may appear slightly different than illustrated.
A
P
B
K
J
C
G
LMN
O
Parts List
Description Qty. Part #
Atop shelf (with handle) 1 009-0207
Bmiddle shelf (w/ 8 leg bosses) 1 009-0208
Cbottom shelf (w/ caster inserts) 1 009-0209
Dcable management clips (not shown) 3 590-0117
E4" casters without brakes (not shown) 2 560-0082
F4" casters with brakes (not shown) 2 560-0083
Gcord wrap clip 1 009-1168
H15' extension cord 1 600-1011
Ismall phillips head bolts 2 520-1219
Jwingnuts 2 530-1025
K8 1/2" legs 4 009-0212
L16 1/2" legs 8 009-0210
M18 1/2" legs (JCT-P1642E only) 4 009-0211
Ngrooved legs (JCT-P2642CE only) 4 009-0203
Oback panel (JCT-P2642CE only) 1 009-0204
Pside panel (JCT-P2642CE only) 2 009-0205
Qdoor panel (JCT-P2642CE only) 1 009-0206
Q

3 of 4 ISSUED: 01-19-05 SHEET #: 009-9031-2 02-23-05
Use a rubber mallet (or optional metal hammer
with wood block) to firmly seat legs into leg
encapsulation cavities of the top shelf (A),
rotating around table in stages to avoid dam-
aging shelf or legs.
Separate legs by length. Lay top shelf (A) face
down on a flat, firm surface, preferably a non-
carpeted concrete floor. By hand, firmly push
the proper size legs that go between the top
shelf and the middle shelf (B) into place on leg
bosses.
Set middle shelf (B) onto legs from the top
shelf (A) and set legs onto the leg encapsula-
tion cavities by hand.
Use rubber mallet to firmly seat shelf (B) onto
legs, rotating around the table in stages to
avoid damaging shelf or legs.
A
AA
B
B
16" (4) 8 1/2" (top and bottom shelves only)
26" (4) 18 1/2" (top and bottom shelves only)
34" (4) 8 1/2" and (4) 16 1/2"
42" (8) 16 1/2"
Desired
Unit
Height
Use These Legs
Now position legs that go between middle and
bottom shelves into place by hand. Use rubber
mallet to firmly seat into shelf, rotating around
the table in stages to avoid damage. Note: For
model JCT-P2642CE, use four grooved legs
(N) for this step.
A
B
For JCT-P1642E
24" (4) grooved legs (top and bottom shelves only)
34" (4) grooved legs and (4) 8 1/2"
42" (4) grooved legs and (4) 16 1/2"
Desired
Unit
Height
Use These Legs
For JCT-P2642CE

4 of 4 ISSUED: 01-19-05 SHEET #: 009-9031-2 02-23-05
Position bottom shelf leg bosses onto legs by
hand. Then, using rubber mallet, proceed to
firmly seat legs into encapsulation cavities of
bottom shelf by rotating in stages around the
table until all legs are fully seated.
Pound casters into caster sockets on under
side of bottom shelf with rubber mallet.
G
I
H
J
Fasten cord wrap clip (G) and extension cord
(H) to top shelf using two screws (I) and two
wing nuts (J) as shown.
© 2005 Peerless Industries, Inc. All rights reserved.
Peerless is a registered trademark of Peerless Industries, Inc.
All other brand and product names are trademarks or registered trademarks of their respective owners.
O
P
Q
Locate back panel (O) and slide down into
grooves of two back legs. Take two side panels
(P) and slide into place. Take front panel (Q) and
slide into place with the lock positioned as shown.
LOCK
Step 6 is for model JCT-P2642CE only!