pellenc Excelion 1200 User manual

pellenc s.a.
Route de Cavaillon
B.P. 47
84122 PERTUIS cedex
(France)
Tel : [phone] Fax : [phone]
E-mail : [email protected]
www.pellenc.com
Translation of the
original user guide
CONTENTS:
READ THE USER GUIDE CAREFULLY BEFORE USING THE TOOL
ENG
Grass cutting
Brush-cutter
• Grass cutting brush-cutter with safety elements
• Adjustment wrench
• Harness
• User guide
• Harness adjustment sheet
53_84107_E - 11/2013
USER GUIDE

Table of contents
INTRODUCTION.............................................................................3
BILAN CARBONE ...............................................................................................9
SAFETY INSTRUCTIONS ....................................................................10
GENERAL SAFETY INSTRUCTIONS FOR THE TOOL.................................................................11
SAFETY WARNINGS FOR THE EXCELION BRUSH CUTTER AND GRASS TRIMMER.......................................12
SAFETY MEASURES FOR THE CHARGER AND THE BATTERY ........................................................13
SAFETY EQUIPMENT ..........................................................................................14
SAFETY INDICATIONS ......................................................................14
DESCRIPTION AND TECHNICAL CHARACTERISTICS ............................................15
TECHNICAL CHARACTERISTICS .................................................................................16
PREPARING THE MACHINE FOR USE .........................................................16
ASSEMBLY/DISASSEMBLY OF THE FRONT HANDLE ................................................................17
ASSEMBLY/DISASSEMBLY OF THE CARRYING EYE AND THE DISTANCING DEVICE ......................................17
ASSEMBLY/DISASSEMBLY OF THE SAFETY CASING ................................................................17
ADJUSTING THE WORKING POSITION. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
ADJUSTING THE WORKING POSITION............................................................................18
ADJUSTING THE POSITION OF THE FRONT HANDLE ...............................................................18
ATTACH AND ADJUST THE LENGTH OF THE HARNESS, .............................................................19
THE HARNESS (
supplied with the tool
).............................................................................19
ADJUSTING THE LENGTH OF THE TELESCOPIC TUBE ..............................................................20
ADJUSTING THE CUTTING HEAD ORIENTATION....................................................................20
STARTING UP AND OPERATION ..............................................................21
START-UP ....................................................................................................21
HANDLING THE MACHINE ......................................................................................21
HEAD ROLL CUT ..............................................................................................23
HEAD TAP CUT ...............................................................................................25
MULTI-CUT CUTTING HEAD .....................................................................................27
MAINTENANCE ............................................................................29
PART NUMBERS FOR SPARE PARTS .............................................................................30
INCIDENTS ................................................................................32
«PELLENC SA» TERMS OF WARRANTY AND NON-RESPONSIBILITY CLAUSE .......................35
‘‘CE’’ STATEMENT OF CONFORMITY ..........................................................37

3
INTRODUCTION
Dear customer,
Thank you for purchasing the EXCELION 1200 grass cutting brush-cutter. Used and serviced correctly, this
tool will ensure years of satisfaction.
With more than 20 years of experience in portable electric equipment, Pellenc proposes a large
range of Lithium-Ion and Lithium-Polymer powered tools intended for professional use and
designed for maintenance work in green spaces, orchards and vineyards, and cleaning equipment
for public roads.
Pellenc sets the stage for a new generation of tools combining the advantages of cordless electricity with
the power of Lithium-Ion and Lithium-Polymer, designed for intensive, high quality work.
Increasinglyquietandcompact,environmentallyfriendly,economicallyveryprotableandcomplyingwith
evermorestrictspecicationsregardingergonomics,powerandautonomy,Pellenctoolsprovetheirworth
every day, whether in vineyards, orchards or for the maintenance of green spaces and public sectors.
Pellenctoolsaretheworldleaderinthiseld.
Because of the lightweight nature and easy handling of PELLENC tools, users can work better, with less
effort, without noise and faster than with heat-engine powered tools.
A single unique energy source powers PELLENC tools intended for professional use: The Ultra Lithium
Battery. This revolutionary battery is available in several models, with extended work capabilities. Once
purchased, this battery is compatible with most of the Pellenc Green and City Technology range of
products.
«Innovation, ability to listen, quality and environmental friendliness are PELLENC priorities.»
OUR high capacity Ultra Lithium-Ion BATTERIES
PELLENC is the rst and only manufacturer worldwide to propose a whole range of professional tools
for Parks and Gardens, Local Authorities, Golf Courses, Orchards, Vineyards etc. operated using ultra-
high capacity ternary Lithium-Ion batteries.
PELLENC has developed its own Lithium-based technology for the best results in terms of output
power, autonomy, weight and ergonomics. The result is enlightening as the Pellenc Lithium-Ion
technologyisnearlytwicemoreefcientthantheManganeseLithium-Iontechnology.ManganeseLithium-
Ion contains 125 W/kg, while Pellenc Lithium-Ion contains 250 W/kg.
Furthermore, our ultra-high capacity batteries have an ranging from 800 to 1,500 cycles (one cycle
corresponds with a full charge and discharge). Even after hundreds of days of use, the battery still reaches
over 80% of its initial capacity.
Equipped with a patented intelligent system, Pellenc batteries can be charged at any time without
memory effect and without altering their lithium-ion components. They automatically discharge after several
days of non-use in order to be stored risk free for several months.
The ultra-high capacity of Ultra Lithium Batteries guarantees pollution free, odourless and quiet
operation with a record level of autonomy.

4
56_07_011A
Characteristics of the ULTRA LITHIUM BATTERY
- Secure system (patented) guarantees the preservation of your battery in the event of overloading,
discharging or over-heating
- Life system (patented): ensures an optimum service life for your battery by protecting each of the
components individually
- Balance system (patented): guarantees the balancing of the various battery components in order to
optimise balanced operation
- Power system (patented): enables use of the entire range of PELLENC tools within the scope of a
professional activity thanks to the restitution of the battery’s maximum capacity
Advantages of the ULTRA LITHIUM BATTERY
- Environmentally friendly the energy used by PELLENC tools is environmentally friendly and
participates in an initiative towards sustainable development. Compared to equivalent heat engine
powered tools, CO2 emissions are 30 to 90 times lower.
- Power: PELLENC equipment ensures the user has an unequalled power supply of up to 3,000 W.
- Savings: the battery permits up to a full day of work at a derisory total cost.
- Ergonomics: PELLENC tools are very quiet and light, offering unrivalled comfort and optimal working
conditions.
- Cost-effectiveness: the cost of your battery will be recovered in under a year of use (from 135 days).
The return on investment in the battery over its service life is greater than 5,000 € thanks to the savings
on fuel which is not required*.
Compatibility of our batteries with our machines:
All PELLENC multi-function Ultra Lithium Batteries can be used on all of our machines. However, we
recommend the use of batteries according to the tool, in order to achieve an increased optimization of
autonomy, power and weight.
* You use 5L of mixture per day at a price of €1.50 per litre.
Data calculated for the regular use of the ULiB 1100 battery.
For example, a PELLENC ULB 1100 battery is equivalent to over
4700 liters of gasoline and 90 liters of mixture!
INTRODUCTION

5
RECOMMENDED USE OF BATTERIES AND TOOLS ACCORDING TO THEIR POWER AND
AUTONOMY*
*Battery autonomy depends on the tool, the use and the vegetation being worked.
**Autonomy calculated based on the Eco mode
Recommended use
INTRODUCTION
SPECIFIC
BATTERY MULTIFUNCTION BATTERIES
200 400 700 1100 POLY 5 OLIVION
Weight in kg (no harness nor belt) 1.9 3.4 5.5 5.9 3.4 5.5
LIXION Evolution - vineyard
pruning shears 1 to 3 days
LIXION Evolution adaptable - vineyard pruning shears 2 / 6 days 5 days 10 days 3 / 7 days 5 days
TREELION autonomous orchard pruning shears 1 to 2 days TREELION adaptable orchard pruning shears 3 days 4 / 5 days 7 days 3.5 days 4 / 5 days
HELION – hedge trimmer 1/2 day Up to
1 day
Up to
2 days 1/2 day Up to
1 day
OLIVION – olive harvester 2 to 4 hours Up to
1 day
Up to
2 days 3 to 5 hours Up to
1 day
CULTIVION – hoeing machine 2 to 4 hours Up to
1 day
Up to
2 days 3 to 5 hours Up to
1 day
SELION Pole - chainsaw 1 to 3 hours Up to
1 day
Up to
2 days 2 to 5 hours Up to
1 day
SELION M12 - chainsaw 1 to 3 hours Up to
1 day
Up to
2 days 2 to 5 hours Up to
1 day
SELION C20 - chainsaw 1 to 3 hours 3 to 5 hours Up to
1.5 days 2 to 5 hours
EXCELION 1200 – grass-cutting brush cutter 1 hour 2 to 3.5 hours 3 to 5 hours 1 to 2 hours EXCELION 2000 – brush cutter** 2 to 3 hours 3 to 4,5 hours 1 to 2 hours AIRION - blower 1 hour 2 to 3.5 hours 3 to 5 hours 1 to 2 hours

6
53_10_071A
INTRODUCTION
ByusingPELLENCbatteryandmotortechnology,youbenetfromseveraladvantages:
- energy savings
- ease and comfort of use
- free from motor maintenance
- power equivalent to and often higher than combustion engines
- extremelyprotabletools
- lightweight
- no noise pollution or odors
- virtually inexistent carbon emissions
- Immediate start-up, no need for a starter.
PELLENC OFFERS TECHNOLOGY WHICH MAKES THE HEAT ENGINE OBSOLETE
OUR high output MOTORS
As well as Lithium-Ion technology, PELLENC masters the use of another: revolutionary PELLENC
electronic commutation motors.
With these revolutionary motors, PELLENC has effectively rendered the heat engine obsolete. PELLENC
intends to impose its idea of the tool for tomorrow: powerful, light and pollution-free tools.
Furthermore, the PELLENC technology motor is the only electric motor with as much power output with
the added advantage of being small, giving it an ideal weight.Theoutputofthismotorissignicantly
higher than that of traditional direct-current motors with brushes. Friction caused by the brushes
disappears, the output of PELLENC motors is nearly 90 %.
PELLENC motors are Brushless motors.Thismeansthattheirservicelifeistheoreticallyinnite,with
only the service life of the ball bearings limiting the motor’s service life. There is no need for motor
maintenance, as opposed to heat engines.
PELLENC Brushless motors stop completely each time the trigger is pressed, on the contrary to
heatengines.Therefore,soundemissionsareverylowtothebenetoftheuserandhisimmediate
surroundings!
Finally, PELLENC Brushless motors often drive the cutting element directly (no clutch or reduction
gearbox, meaning less noise and wear).Motorcontroliselectronic,asisthepowersupply,meaningthat
noises linked to mechanical part movements are extremely limited.

7
56_10_037B
INTRODUCTION
OUR RANGE OF PRODUCTS
PELLENC Green and City Technology develops new products every year in an aim to meet the
requirements of professionals.
Today, our range of products is growing and our engineers are doing their utmost to create tools, thus
pushing technology advances further.
Our passion is innovation, with an aim to improve the working quality and conditions for professionals by
supplyingacompleterangeofpowerful,lightweight,easy-to-handleandveryprotabletools:
- our blowers operate quietly with power modulation.
- our hedge-trimmers combine comfort and performance.
- our grass-cutting brush cutters are robust and multi-functional.
- our chainsaws are lightweight, powerful and very easy to handle.
- our pruning shears are the most powerful in the world.
- our hoeing machines, which are unique in the world, replace cumbersome rotary hoes.
- ouroliveharvestersareexceptionallyefcient.
- ourvinetyingmachinecombinesefciencyandprotability.
- our batteries have a very high autonomy.
- our mobile solar panel offers the possibility to charge your batteries anywhere.
- Exceptional light output of our autonomous lighting systems.
All of our tools have minimal CO2 emissions and meet the requirements of Local Collectivities or other
associations in terms of a sustainable environment and ecology.
PELLENC is the only company to propose a full range of tools which are 100 % clean and with zero
CO2 emissions thanks to the SOLERION solar panels which can be used to recharge our batteries.

8
26_13_001A
INTRODUCTION
Hedge-trimmer
HELION Universal
Orchard and green space pruning
shears
- 2 hands -
TREELION D45
Grass-Cutting Brush Cutter
EXCELION 1200
Brush Cutter
EXCELION 2000
Chainsaw
SELIONM12
Hoeing machine
CULTIVION
Chainsaw
SELION C20
Chainsaw on pole
SELION Pole or Telescopic
Orchard and
green space pruning shears
TREELIONM45
Hedge-trimmer on pole
HELION Pole or Telescopic
Vineyard pruning shears
LIXION Evolution
Olive harvester
OLIVION Pole or Telescopic
Blower
AIRION
ULiB Battery
200 - 400 - 700 - 1100 -
POLY 5 - OLIVION
Lighting system
LUMENION
Battery converter
Power Convertor 1000 W

9
BILAN CARBONE
INTRODUCTION
Lithium-Ion technology combined with the electric PELLENC motor means that the EXCELION 1200
emits very little CO2 into the atmosphere, giving it the image of a clean tool.
When comparing the direct CO2 emissions of the EXCELION 1200 and a heat-engine powered brush-cutter,
a huge difference can be seen. A heat-engine powered brush-cutter has direct CO2 emissions of over 4.2
tons per year, while the EXCELION 1200 only emits 67 kg.
Using the EXCELION 1200 means reducing direct emissions by approximately 98 % compared to a
heat-engine; that’s 64 times less!
If you recharge PELLENC batteries using our SOLERION solar charger,
direct CO2 emissions are reduced to ZERO
Heat-engine powered brush-
cutter EXCELION 1200 WITH
SOLERION
Direct emission +
production of petrol
Direct emission +
production of electricity Direct emission
Carbon equivalent/
hour
3,532 g CO2/hour 56 g CO2/hour 0 g CO2/hour
Carbon equivalent/
day
21 kg CO2/day 336 g CO2/day 0 g CO2/day
Carbon equivalent/
year
4.2 tons CO2/year 67 kg CO2/year 0 g CO2/year
By using PELLENC tools:
- you considerably reduce greenhouse gas emissions,
- you strongly participate in protecting the environment.
Data: On average, 1 kWh EDF has a carbon equivalent to 90 g of CO2 per kWh in France, covering production and remaining life
(ADEME-France).
1 liter of SP95 unleaded fuel corresponds to a direct carbon emission equivalent of 2,542g CO2/l and a production + direct carbon
emission of 5,518g CO2/l.
Based on: 6 hours of work per day and 200 days of work annually.
“Every type of human activity creates greenhouse gas emissions, whether directly or indirectly. Therefore,
every company, administration or association may quite rightly take an interest in the emissions they
generate.Toenablethemtoact,theyhavetoestablishananalysistondtheirroomformaneuver.The
Bilan Carbone® method is a greenhouse gas (GHG) emissions assessment tool. It uses easily available
data to correctly evaluate your activity in terms of direct or indirectly generated emissions.” (Source:
ADEME-France)
In order to act responsibly, PELLENC has launched an environmentally friendly range of tools with
minimum CO2 emissions, which can be as low as zero thanks to the SOLERION solar charger.
Thanks to the development of its own Lithium-Ion clean technology, PELLENC proposes ultra-high capacity
batteries with a record level of autonomy and power to rival heat motors. In addition, the PELLENC
motor makes the tool exceptionally protable as it consumes very little energy and is unbeatably
lightweight.

10
ENVIRONMENTALPROTECTION
Your equipment comprises numerous materials which can be valorised or recycled. Entrust
these to your reseller or to an approved service centre so that they can be processed.
Allthroughthisuserguideyouwillndadvisorynotesandinformationentitled:REMARK, CAUTION /
WARNING.
A REMARKprovidesadditionalinformation,clariesapointorexplainsasteptobefollowedindetail.
The CAUTION and WARNINGadvisoriesareusedtodeneaprocedurewhich,ifneglectedorincorrectly
performed, may lead to serious damage to the equipment and/or personal injury.
This advisory:
G
indicates that if the procedures or instructions are not complied with, any damage will not
be covered by the warranty and the owner will be responsible for the repair costs.
Safety indications are also given on the tool; they remind you of the safety precautions to be taken. Identify
and read these indications before using the tool. Immediately replace any indications that may become
partially illegible or deteriorated.
Refer to the «SAFETY INDICATIONS» heading in order to identify the location of the safety
indications on the tool.
No part of this manual may be reproduced without the written consent of PELLENC. The technical
characteristics and the illustrations given in this manual are for information purposes and are in no way
contractual.PELLENCreservestherighttomakeanymodicationorimprovementtoitsproductsas
deemed necessary without informing customers already in possession of a similar model. This manual
forms an integral part of the tool and must accompany the tool if it changes hands.
SAFETY INSTRUCTIONS
INTRODUCTION
Comply with the regulations in force in your country as concerns environmental protection
associated with your activity.
You must read THE WHOLE of this user guide before using the tool or before carrying out
servicing operations.
Comply scrupulously with the instructions and illustrations given in this document.
KEEP THESE INSTRUCTIONS
This manual contains important information and operating instructions for the following
tool. Excelion 1200 brush cutter and grass trimmer

11
• The Excelion 1200 grass cutting brush-cutter is a professional tool exclusively intended for cleaning
green spaces (grass, thick weeds, ligneous weeds, brambles and small shrubs).
• The PELLENC company declines responsibility in the event of damage caused by incorrect operation or
use differing from that intended.
• The PELLENC company also declines responsibility in the event of damage caused by the use of non-
original parts or accessories.
SAFETY INSTRUCTIONS
GENERAL SAFETY INSTRUCTIONS FOR THE TOOL
CAUTION Read all the safety measures and all the instructions.
Retain all the safety measures and instructions for later reading.
This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or preliminary instructions by a person responsible for their safety.
Work area safety
a. Keep the work area clean and well lit.
b. Donotuseelectrictoolsinanexplosiveatmosphere,forexampleinthepresenceofammableliquids,
gases or dust.
c. Keep children and persons present away when using the tool.
Electrical safety
a. The plugs of the electric tool must be adapted to the base. Never modify the plug in any way
whatsoever. Do not use adaptors with grounded tools.
b. Avoid any body contact with grounded surfaces such as pipes, radiators, cookers and refrigerators.
c. Do not expose tools to rain or damp conditions.
d. Do not misuse the power cord. Never use the power cord to carry, pull or disconnect the tool. Keep the
power lead away from heat, lubricant, sharp edges or moving parts.
e. When using a tool outdoors, use an extension adapted to outdoor use.
f. If you must use a tool in a damp place, use power supply protected by a residual current device (RCD).
Personal safety
a. Remain vigilant, watch what you are doing and use common sense when using the tool. Do not use a
toolifyouaretiredorundertheinuenceofdrugs,alcoholormedication.
b. Wear safety equipment. Always wear eye protection.
c. Avoidanyuntimelystartingofthedevice.Makesuretheswitchisintheoffpositionbeforeconnecting
the tool to the mains and/or battery pack, picking it up or carrying it.
d. Remove any adjustment key before starting the tool.
e. Do not rush. Adopt a suitable position and remain balanced at all times.
f. Wear appropriate clothing. Do not wear loose clothing or jewellery.
g. Keep hair, clothing and gloves away from moving parts.
h. If systems are provided to connect dust extraction and recovery equipment, make sure these systems
are connected and properly used.
KEEP THESE INSTRUCTIONS

12
SAFETY INSTRUCTIONS
Tool usage and maintenance
a. Do not force the tool. Use a tool suited to your application.
b. Do not use the tool if the switch does not allow it to be switched on and off.
c. Disconnect the plug of the power supply source and/or battery pack from the tool prior to any
adjustment, change of accessories or before putting the tool away.
d. When not in use, keep tools out of reach of children, and do not allow persons to use the tool if they do
not know how to use it and if they have not read these instructions.
e. Comply with tool servicing instructions. Check that the moving parts are not misaligned or jammed, that
there are no broken parts or that there is no other condition which could affect the operation of the
tool. In the event of damage, have the tool repaired before using it.
f. Keep the cutting components sharp and clean.
g. Use the tool, accessories, blades etc., in accordance with these instructions, taking into account the
working conditions and the work to be performed.
Use of battery-operated tools and usage precautions.
a. Onlyrechargeusingthechargerspeciedbythemanufacturer.
b. Onlyusethetoolswithspecicallydesignatedbatterypacks.
c. When a battery pack is not used, store it away from other metal objects such as paper clips, coins, keys,
nails, screws or other small items which can form a connection from one terminal to another.
d. In poor conditions, liquid can be ejected from the battery; avoid any contact. In the event of accidental
contact, clean with water. If the liquid gets into your eyes, seek medical help.
Maintenance and upkeep
a. Havethetoolservicedbyaqualiedrepairerusingonlyidenticalspareparts.
SAFETY WARNINGS FOR THE EXCELION 1200 BRUSH CUTTER AND GRASS TRIMMER
1– Do not use the metal cutting tools near walls, fences, tree trunks, rocks or other similar obstacles. Contact
with these types of elements can cause a rebound effect, increase the risk of ricochets and damage the
cutting tool. Pellenc recommends using Pellenc cutting wires for these work situations.
Never use the Excelion 1200 brush cutter and grass trimmer with one hand only.
2– Always use the machine with the cutting head parallel to the ground. The safety guard no longer provides
sufcientprotectioniftheangleofthecuttingheadisexcessive,whichislikelytoincreasetheriskofinjury.
3– Stop the Excelion 1200 brush cutter and grass trimmer immediately if the cutting tool starts responding
differently (different noise, increased vibrations). Check that the cutting tool is properly attached and verify
itscondition(nodistortion,sufcientlysharp).Replaceanydamagedcuttingtoolasitcanexplodeand
cause serious, even fatal injuries.
4– CAUTION: The cutting tool continues rotating for a few seconds after the control trigger has been released.
Always keep your hands and feet clear of the rotating cutting tool.
5– Cutting wire
• Never remove the blade installed in the safety guard as it trims the wire to the appropriate length.
• Neverusemetalwireoranyothermaterialinsteadofthenyloncuttingwire.Metalwireislikelytobreak
and be projected, causing serious injuries.
• Only use nylon cutting wire recommended by Pellenc with a max. diameter of 3 mm.
6– Cutting blades
Always use an original Pellenc cutting tool.

13
56_10_016A
53_13_070A
SAFETY MEASURES FOR THE CHARGER AND THE BATTERY
Refer to the Pellenc tools battery manual.
SAFETY INSTRUCTIONS
TRANSPORTING THE EXCELION 1200 GRASS CUTTING BRUSH-CUTTER
1– Keep the original packaging in order to be able to pack the Excelion 1200 grass cutting brush-cutter in
the event of sending it for an overhaul or repair.
2– Do not carry the machine or the battery by the power cord.
3– Always release the control trigger to stop the electric motor and ensure that the cutting tool is no longer
moving before placing the machine on the ground.
4– Place metal cutting tool(s) in their original packaging, or in their transport bag.
5– Replace the battery in its original packaging.
6– Block the machine and battery correctly in the transport vehicle.
STORING THE EXCELION GRASS CUTTING BRUSH-CUTTER
• Keep the original packaging to store the machine.
• Store the machine in a dry place out of the reach of children.
• Lubricate the output shaft during prolonged storage.
WARNING:
Before working on the tool, check that the On / Off switch is in the
off position «0» and disconnect the battery power lead.

14
53_13_092A
1
3
2
4
5
6
7
8
9
10
1 5
2 6
37
48
SAFETY MEASURES
SAFETY EQUIPMENT
SAFETY INSTRUCTIONS
Protective equipment Wearing is
1 Helmet Mandatory
2 Visor Recommended/advised
3 Hard-wearing gloves Mandatory
4 Safety footwear Mandatory
5 Ear protection Mandatory
6 Safety goggles Mandatory
7 Safety jacket or over-sleeves Recommended/advised
8 Work trousers RMandatory
SAFETY INDICATIONS
1– Noise level
91 dB acoustic power, 78 dB acoustic pressure
2– Read the user manual
Read the notice carefully and comply with the safety measures.
3– Goggles and an approved safety helmet must be worn
Pellenc advises wearing a face shield.
4– Wearing gloves, safety trousers and safety shoes is mandatory
5– Safety distance to be respected
Respect the 15 m safety distance and ensure nobody (particularly children) or animals are within the
machine's working space.
Stop the machine immediately if a person or animal approaches.
6– Rotation direction and maximum rotation speed (6,200 rpm)
Pay attention to the grass cutting brush-cutter's rotation direction. This is indicated on the safety casing.
7– Beware of projections
8– Beware of kickback
Avoid all contact between the blade and solid objects.
9– Risk of burns
Do not touch the motor casing or the electronic motor control board's radiator during or after use of the
machine.
10– Do not expose to or work in the rain.

15
1 2 3 54 6 7 8
9
10111213
53_13_093A
14
15
DESCRIPTION AND TECHNICAL CHARACTERISTICS
Grass Cutting Mode
The Excelion 1200 grass cutting brush-cutter can be used according to 2 modes of use:
- the Grass Cutting mode, with cutting line,
- the Brush Cutting mode, with steel blades, which requires additional safety elements.
Description of the main elements:
1– Handle : For guiding the Excelion 1200 grass cutting brush-cutter
2– Safety trigger : Prevents the control trigger from being accidently pressed, the safety trigger must be
pressed in order to press the control trigger
3– Cutting tool max. rotation speed switch and display panel : Used to select the maximum cutting speed
which is indicated on the display panel.
4– Front handle : For guiding the machine, the handle's position on the telescopic tube is adjustable
5– Telescopic tube locking grip : Enables the telescopic tube's length to be adjusted
6– Telescopic tube
7– Telescopic tube support : Articulates with the motor casing, enabling the cutting head's angle to be
adjusted
8– Motor casing : Protects the electric motor and evacuates heat. Articulates with the telescopic tube
support enabling the cutting head's angle to be adjusted
9– Safety casing : Preventstheriskoftheoperatorbeinghitbyyingobjects(stones,bitsofmetal).
A cutter attached to the safety casing ensures the cutting line is at the right length
10– Front handle adjuster knob : Adjusts the position of the front handle on the telescopic tube
11– Electronic motor control board and its radiator : Protects the electronic control board and evacuates
the heat.
12– Control trigger : Used to actuate the rotation of the cutting tool according to a progressively adjustable
speed.
13– Electric cord : Connects the machine to the Pellenc tools battery.
14– Distancing device : MandatorysafetyelementforBrushCuttingmode.Reducestheriskofcutstothe
operator’s legs and feet, by maintaining a safe distance between vibrator rake and operator.
Interchangeable part for a right-handed person or a left-handed person.
15– Carrying eye : MandatorysafetyelementforBrushCuttingmode.Attachesthemachinetothe
operator's safety vest via a harness

16
DESCRIPTION AND TECHNICAL CHARACTERISTICS
TECHNICAL CHARACTERISTICS
Excelion 1200
Model Version
MULTI-CUT
Lawnmower
Version
MULTI-CUT
Two-pronged blade
Power 1,200 W
Weight (without cutting tool and safety casing) 3.8 Kg 3.9 Kg
Dimensions (L x w x H) in mm 1360 x 85 x 210 1360 x 85 x 210
Cutting diameter 300 mm 230 mm
Rotation speed 2,000 to 6,200
Working capacity (time) According to use and battery type
Vibration emission value as per EN 60745-1, EN ISO 22867.
handle
ah≤2,5m/s²
uncertainty
Kd =1,5m/s²
Determining the sound levels and vibration rates is based on the operating conditions at the maximum nominal rating.
Symbol Value Unit Reference Comment
LWAm 90 dB(A) 1 pW Measuredsoundpowerlevel
LWAg 91 dB(A) 1 pW Guaranteed sound power level
The recording of the measured sound power level and of the guaranteed sound power level has been performed according to a
procedure in accordance with directive 2000/14/CE appendix V.
MaximumA-weightedsoundpressurelevel(ref.20µPa)atthepositionoftheuser LpA = 83 dB(A) K = 2,5 dB(A)
C-weightedpeaksoundpressure(ref.20µPa)atthepositionoftheuser LpC < 130 dB(C)
ValuesdenedaspersoundmeasurementstandardsNFENISO11201andNFENISO3744.
REMARK:
Safety element assembly/disassembly procedures only require the adjustment key supplied with the
Excelion 1200 grass cutting brush-cutter.
The cutting head assembly/disassembly procedures require circlip pliers (not supplied).
Consultthe"Maintenance"sectiontondthePellencpartnumbersforpartstobereplaced(seepage30).
PREPARING THE MACHINE FOR USE

17
53_10_080B
3
1
2
1
53_10_096A
2
34
1
53_10_081B
2
34
1
53_13_094A
3
1
2
ASSEMBLY/DISASSEMBLY OF THE FRONT HANDLE
ASSEMBLY/DISASSEMBLY OF THE CARRYING EYE AND THE DISTANCING DEVICE
Clearance device for a right-handed person. Clearance device for a left-handed person.
ASSEMBLY/DISASSEMBLY OF THE SAFETY CASING

18
53_10_089A
53_10_090B
ADJUSTING THE WORKING POSITION
• Unlock the front handle adjuster knob.
Adjusting the position of the front handle adjusts the grass cutting brush-cutter's "horizontal position", so
that it is within reach and the cutting head makes slight contact with the ground. The elbow should not be
bent.
(This adjustment is performed at the same time as the adjustment of the harness length.)
ADJUSTING THE POSITION OF THE FRONT HANDLE
Before every use, the Excelion 1200 grass cutting brush-cutter's working position must be adjusted
according to the size of the operator. This enables operating comfort requiring little effort from the operator.
Adjusting the machine's working position according to the size of the operator consists in four steps:
- adjustment of the front handle position,
- installation of the harness and adjustment of its length,
- adjustment of the tube length,
- adjustment of the cutting head orientation.
These various adjustments are repeated until the brush cutter is in an adequate working position.
These various adjustments are repeated until the brush cutter and grass trimmer is in a suitable working
position.
• Slide the front handle along the telescopic tube until it
is a suitable position.
• Lock the front handle adjuster knob to block the
handle's position on the machine.
ADJUSTING THE WORKING POSITION

19
2
3
4
1
5
6
53_13_138A
PREPARING THE MACHINE FOR USE
ATTACH AND ADJUST THE LENGTH OF THE HARNESS,
THE HARNESS (
supplied with the tool
)
Adapting the length of the harness helps adjust the "vertical position" of the brush cutter so that it is within
reach and the cutting head is pointing slightly downwards.
(This adjustment is made at the same time as the balance adjustment and the orientation of the handlebar).

20
48_11_013A
53_10_023A
53_10_059A
ADJUSTING THE WORKING POSITION
Adjusting the length of the telescopic tube enables the correct swing radius to be obtained according to the
size of the operator or the working environment.
ADJUSTING THE LENGTH OF THE TELESCOPIC TUBE
• Unlock the locking grip by turning it counter-clockwise.
• Adjust to the desired telescopic tube length.
• Lock the locking grip.
Adjusting the cutting head orientation enables the cutting head to be aligned with the ground. The cutting
head should touch the ground slightly.
ADJUSTING THE CUTTING HEAD ORIENTATION
• Unlock the motor casing knob.
• Adjust the cutting head so that it is parallel with the
ground.
• Lock the motor casing knob to block the cutting head
in position.
Cutting head adjustment
range