Pentair INTELLITOUCH User manual

INTELLITOUCH®CONTROL SYSTEM
FOR POOL AND SPA
IMPORTANT SAFETY INSTRUCTIONS
READ AND FOLLOW ALL INSTRUCTIONS
SAVE THESE INSTRUCTIONS
USER’S GUIDE

© 2011Pentair Water Pool and Spa, Inc. All rights reserved
1620 Hawkins Ave., Sanford, NC 27330 • [phone]
10951 West Los Angeles Ave., Moorpark, CA 93021 • [phone]
IntelliTouch®, MagicStream®, ScreenLogic®, IntelliChlor®, IntelliFlo®, SpaCommand™, MobileTouch®, QuickTouch®,
IntelliBrite®, SAm®, SAL®, FIBERworks®, Amerlite®, SpaBrite®, Photon Generator®, UltraTemp®, IntelliChem®,
Pentair Pool Products®, and Pentair Water Pool and Spa® are trademarks and/or registered trademarks of Pentair Water
Pool and Spa, Inc. Aqua Rite® is a registered trademark of Hayward Industries, Inc. AutoClear® is a registered trademark
of Zodiac Pool Care. Crestron® is a registered trademark of Crestron Electronics. Liton® is registered trademark of Eema
Industries, Inc. and Pool Pilot® is a registered trademark of Autopilot Systems Inc. Unless noted, names and brands of
others that may be used in this document are not used to indicate an affiliation or endorsement between the proprietors of
these names and brands and Pentair Water Pool and Spa, Inc. Those names and brands may be the trademarks or
registered trademarks of those parties or others.
P/N 521075 Rev A 05/31/11

i
IntelliTouch®Control System User’s Guide
Contents
Important Warning and Safety Instructions..................................................................................................... v
In this User’s Guide..............................................................................................................................................vi
Technical Support..........................................................................................................................................vi
RelatedIntelliTouch Manuals .........................................................................................................................vi
SECTION 1 - INTELLITOUCH SYSTEM OVERVIEW ....................................................................................... 1
Introduction .......................................................................................................................................................... 1
IntelliTouch System Overview.............................................................................................................................. 1
In the home.................................................................................................................................................... 1
Around the pool ............................................................................................................................................. 1
At the equipment pad..................................................................................................................................... 1
IntelliTouch in your home ............................................................................................................................... 3
IntelliTouch System Components......................................................................................................................... 4
Load or Power Center .................................................................................................................................... 4
IntelliTouch Personality Kits........................................................................................................................... 4
IntelliTouch Personality Kit Contents ............................................................................................................. 4
ScreenLogic Interface Kits................................................................................................................................... 5
OptionalEquipment (IntelliChem)......................................................................................................................... 5
iPhone/iPad Touch Inteliface Kit (P/N 520500) ............................................................................................. 6
In-Wall Touch Screen (iTC35 Kit - P/N 520502) ............................................................................................ 6
Digital Wireless Tablet (iTC45 Kit - P/N 520503) ........................................................................................... 6
IntelliTouch ScreenLogic Interface Accessory Kits.............................................................................................. 6
SECTION 2 - OPERATING THE INTELLITOUCH SYSTEM............................................................................. 7
Main Screen (Indoor Control Panel and MobileTouch wireless control panel)...................................................... 7
IntelliTouch Menus................................................................................................................................................ 8
IntelliTouch Indoor Control Panel Menus ....................................................................................................... 9
Heating your Spa and Pool................................................................................................................................. 10
Adjust Spa or Pool Heat Settings ................................................................................................................ 10
Selecting the Heating System ..................................................................................................................... 11
Switching on Lights Manually ............................................................................................................................. 12
Special Lighting Features................................................................................................................................... 13
Dimming Lights................................................................................................................................................... 14
Setting ON/OFF Times for Equipment (PROGRAM)......................................................................................... 14
Smart Start (Setting up SAm, SAL and IntelliBrite lights)............................................................................ 15
Using the Once Only Timer......................................................................................................................... 16
Setting the Egg Timer Function ................................................................................................................... 17
iS10 Spa-Side Remote Controller ...................................................................................................................... 18
iS4 Spa-Side Remote Controller ........................................................................................................................ 19
MobileTouchWireless Controller ........................................................................................................................ 19
Charging the MobileTouch Wireless Controller............................................................................................ 20
Using the MobileTouch Wireless Controller ................................................................................................. 20
QuickTouch Wireless QT4 Remote Controller ................................................................................................... 21
IntelliChlor Salt Chlorine Generator (Accessory) ............................................................................................... 21
IntelliFlo VF 3050 Variable Flow Pump (Accessory)........................................................................................... 22
IntelliFlo VS 3050Variable Speed Pump (Accessory)........................................................................................ 22
IntelliFlo VSF+SVRS Variable Speed Pump (Accessory) .................................................................................. 22

IntelliTouch®Control System User’s Guide
ii
Contents (Continued)
SECTION 3 - PREPARING THE SYSTEM FOR INITIAL START-UP ............................................................. 23
Setting up the IntelliTouch System ..................................................................................................................... 23
Wired Controllers (Automatically Enabled)......................................................................................................... 25
Adding Multiple SpaCommand) Spa-Side Remotes and Expansion Centers .................................................... 25
Adding a MobileTouch Wireless Controller ......................................................................................................... 25
Manually Enabling Expansion Centers........................................................................................................ 26
Assigning Additional Expansion Centers .................................................................................................... 27
Setting up the MobileTouch Wireless Controller ................................................................................................. 28
Adding a SpaCommand Spa-Side Remote ........................................................................................................ 30
Prepare the System for Operation ..................................................................................................................... 31
Checking the Main Load Center.................................................................................................................. 31
Setting up the IntelliTouch System using the Indoor Control Panel or MobileTouch .................................... 33
The Preference Screen Options.................................................................................................................. 33
Set the System Clock ................................................................................................................................. 34
Assigning Circuit Names (for Display 1, 2, 3, and 4) .................................................................................. 34
Selecting DISPLAY Screen 1, 2, 3, or 4...................................................................................................... 35
Assigning Circuit Names.................................................................................................................................... 35
Selecting the Display Screens ........................................................................................................................... 36
IntelliTouch Circuit Names.................................................................................................................................. 37
Creating Custom Names for Auxiliary Circuits .................................................................................................. 38
Assign Circuit Functions and Freeze Protection................................................................................................ 39
Freeze Protection............................................................................................................................................... 39
Assigning a function and freeze protection to a circuit....................................................................................... 39
Special Functions for Circuits ............................................................................................................................ 41
Setting up Lighting Options (Color Swim and Color Set).................................................................................... 42
Color Swim and Color Set ........................................................................................................................... 42
Setting up Color Swim and Color Set with SAm, SAL, or FIBERworks ...................................................... 42
Setting up Color Swim and Color Set lights................................................................................................. 42
Setting up IntelliBrite LED lights ......................................................................................................................... 46
Selecting IntelliBrite Modes ......................................................................................................................... 48
Modes screen ......................................................................................................................................... 48
Modes: Color light shows ........................................................................................................................ 48
Feature: Swim ............................................................................................................................................. 48
Feature: Color set........................................................................................................................................ 49
Fixed Colors Screen ................................................................................................................................... 49
Fixed Colors: Hold/Recall Feature .............................................................................................................. 49
Setting up MagicStream Laminars ..................................................................................................................... 50
Using the MagicStream Laminar Features..................................................................................................... 52
Setting up Equipment (from the Equipment Screen) .......................................................................................... 53
Manual Priority Override of Timed Program Circuits.......................................................................................... 53
Chlorine Generator............................................................................................................................................. 54
Activating the Chlorinator ............................................................................................................................... 54
Adjusting the Chlorine Output Level............................................................................................................... 54
Super Chlorinate the Pool Water..................................................................................................................... 55
IntelliFloVF 3050, VS 3050 andVSF+SVRS Pump Setup................................................................................. 56
Setting up IntelliFlo ........................................................................................................................................ 56
How many pumps will IntelliTouch support? ................................................................................................. 56
Connecting power to an IntelliFlo pump......................................................................................................... 56
Assigning an IntelliFlo VF 3050 pump address ............................................................................................. 56

iii
IntelliTouch®Control System User’s Guide
Contents (Continued)
IntelliFlo Menu Options....................................................................................................................................... 57
IntelliFlo pump type and assignment screens .................................................................................................... 57
IntelliFloVF 3050 Pump Setup ....................................................................................................................... 58
IntelliFlo Set Parameters screens .............................................................................................................. 58
Assign or change a pump circuit name .................................................................................................. 58
Filtering parameters.................................................................................................................................... 59
Priming parameters .................................................................................................................................... 60
Backwash parameters ............................................................................................................................... 61
Vacuum parameters ................................................................................................................................... 62
Assign custom flows .................................................................................................................................. 63
IntelliFlo status screen ............................................................................................................................... 64
IntelliFloVS 3050 and VSF+SVRS Pump Setup ............................................................................................ 65
Setting up IntelliFlo VS 3050 and VSF+SVRS............................................................................................ 65
Assigning an IntelliFlo VS 3050 pump address .......................................................................................... 65
Assigning an IntelliFlo VSF+SVRS pump address..................................................................................... 65
Setting up an IntelliFloVS 3050 and VSF+SVRS pump from Equipment Screen ...................................... 66
Priming Parameters (IntelliFloVS 3050)..................................................................................................... 67
Assign custom speeds (RPM) IntelliFlo VS 3050) ..................................................................................... 68
Assign custom speeds (RPM/GPM) IntelliFlo VSF+SVRS........................................................................ 69
IntelliFlo VS 3050 and IntelliFloVSF+SVRS4 Status Screen..................................................................... 71
Setting up an UltraTemp Heat Pump .................................................................................................................. 72
UltraTemp heat pump screen (HEATPUMPCOM) ......................................................................................... 72
Setting up IntelliChemWater Chemistry Controller ............................................................................................ 73
Setup Solar Equipment and Heat Pump Option ................................................................................................. 74
Setting up solar equipment ............................................................................................................................. 74
Setting up a heat pump and gas heater.......................................................................................................... 74
Setting up a 2-Speed Pump ............................................................................................................................... 75
Delay for Valves and Pumps (Heater Cool-Down Cycle) .................................................................................. 75
Delay Cancel Feature ........................................................................................................................................ 76
Spa Options ....................................................................................................................................................... 77
Set Automatic Spa Heating When the Spa is Manually Switched On ............................................................ 77
Freeze Override (30-240 minutes) ................................................................................................................. 77
Changing the Display to Show Fahrenheit to Celsius ........................................................................................ 77
Configuring Valve Actuators (Controlled by AUX or Feature Circuit) ................................................................. 78
Feature Circuits.................................................................................................................................................. 79
Assign a Circuit Name to a Feature Circuit........................................................................................................ 79
Creating a Macro Circuit .................................................................................................................................... 80
Configuring Remote Control Button Circuits
(iS4, SpaCommand, Spa Side Remtoe, QT4 QuickTouch, and Phone Remote)......................................... 81
Setting up the Remote ControlTelephone Feature............................................................................................. 82
Disable/Enable Spa-Side Remote...................................................................................................................... 83
Keypad Lock ...................................................................................................................................................... 83
SECTION 4 - SERVICE AND MAINTENANCE ............................................................................................... 84
CalibratingTemperature Sensors ....................................................................................................................... 84
Using the Service Personnel Screen ................................................................................................................. 85
Checking Firmware Version ............................................................................................................................... 85
Manually Updating Between Indoor and Outdoor Control Panels ...................................................................... 86
Erasing the System Memory.............................................................................................................................. 87
System Worksheet Overview ............................................................................................................................ 88

IntelliTouch®Control System User’s Guide
iv
Contents (Continued)
SECTION 4 - SERVICE AND MAINTENANCE (Continued)
Main Outdoor Control Panel ............................................................................................................................... 95
Shared Equipment Systems Model i5+3, i7+3, i9+3 .................................................................................... 95
Single Body Systems Model i5S+3, i9+3S................................................................................................... 96
Dual Body Dual Equipment Systems Model i10+3....................................................................................... 96
Expansion Centers Model i5x, i10x.............................................................................................................. 96
Erasing outdoor Contrl Panel Memory (Factory Default).................................................................................... 97
SECTION 5 - TROUBLESHOOTING ............................................................................................................... 98
System Start-Up ................................................................................................................................................ 98
Check Electronics.......................................................................................................................................... 98
System Test.................................................................................................................................................... 98
Troubleshooting .................................................................................................................................................. 99
Frequently Asked Questions (FAQ)................................................................................................................... 99
What does a‘+3’IntelliTouch system mean? .................................................................................................. 99
How Do I Setup/Configure/Program the 2-Speed Pump? .............................................................................. 99
Can I turn the Heater On and Change the temperature from the Spa? .......................................................... 99
How do I get Solar to switch on?.................................................................................................................... 99
What are Color Swim and Color Set?........................................................................................................... 100
How do I get SAm/SAL/PG2000 to Synchronize? ....................................................................................... 100
Can I copy a standard configuration to all the systems I install? ................................................................. 100
Fixing mismatched system personalities ..................................................................................................... 101
Indoor Control Panel and Outdoor Control Panel Connection Problem ........................................................ 101
MobileTouch Temperature Readout Not Accurate (20 to 30 Degrees off) .................................................... 101
System Problem Diagnosis.............................................................................................................................. 102
Problem:The system works in Service Mode, but Indoor Control Panel fails to operate. ............................ 102
Problem: Indoor and Outdoor Control Panels work, but iS4 fails to operate................................................ 103
Problem: Indoor and Outdoor Control Panels work, but iS10 fails to operate.............................................. 104
Problem: The Mobile Control Panel will not work, or will not work dependably. ........................................... 105
Problem: The Quick Touch remote will not work, or will not work dependably............................................. 106
IntelliFlo Alerts andWarnings ........................................................................................................................... 108
Suction Blockage ......................................................................................................................................... 108
IntelliFloVS 3050 and IntelliFloVSF+SVRS Warning and Alarm Conditions................................................... 109
Alarm and warning LED sequence............................................................................................................... 109
IntelliTouch Power CenterWiring Diagram ....................................................................................................... 110
IntelliTouch Load CenterWiring Diagram ......................................................................................................... 111
Wiring IntelliTouch to a Salt Chlorine Generator ............................................................................................... 112
Wiring UltraTemp to IntelliTouch ....................................................................................................................... 112
Glossary.......................................................................................................................................................... 113

v
IntelliTouch®Control System User’s Guide
Important Notice:
Attention Installer: This manual contains important information about the installation, operation and
safe use of this product.This information should be given to the owner and/or operator of this equipment.
WARNING - Before installing this product, read and follow all warning notices and instructions
which are included. Failure to follow safety warnings and instructions can result in severe injury, death,
or property damage. Call [phone] for additional free copies of these instructions.
DANGER - Water temperature in excess of 100° F (37.7° C) may be hazardous to your health.
Prolonged immersion in hot water may induce hyperthermia. Hyperthermia occurs when the
internal temperature of the body reaches a level several degrees above normal body
temperature of 98.6° F (37° C.). Effects of hyperthermia include: (1) Unawareness of
impending danger.(2) Failure to perceive heat.(3) Failure to recognize the need to leave the
spa. (4) Physical inability to exit the spa. (5) Fetal damage in pregnant women. (6) Unconsciousness
resulting in danger of drowning.The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia in hot tubs and spas.
WARNING - To reduce the risk of injury, do not permit children to use this product unless they are
closely supervised at all times.
WARNING - The use of alcohol, drugs, or medication can greatly increase the risk of fatal
hyperthermia in hot tubs and spas.
WARNING - GAS HEATER: The IntelliTouch® automation control system is designed to supply high voltage
(120VAC / 240VAC) to a gas heater and override the thermostat in the heater’s control circuit.This automation
control system is intended to control gas heaters with a high temperature limit switch(s) safety circuit ONLY.Failure
to do so may cause property damage or personal injury.
WARNING - Do not use this product to control an automatic pool cover. Swimmers may become
entrapped underneath the cover.
WARNING - For units intended for use in other than single-family dwellings, a clearly labeled
emergency switch shall be provided as part of the installation. The switch shall be readily accessible to
the occupants and shall be installed at least (5) feet (1.52 m) away, adjacent to, and within sight of, the
unit.
CAUTION - Except for listed spa-side remote controls, install a minimum of five (5) feet (1.52 m)
from the inside wall of the pool and spa.
CAUTION - This product is intended for use in swimming pool applications only.
Two Speed Pump Controls Notice (Title 20 Compliance)
Please read the following important Safety Instructions (See page 75 pump speed setup)
When using two-speed pumps manufactured on or after January 1, 2008, the pump’s default
circulation speed MUST be set to the LOWEST SPEED, with a high speed overide capability being
for a temporary period not to exceed one normal cycle, or two hours, whichever is less.
IMPORTANT WARNING AND SAFETY INSTRUCTIONS

IntelliTouch®Control System User’s Guide
vi
FCC Regulatory Safety Notice -The MobileTouch wireless control panel devicehasbeentestedandfound
to comply with the liFCC Standard - 47 CFR Part 15, Subpart C (Section 15.247).This version is limited to
chapter 1 to chapter 11 by specified firmware controlled in the U.S.A.
Canada - Industry Canada (IC) -The IntelliChlor devicecomplieswithRSS210ofIndustry Canada.(1999).
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this
device must accept any interference, including interference that may cause undesired operation of the device.
Instruction to user -The IntelliChlor device has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules.These limits are designed to provide reasonable protection
against harmful interference in a residential installation. The IntelliChlor device generates, uses and can radiate
radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful
interference to radio communications.However, there is no guarantee that interference will not occur in a
particular installation.If this device does cause harmful interference to radio or television reception, which can
be determined by switching the device off and on, the user is encouraged to try to correct the interference by
oneormoreofthefollowingmeasures:
• Reorientor relocate the receiving antenna.
• Increasethe separation betweenthe equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
• Consultthedealer or an experienced radio/TV technician for help.
General Installation Information
1. All work on the IntelliTouch® load/power center must be performed by a licensed electrician, and must
conform to all national, state, and local codes.
2. Install to provide drainage of compartment for electrical components.
3. If this system is used to control underwater lighting fixtures, a ground-fault interrupter (GFCI) must be
provided for these fixtures. Conductors on the load side of the ground-fault circuit-interrupter shall not
occupy conduit, junction boxes or enclosures containing other conductors unless such conductors are
also protected by a ground-fault circuit-interrupter.Refer to local codes for details.
4. A terminal bar stamped is located inside the supply terminal box.To reduce the risk of electric
shock, this terminal must be connected to the grounding means provided in the electric supply service
panel with a continuous copper wire equivalent in size to the circuit conductors supplying this
equipment (no smaller than 12 AWG or 3.3 mm).The bonding lug(s) provided on this unit are intended
to connect a minimum of one No.8 AWG for US installation and two No.6 AWG for Canadian
installations solid copper conductor between this unit and any metal equipment, metal enclosures or
electrical equipment, metal water pipe, or conduit within 5 feet (1.5 m) of the unit.
5. The electrical supply for the IntelliTouch® load/power center must include a suitably rated switch or
circuit breaker to open all ungrounded supply conductors to comply with in accordance with the
National Electrical Code (NEC), NFPA 70 or the Canadian Electrical Code (CEC), CSA C22.1.All
applicable local installation codes and ordinances must also be adhered to.The disconnecting means
must be readily accessible to the tub occupant but installed at least 10 ft. (3.05 m) from the inside wall
of the pool.
6. GAS HEATER: The IntelliTouch® automation control system is designed to supply high voltage (120
VAC / 240 VAC) to a gas heater and override the thermostat in the heater’s control circuit.This
automation control system is intended to control gas heaters with a high temperature limit switch(s)
safety circuit ONLY.Failure to do so may cause property damage or personal injury.
6. Supply conductor for the IntelliTouch® load/power center must be sized to support all loads.Maximum
supply conductor current must be 150 Amps at 120VAC / 240 VAC.
IMPORTANT WARNINGS AND SAFETY PRECAUTIONS
(CONTINUED)
IMPORTANT WARNING AND SAFETY INSTRUCTIONS
For information about the Virginia Graeme Baker Pool and Spa Safety Act, contact the Consumer Product Safety
Commissionat [phone] or visit www.cpsc.gov.
NOTE: Always turn off all power to the pool pump before installing the cover or working on any suction outlet.

vii
IntelliTouch®Control System User’s Guide
BlankPage

IntelliTouch®Control System User’s Guide
viii
In this User’s Guide
ThisUser’sGuidedescribeshowtooperate the IntelliTouch®pooland spa control system.
Thismanualconsistsofthefollowingsections:
Section 1:IntelliTouch System Overview (page1)
Section 2:Operating the IntelliTouch System (page7)
Section 3:Preparing the System for Initial Start-Up (page23)
Section4:Service and Maintenance (page81)
Section5:Troubleshooting (page95)
Technical Support
Sanford, North Carolina (8 A.M. to 5 P.M. ET.)
Moorpark, California (8 A.M. to 5 P.M. PS.)
Phone: [phone]
Fax: [phone]
Web sites
http://www.pentairpool.com andstaritepool.com
Download the IntelliTouch User’s Guide (PDF) from theWeb
Related IntelliTouch Manuals
IntelliTouchPersonality Kit User’sGuide (P/N521074)
IntelliTouch Load Center and PowerCenterInstallationUser’sGuide (P/N521139)
IntelliTouch i-Link Protocol InterfaceAdapter User’s Guide (P/N520450)
ScreenLogic®User’sGuide (P/N520493)
ScreenLogic®Video & LightingProtocolAdapterUser’sGuide (P/N520936)
IntelliChlorInstallation and User’s Guide (P/N520589)
IntelliChemInstallation and User’sGuide (P/N521363)
http://www.http://www.pentairpool.com/pdfs/IntelliTouchUG.pdf

IntelliTouch®Control System User’s Guide
1
Section 1
IntelliTouch®Control System Overview
Introduction
Welcome! Your IntelliTouch®Control System for Pool and Spa will change the way you view pool
and spa controls. This innovation in pool and spa automation offers complete freedom for you
while having full automation control over your pool, spa, lights, heater, pump, cleaners and much
more. You can now schedule multiple start and stop times to control your lights, heater, spa jets, and
lter pumps. Using the IntelliTouch®Indoor Control Panel or IntelliTouch MobileTouch®Wireless
Controller you can control your pool, spa, and lights from anywhere inside or outside or your home.
Optional controllers are also available such as the wireless Digital Tablet, iPhone, iPad or iPod
Touch interface (purchased separately), and in-wall Touch Screen that can interface with your PC.
IntelliTouch is a scalable system that can be upgraded to a completely integrated home automation
solution including audio, security, climate, irrigation and more. For more information about using
these interfaces, refer to the ScreenLogic®2 Interface Kits on page 5.
IntelliTouch Control System Overview
An IntelliTouch control system can include ve (5) to 40 high voltage relays circuits that can be used
to control any combination of pumps, lights, water features. A maximum of ten (10) relays can be
housed in an IntelliTouch control system Load Center or Power Center. Up to three (3) Load Centers
or Power Centers can be connected to a main Load Center for a maximum of 40 relays. User-
congurable circuits can be used to control equipment. The “Feature Macro” circuits feature allows
any number of circuits to be combined and controlled by a single button. An optional IntelliTouch
control system Dimmer Module (P/N 520406) can be installed for use to dim any high voltage
incandescent light such as Pentair Amerlite®and Pentair SpaBrite®Lights. The dimmer module
supports multiple lights from 100 watts up to 1,000 watts and installs in a standard relay location.
Any number of dimmers (up to 10 maximum) may be used with a maximum combined load of 4,000
watt in a single Load Center.
In the home
The IntelliTouch control system can utilize multiple wired and wireless controllers including the
Digital Tablet, iPhone or iPad Touch interface (purchased separately), the wired in-wall Touch
Screen, Indoor Control Panel, and the wireless MobileTouch® Wireless Controller. Your existing
home PC can also be used to control the IntelliTouch system via the ScreenLogic®Interfaces. A
maximum of four ScreenLogic2 interfaces can be used, for example, four Tablets or four in-wall
Touch Screen’s, or four PC’s in any combination.
Around the pool
The IntelliTouch control system, SpaCommand® Spa-Side Remote and iS4 Spa-Side Remote provide
control buttons for various pool and spa functions. The SpaCommand spa-side remote also provides
a temperature display.
At the equipment pad
The pool pump, lter, and various IntelliTouch control system remote controllers and interfaces are
connected to the IntelliTouch control system Load Center and/or Power Center enclosure which
are located at the equipment pad. The Load Center enclosure is where the high voltage lines from
the circuit breaker panel junction box at the home are connected to. The pool service person can
periodically check pool operations from the Load Center. Also at the equipment pad there are
system pool and spa pipes connected to the pump, heater and ltration system. Mounted on top the
valves are motorized valve actuators (with attached 25 ft cable for wiring) used to automatically
change the direction ow of water through the plumbing system. There are also temperature sensors
and a cable that connects to the heater.

IntelliTouch®Control System User’s Guide
2
IntelliTouch System Components
The main required components of an IntelliTouch system is a Load Center or Power Center, IntelliTouch
Personality Kit, and Interface:
Indoor Control Panel
• IndoorControlPanel(P/N520138)– 3.75’’ monochrome backlit LCD control panel. Connects to
the IntelliTouch Personality board in the Load Center.
• MobileTouch®Kit(P/N520906)– 3.75’’ monochrome backlit LCD wireless control panel with
Transceiver antenna. Allows any IntelliTouch wired system to also have a wireless remote with all the
capabilities of the Indoor Control Panel. With an average range of 300 feet, pool owners have system
control anywhere around the home or yard. Powered by a rechargeable lithium-ion battery. Includes a
cradle for recharging. The MobileTouch control panel
without the Transceiver antenna (P/N 520907) is also available.
• QuickTouch®II(P/N521245)andQT4(P/N520148)WirelessRemote:Four-function wireless
remote for pool and spa functions of your choice. This controller transmitter operates up to 150 feet
range from the Load Center or Power Center.
• SpaCommand® (P/N521176):10-function (SpaCommand™) and 4-function (iS4) spa-side remote
controller for pool and spa functions of your choice. The controllers can operate up to 150 feet range
from the Load Center or Power Center.
• iPhone™/iPad® TouchInterface(P/N520500) – Includes Protocol Interface Adapter that connects
to existing Desktop or Laptop PC. This allows control of IntelliTouch pool and spa systems via PC
(requires PC with an Ethernet connection, and Windows®XP operating system).
• iTC35Kit(P/N520502)– Includes in-wall color touch screen with Ethernet (RJ45) connection and
Protocol Interface Adapter and wireless router. The in-wall Touch screen is custom congured for
IntelliTouch systems. Requires an Ethernet cable to router.
• iTC45Kit(P/N520503)– Includes wireless Tablet with color touch screen, Protocol Interface
Adapter, and wireless router. The Tablet is custom congured for IntelliTouch.
systems.
In-Wall Touch Screen Digital Tablet
iPhone™
(for use with ScreenLogic2™)
MobileTouch® Wireless Controller SpaCommand™ QuickTouch®II wireless remote

IntelliTouch®Control System User’s Guide
3
IntelliTouch Control System inYour home
8
1
2
3
4
5
6
7
8
9
10
Personal Computer (PC): Existing home owner’s PC or Laptop. Connects to a wireless router and the
IntelliTouch Protocol adapter for control of IntelliTouch pool/spa systems. Requires a PC/Laptop (Windows XP)
with Ethernet/RJ45 adapter installed.
Personal Digital Assistant (PDA): This wireless PDA with a color touch screen enables you to control
your pool and spa features using the IntelliTouch ScreenLogic interface.The PDA is custom configured for
IntelliTouch systems.
In-wallTouch Screen: A color display with Ethernet (RJ45) connector. Connects to the provided wireless router
and Protocol adapter via Ethernet (RJ45) for control of IntelliTouch pool and spa systems.The in-wallTouch
Screen is custom configured for IntelliTouch systems.
WirelessTablet: This control panel consists of a color touch screen.Receives and transmits commands
via wireless router and Protocol adapter for control of IntelliTouch pool/spa systems.The Tablet is custom
configured for IntelliTouch systems.
Indoor Control Panel: This control panel consists of a 3.75’’ monochrome backlit LCD and connects to the
Personality Board in the Load Center or Power Center for control of IntelliTouch pool and spa systems.
MobileTouch: This wireless control panel has a 3.75’’ monochrome backlit LCD. Receives and transmits
commands via the Transceiver antenna located at the Load or Power Center.
Wireless router:Connects to the PC or Laptop via Ethernet connection to the Protocol adapter.
Protocol adapter:Connects to wireless router via Ethernet connection and to Personality board (Load/Power
Center) via a four-wire 22-AWG cable.
Load Center or Power Center.The main control center. Includes the Outdoor Control Panel that controls
pump, heater, and light relays.Receives commands via Protocol adapter, and wireless and wired control panels
connected to the Personality board.
MobileTouchTransceiver antenna: Connects to the Personality circuit board. Sends and receives commands
to and from the MobileTouch wireless control panel.
1
2
3
4
5
6
7
8
9
10
Requied Tools
• 3/16 in. diameter drill (for mounting Indoor Control Panel).
• 3/8 in. diameter drill (for mounting Water Temperature Sensor).

IntelliTouch®Control System User’s Guide
4
IntelliTouch System Components
The main required components of an IntelliTouch system is a Load Center or Power Center,
IntelliTouch Personality Kit, and Interface:
IntelliTouch System Components
The main required components of an IntelliTouch system is a Load Center or Power Center,
IntelliTouch Personality Kit, and Interface:
Load or Power Center
• LoadCenter: Provides a larger footprint (26” H x 17” W x 5-1/4” D) Includes built-in sub panel
(150 AMPS) capable of holding up to eight 1” breakers. Also includes ve 25 AMP three HP
relays, 110/240 V transformer with secondary side circuit protection. Multiple knockouts for
different sizes of conduit are supplied as well as a GFCI side knockout. The Load Center provides
ample space for all high and low voltage wiring needs.
• PowerCenter: Offers a smaller footprint (20” H x 17” W x 5-1/4” D) than the Load Center. The
Power Center does not include a circuit breaker base. Users should choose this enclosure if they
already have existing circuit breakers/sub-panel for their equipment.
IntelliTouch Personality Kits
There are several types of IntelliTouch control systems available for different pool/spa
configurations:
• SharedEquipment:Poolandspacombinationswithsharedltrationsystem–Pool owners
can enjoy the convenience of motorized valves for water ow separation between pool and spa.
The Personality Kit models are:
• i5+3(P/N521219) – Four auxiliary circuits plus lter pump operation (create a Feature
circuit for valve actuators without using an existing output auxiliary circuit, and special
light functions for color lighting). Five relays are included in the Load Center.
• i7+3(P/N521220) – Six auxiliary circuits plus lter pump operation and the +3 option
(create a Feature circuit for valve actuators without using an existing output auxiliary
circuit, and special light functions for color lighting). Two relays are included in the kit
and ve in the Load Center.
• i9+3(P/N521221)– Eight auxiliary circuits plus lter pump operation and the +3
option (create a Feature circuit for valve actuators without using an existing output
auxiliary circuit, and special light functions for color lighting). Four relays are included
in the kit and ve in the Load Center.
• DualEquipment:PoolandSpawithDualSetsofEquipment–The IntelliTouch i10+3D
(P/N 521222) is designed to operate two sets of pool equipment. Each set of a equipment (Pool
or Spa) can control one temperature setting. This IntelliTouch Personality Kit can control up to
10 pumps and/or lighting circuits, plus two heater circuits. The Personality Kit includes, eight
auxiliary circuits plus a lter pump.
The +3 option (create a Feature Macro circuit for valve actuators without using an existing output
auxiliary circuit). Five relays are included in the kit and ve in the Load Center. You can create a
Feature circuit for valve actuators without using an existing output auxiliary circuit, and special
light functions for color lighting.

IntelliTouch®Control System User’s Guide
5
IntelliTouch Personality Kit Contents
The following items are included in the IntelliTouch Personality Kit.
• An IntelliTouch interface
• Outdoor Control Panel. Includes a main controller circuit board and a Personality circuit board.
• Power Relays - (Models i5+3, i5S+3 no relays, i7+3 Qty. 2, i9+3, i9+3S Qty 4, i10+3D Qty 5,
i5x (no relays, i10x (5 relays)
• Valve Actuators - Qty 2 (Models i5+3, i7+3, i9+3)
• Temperature Sensors - Water Sensor (with long cable, including o-ring and hose clamp),
Air Sensors (with short cable). For i10+3D only, two Water Sensor (with long cable)
• Wiring Diagram Label for models i5S+3 and i9+3S and i10+3D. For models i5+3, i7+3, i9+3,
refer to the Load Center and Power Center inside front door.
• Load Center or Power Center parts bag: Includes relay screws (see page 2).
• Label Sheet - A set of adhesive labels for custom identication (used to label the outdoor
control panel buttons). Use a pair of ne-tip tweezers to remove the labels from the sheet.
• IntelliTouch Personality Kit Installation Guide (P/N 521074).
Note: For information about the IntelliTouch Indoor Control Panel and MobileTouch®Wireless
Controller, refer to the IntelliTouch System User’s Guide (P/N 521075).
Select
Menu
Alarm
IntelliChem®Water Chemistry Controller (P/N 521356)
Optional Equipment (IntelliChem)
• IntelliChem® no-pump (P/N 521357), one-pump (P/N 521356), two-pump (P/N 521355)
• IntelliChem Installation and User’s Guide (P/N 521363)
• ExpansionKits: Models i5X (P/N 521225) and i10X (P/N 521226), offer ve or ten additional
Auxiliary Circuits for systems i9+3, i9+3S and i10+3D. Each IntelliTouch Expansion Kit requires
a Load Center (P/N 521213) or Power Center (P/N 521214). Up to three Expansion Kits and
Load or Power Centers may be added to a system, for control of up to 38 Auxiliary Circuits (40
auxiliary circuits for i10+3D).
• SingleEquipment:PoolOnlyorSpaOnlyApplications–The IntelliTouch i5S+3 (P/N 521219)
and i9+3S provide advanced automation for a single body of water. The i5+3S (P/N 521223) and
i9+3S (P/N 521224) Personality Kits includes four auxiliary circuits plus lter pump operation.
Five relays are included in the Load Center. The i9+3S Personality Kits includes eight auxiliary
circuits plus lter pump operation and the +3 option (create a Feature Macro circuit for valve
actuators without using an existing output aux circuit). Four relays are included in the kit and ve
in the Load Center. You can create a Feature circuit for valve actuators without using an existing
output auxiliary circuit, and special light functions for color lighting. This model also allows HI-
TEMP and LO-TEMP settings.

IntelliTouch®Control System User’s Guide
6
IntelliTouch Accessories
521225 i5X Expansion Kit five Auxiliaries.
520906 MobileTouch Wireless Control Panel and Transceiver.
520355 Colored Faceplate Kit for surface-mount.Tan, Grey, or Black with label set.
520354 Colored Faceplate Kit for recessed-mount.Tan, Grey, or Black with label set.
520335 Mud box recessing SpaCommand into deck or tile.
520138 Indoor Control Panel, White.
520198 Two-Speed Three HP Relay up to three additional valve actuators.
520285 Valve module for controlling three additional actuators.
520106 Three HP Power Relay.
687000 Two Telephone remote control for any single circuit, usually Spa mode.
520148 QuickTouch II Four-Function Wireless Remote Kit, Transmitter and Receiver.
520406 Dimmer Module. Supports up to 4,000 Watts maximum load (four dimmers handling
1,000 Watts each).
520442 i-Link Home Automation Adapter Interface for IntelliTouch.
520403 Dual Heater Kit. Utilize a gas heater and heat pump.
ScreenLogic2 Interface Kits
The following items are included in your ScreenLogic2 Kit.
iPhone/iPadTouch Interface Kit (P/N 520500)
• Protocol adapter for use with existing Desktop or Laptop PC, iPhone, iPod Touch, or iPad
• ScreenLogic2 User’s Guide
• CD-ROM containing ScreenLogic2 PC user interface software
In-WallTouch Screen (iTC35 Kit - P/N 520502)
• In-wall Touch Screen, Cradle, and AC adapter.
• Protocol adapter.
• ScreenLogic2 User’s Guide (this manual).
• CD-ROM containing ScreenLogic2 PC user interface software.
DigitalWirelessTablet (iTC45 Kit - P/N 520503)
• Digital Tablet (with internal battery pack), stylus, built-in Wi-Fi 802.11b wireless LAN adapter with
antenna.
• Protocol adapter.
• ScreenLogic2 User’s Guide (this manual).
• CD-ROM containing ScreenLogic2 PC user interface software.
ScreenLogic2 Interface Accessory Kits
If you need additional interfaces, rst order one of the ScreenLogic2 interface kits listed above, then
order one or more of the following accessory interfaces accessory kits:
• In-Wall Touch Screen, CD-ROM and manual (P/N 520498)
• Tablet, CD-ROM and manual (P/N 520499)
Note:The above Accessory Kits interfaces utilize the existing protocol adapter supplied in the
520500 - 520503 kits.

IntelliTouch®Control System User’s Guide
7
Section 2
Operating the IntelliTouch System
Main Screen
(Indoor Control Panel and MobileTouch Wireless Control Panel)
Note: For information about the KEYPAD LOCK feature, see page 80
14
53
34
33
79
33
53
54
56-71
74
75
76
7
38
34
39
81
35
79
35-36
78
81
84
12
81
44 44
12
42
46
83
76
INTELLITOUCH INDOOR CONTROL PANEL BUTTONS
Pg.
Also see page 42
HEATPUMPCOM- Pg.72
SPA OPTIONS -Pg. 77
MAGIC STREAM
THUMPER - TOGGLE
RESET - HOLD / STOP
46
KEYPAD LOCK
Pg. 83
DEGREES C/F - Pg. 77
INTELLICHEM - Pg. 73

IntelliTouch®Control System User’s Guide
8
IntelliTouch Menus
The Indoor Control Panel menus provide system settings to automatically control the general day-to-
day pool and spa operations. From the PROGRAM menus you can program equipment to switch on
and off at specic times. From the SETUP and ADVANCED menus circuit functions, valves and other
equipment can be setup.
7
8
MENU
BACK
DELAY CANCEL
SPA SIDE REMOTE ENABLE
PROGRAM
SETUP
MENU/PROGRAM/SELECT
DISPLAY EXIT
BACK
MENU/SETUP
BACK EXIT
EQUIPMENT
CLOCK
PREFERENCE
ADVANCED
CIRCUIT MACROS
Press MENU button
PROGRAM menus
SETUP menus
POOL (other pool circuits may be
displayed under on the right-side
under the POOL button)
(see page 13)
Setup equipment (page 53)
Set the system clock (page 34)
Setup control panel features,
backlight, beep etc. (page 33)
Setup circuit names, functions,
congure valves (pages 34-41)
1
2
3
OR
SPA (other spa circuits may
be displayed under on the
left-side under the SPA
button)
Press PROGRAM or SETUP button
2
3
Setup MACRO circuit functions
(page 79)

IntelliTouch®Control System User’s Guide
9
Indoor Control Panel Menus
14
53
34
33
79
33
53
54
56-71
74
75
76
7
38
34
39
81
35
79
35-36
78
81
84
12
81
44 44
12
42
46
83
76
INTELLITOUCH INDOOR CONTROL PANEL BUTTONS
Pg.
Also see page 42
HEATPUMPCOM- Pg.72
SPA OPTIONS -Pg. 77
MAGIC STREAM
THUMPER - TOGGLE
RESET - HOLD / STOP
46
KEYPAD LOCK
Pg. 83
DEGREES C/F - Pg. 77
INTELLICHEM - Pg. 73
Setup control panel features,
backlight, beep etc. (page 33)

IntelliTouch®Control System User’s Guide
10
Heating your Spa and Pool
From the Heat screen, use Spabutton (left side) or Poolbutton (right side) to adjust the heat temperature
for your spa or pool. You can also switch the heater on or off from this screen. For single-body systems
(models i5S+3 and i9+3S), spa and pool are replaced with HI-TEMP and LO-TEMP settings (for
more information see page 7).
Adjust Spa or Pool Heat Settings
To adjust the spa or pool set point temperature, go to the Heat screen:
Note:Be sure the SpaMode does not display “OFF.” If “OFF” is displayed, refer to “Configuring
the Heating System Options,” page 11, for more information.
To adjust the spa or pool set point temperature, press the HEAT button at the bottom of the screen:
• SPA:Press the spa Upor Downbuttons (top left and right side) to raise or lower the spa water
temperature. The set point water temperature is displayed in the middle of the screen. The spa
temperature setting can be adjusted from 40° F to 104° F or (4° C to 40° C).
• POOL:Press the pool Upor Downbuttons (third down from the top, left and right side) to raise or
lower the pool temperature. The set point water temperature is displayed in the middle of the screen.
The pool temperature setting can be adjusted from 40° F to 104° F or (4° C to 40° C).
1. Press the Setbutton to save the set point temperature settings. The current spa and pool water
temperatures are displayed on the main screen (see page 7).
2. Press the Backbutton to return to the Main screen.
HEAT
GettingThere
SPA
Press to lower SPA temperature
Hi-Temp Mode for i5S and i9+3S Press to increase SPA temperature
Press to lower POOL temperature Press to increase POOL temperature
Hi-Temp Mode for i5S and i9+3S
Back button Set button