Pentair FLECK 5800 XTR2 User manual

SENSOR PROBE INSTALLATION (FIG. A AND FIG. B)
1. Do not install sensor probes in tank sensor ports before loading tank with gravel and/or resin.
Sensor probes could be damaged by falling gravel and/or resin during loading. (Reference
“5800 XTR2 Enhanced with AccuSense™ Technology Top 3 Tips for Success” for tips on
application suggestions.)
2. Load sensor resin tank with distributor tube, gravel and/or resin per your normal loading
procedure. Dry loading is preferred as some water will exit the tank through the sensor ports
without probes installed.
3. Please note that the sensor probe with the longest wire must be installed in the lower tank
sensor port.
4. Use a clean cloth to remove any debris (resin, etc.) from the tank bulkheads (sensor tank
ports, Fig. A.)
5. Apply 100% silicone lubricant (included) to each O-ring and install in the O-ring groove on the
end of each probe. NOTE:Be careful not to get silicone on the gold-plated sensor probe pins as
this could affect sensor conductivity readings.
6. The probe assemblies are keyed for easy alignment; align probe pins to pin holes in the tank,
and push each probe into the tank bulkhead.
7. Install the red probe retainer clips into bulkhead. Ensure that each clip is fully seated
in the bulkhead.
8. Plug sensor wire harness into appropriate circuit board receptacle, Fig. B.
9. Connect white end of sensor wire harness to white end of the sensor probe assembly.
10. Install probe cover included with tank.
FLECK
5800 XTR2
ENHANCED WITH ACCUSENSE™ TECHNOLOGY
Installation Guide
1
2
3
ONE OF THE FOLLOWING FLECK 5800 XTR2 VALVES:
PN 580008-009 Set up for 8” tanks
PN 580008-010 Set up for 9” or 10” tanks
PN 580008-011 Set up for 12” tanks
This installation guide augments the 5800 XTR2 Service Manual (PN 43359-02).
The Fleck XTR2 Electronic Control now features AccuSense sensor technology capability as of software version 4.0.
For a complete installation, the following components are required:
1
ONE OF THE FOLLOWING STRUCTURAL POLYGLASS TANKS:
PN CH34204-03010201-30 0844 PG 2.5"T UI BLK 9100 SNSRTK COMP BASE
PN CH34205-03010201-30 0948 PG 2.5"T UI BLK 9100 SNSRTK COMP BASE
PN CH34206-03010201-30 1054 PG 2.5"T UI BLK 9100 SNSRTK COMP BASE
PN CH34299-03010201-30 1248 PG 2.5"T UI BLK 9100 SNSRTK COMP BASE
2
ONE PENTAIR ACCUSENSE SENSOR PROBE ASSEMBLY
PN 61893 KIT, SENSOR PROBE ASSEMBLY
3

4007090 REV B SE23
13845 Bishops Dr. | Suite 200 | Brookeld, WI 53005 | United States
P: 262.238.4400 | Customer Service: 800.279.9404 | [e-mail] | pentair.com
All indicated Pentair trademarks and logos are property of Pentair. Third party registered and unregistered trademarks and logos are the property of their respective owners.
© 2023 Pentair. All rights reserved.
13845 Bishops Dr. | Suite 200
Brookeld, WI 53005 | United States
P: 262.238.4400 | Customer Service: 800.279.9404
[e-mail] | pentair.com
All indicated Pentair trademarks and logos are property of Pentair. Third party registered and
unregistered trademarks and logos are the property of their respective owners.
© 2023 Pentair. All rights reserved.
To Choose Sensor Regeneration Type
From the XTR2 main Master Settings screen, press the valve button to display the
valve screen.
Press the regen. type button and scroll through the options until the tank sensors
option is seen. Press the check mark button to select.
NOTE: Hardness and hardness units settings will no longer be available when in the
regen. type; tank sensors mode.
Follow the setup instructions outlined in the Fleck 5800 XTR2 Service Manual
as you power up the system.
BEGIN VALVE SETUP
Should you have questions about setup, contact Pentair Tech Support
at [e-mail].