Pet Gear PG8600BOB User manual

To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™
INSTRUCTION MANUAL
ROADSTER PET STROLLER
PG8600BOB/PG8600BPK
AT
Interior Dimensions:
33L x 20W x 21H

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK
2
PARTS LIST
BACK WHEEL ASSEMBLY INSTRUCTIONS
Step 1. Slide back wheel on axle as shown
in Figure A.
Step 2. Push in axel until it clicks.
Step 3. Pull on wheel to make sure the
wheel is engaged.
Repeat on other side.
When nished it should look like Figure B.
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service.
Stroller
Axle
Front Wheel
A.
B.
2-Back Wheels

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK 3
BACK WHEEL ASSEMBLY INSTRUCTIONS
To remove wheel, push the lock/release button
(Figure C) and pull wheel off.
Step 4. Take rear wheels (on axel with
brakes) and lock them into the 2" posts
by placing leg tube over the posts and
pressing down until they click (shown in
Figure D).
Pull up to make sure wheels are locked.
Step 5. Place stroller so wheels are on
the ground and back wheels are facing
you (shown in Figure E).
Inside Outside
Lock/Release Button
Back Wheels
D.
C.
E.
To remove
axel press on
velco button.

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK
4
Step 6. Lift right and left side of stroller up (shown
in Figure F).
Secure the support bar that goes from the left and
latches down on the right side (shown in Figure F).
Step 7. To install the handle, place handle
ends into the handle-locking mechanisms on
each side of the stroller.
Then, push down until you hear a click and
the velco pins pop out on each side.
Choose height level (1 or 2), then release
velco pins.
Pull up on handle to make sure it is securely
locked.
This is shown in Figure G.
BACK WHEEL ASSEMBLY INSTRUCTIONS
F.
Velco Pin
Handle Locking Mechanism
G.

EXPEDITION PET STROLLER • PG8800BG/PG8800BS 5
FRONT WHEEL ASSEMBLY INSTRUCTIONS
Step 1. To attach front wheel, slide plastic wheel support
up and into tubing.
Step 3. To use stroller in locked position for jogging,
push pin in.
Step 2. Slide wheel up, until velco pins pop out
of holes.
Step 4. To use stroller in swivel position, pull
pin down, and to the right.
Tubing Tubing
Swivel
Position
Velco Pin Velco Pin
Locked Position

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK
6
Step 2. Pull support bar up to release and continue to
swing the bar counter-clockwise.
TO FOLD/PACK UP STROLLER
Step 1. Remove handlebar, by pushing velco pins in to
release.
Pull handlebar up and off.
Velco
Pin
Step 3. Fold sides inward, until at.

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK
LOOKING AFTER YOUR STROLLER
WHEEL MAINTENANCE
• Always store product in a clean, dry place.
• Not recommended for use on the beach.
• Do not put heavy items on top of the stroller.
• Clean frame by wiping with a lightly oiled cloth.
• Do not use detergent or abrasives. Spot clean fabric with dry cleaning uid or mild soap and
warm water.
• To ensure easy maneuverability and to minimize wear and tear, (especially wheels, axles, and
swivels), keep all moving parts clean and lubricated with WD40® or light machine oil.
• NOTE: Do not lubricate brake components or swivel locks.
• Regularly check stroller for loose parts. These should be tightened or replaced.
• To clean and lubricate front and rear wheels, push out locking lever under wheel housing to
release rear wheel.
• To ensure ease of maneuverability and to minimize wear and tear, keep all moving parts clean and
lubricated with WD40® or light machine oil.
• Push wheel sets back on until they click and lock in position; pull on wheel housings to ensure
they are secure.
• Push stroller back and forth and rotate swivels around to work in lubricant.
• Clean the rear wheel assembly and the rest of the frame with warm, soapy water; clean off with
warm water and dry thoroughly.
• NOTE: Do not lubricate brake components or swivel locks.
7

ROADSTER PET STROLLER • PG8600BOB/PG8600BPK
8
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig, chew or paw
aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage caused by aggressive,
destructive, immature or untrained animals. Do not use near an open or exposed ame. Failure to follow these
warnings and the instructions could result in serious injury or death.
• Do not carry additional bags, goods, or accessories in or on stroller except as recommended
in the manufacturer’s instructions.
• Recommended use of an approved safety restraint correctly tted and adjusted.
• Do not leave pet unsupervised in stroller.
• Before making adjustments to stroller ensure that pet’s body is clear of any moving parts.
• This stroller is designed for one pet only.
• Do not hang bags from handles as this may cause the product to become unstable.
• Do not use on escalator or stairs; fold stroller and carry.
• Put on brake whenever you park the stroller.
• Ensure stroller is completely erected and check that all locks are engaged before placing pet
in stroller.
• Do not overload as stroller may become unstable; maximum weight of pet using this stroller
not to exceed 100 lbs.
• Any goods carried in the basket not to exceed 6 lbs.
REPLACEMENT PARTS
Use only PET GEAR replacement parts.
Please have your model number ready before calling.
You can also request parts: http://www.petgearinc.com/main.asp?sel=2
PO Box 99∙West Rutland, VT∙05777∙877-752-9123∙www.petgearinc.com