Pet Gear PG9816DBG User manual

INSTRUCTION MANUAL
DESIGNER 2-STEP
PG9816DBG/PG9816DCH/PG9816DSG/PG9816DTN
PG10116DBG/PG10116DCH/PG10116DSG/PG10116DTN
To see our full line of products, visit us online at: www.petgearinc.com
CUSTOMER SERVICE HELP DESK
[email protected]
Toll-Free 877-752-9123 - Eastern Standard Time 8am-3pm, Monday through Friday
For The ON-THE-GO Pet™
Carpet treads and designer
cover remove easily and
are machine washable.
For Pets
Only

PARTS LIST
Check that you have all the parts shown BEFORE assembling your product.
If any parts are missing, call Customer Service. No tools required.
2
Step 1
Place right panel, part (B) on floor with
PET GEAR Logo facing the floor and
insert top stair, part (E).
Keep the STRAIGHT EDGE
toward the back and rug facing the top.
Make sure there are no gaps between parts
after inserting.
(If inserting part is difficult put a little dish
soap on doweled end before inserting.)
Step 2
Insert riser, part (C). Make sure there are no
gaps between parts after inserting.
DESIGNER 4-STEP PG9840DBG/PG9840DCH/PG9840DSG/PG9840DTN
PG10140DBG/PG10140DCH/PG10140DSG/PG10140DTN
B
C
E
B
A
Left Panel Right Panel (1)
(1)
Make sure rubber
grippers are on the
bottom.
(1)
(1)
(3)
(1)
F
C
E
D
Riser Dowel
Carpet Treads
Stairs
Top Stair
(2)
Designer Cover
H
(1)
STRAIGHT
EDGE
INSTRUCTIONS
G

INSTRUCTIONS
3
Step 3
Insert stair, part (F). Note the CURVED SIDE
direction. Make sure there are no gaps between
parts after inserting.
Step 5
Insert dowel, part (D). Make sure there are no gaps
between parts after inserting.
Step 4
Insert riser, part (C). Make sure there are no gaps
between parts after inserting.
Step 6
Attach left panel, part (A). Align all holes
before pushing panel down. Make sure there
are no gaps between parts after inserting.
DESIGNER 2-STEP PG9816DBG/PG9816DCH/PG9816DSG/PG9816DTN
PG10116DBG/PG10116DCH/PG10116DSG/PG10116DTN
F
C
D

4DESIGNER 2-STEP PG9816DBG/PG9816DCH/PG9816DSG/PG9816DTN
PG10116DBG/PG10116DCH/PG10116DSG/PG10116DTN
INSTRUCTIONS
Step 7
Unfold the Designer Cover, (H),
and drape it over the steps. Pull
the elastic strap over the bottom
of the stairs.
Step 9
Place carpet treads, (G), on top of the steps and
connect with Velcro strips.
Step 8
Pull the zipper down toward the floor.
Velcro Strips
G
(Bottom view.)
Elastic strap.
H
H

5
WARNING!
FOR PETS ONLY.
Not intended to be used as a restraining device for aggressive or dangerous animals that dig,
chew or paw aggressively. Do not leave your pet unattended. PET GEAR is not liable for any damage
caused by aggressive, destructive, immature or untrained animals.
Do not use near an open or exposed
flame. Failure to follow these warnings and the instructions could result in serious injury or death.
REPLACEMENT PARTS
Please have your model number ready before calling. Use only Pet Gear replacement parts.
DESIGNER 2-STEP PG9816DBG/PG9816DCH/PG9816DSG/PG9816DTN
PG10116DBG/PG10116DCH/PG10116DSG/PG10116DTN
PO Box 99
West Rutland, VT 05777
877-752-9123
www.petgearinc.com