Phanteks GLACIER G40 MSI User manual

INSTALLATION GUIDE V1.0
GLAC IER G40 MSI GPU BLOCK
PH-GB4090MS_BK01/CR01/MW01_BP
PACKAGE CONTENTS
WARNING - This product is intended for advanced users. Improper installation may result in damage to your equipment.While all eorts have
been made to provide the most comprehensive information possible, Phanteks assumes no liability expressed or implied for any damage(s) occurring to your
components as a result of using Phanteks cooling products, either due to mistake or omission on our part in the below instructions, or due to failure or defect in
the Phanteks cooling products. Do not disassemble the water block.Warranty will be voided.
STEP 1. REMOVING STOCK COOLER
MSI RTX 4090 GAMING(X) TRIO
MSI RTX 4090/4080 SUPRIM (X)
Unscrew all highlighted screws to remove
the stock cooler and backplate.
Some SUPRIM models require
you to remove these 2 screws.
Secure again with 2x M3 Nuts and
original screws.
Make sure to unplug the LED and Fan
cables when you remove the stock cooler.
backplate screws
MSI SUPRIM PCB version: V510-2.2
stock cooler screws
Clean o the original thermal compound.
We recommend using isopropanol alcohol.
Remove the protective lm and place the
the thermal pads on the correct position
on the PCB.
Apply the Phanteks Thermal Compound to
the center of the GPU chip.
STEP 2. APPLYING THERMAL PASTE & PADS
Make sure to remove the protective lm on
both sides of the thermal pads.
MSI RTX 4090/4080 SUPRIM (X) / GAMING(X) TRIO
Keep for step 3
GB4090MS block
QTY: 1
GB4090MS backplate
QTY: 1
GLACIER stop tting
QTY: 2
Support bracket
QTY: 1
Block thermal pads
QTY: 2 pre-cut pieces
M2.5x5 screws/washers
QTY: 4/4
M3x10 screw (1x)
M3 Nut (2x)
Backplate thermal pads
QTY: 2 pre-cut pieces
M2.5x8 ush screws
QTY: 11
Thermal compound
QTY: 1
Phanteks D-RGB cable
QTY: 1
Motherboard cable
QTY: 1
1
2
3
45
10
12 11 11 11 11 11
8
6 6 6 6
7
3
10 12
12
6
66
6
4
3 3
7
5
8
11
11 11
1111
2x

STEP 5. INSTALL THE BACKPLATE
Carefully position the backplate onto the
graphics card. Align the mounting holes on
the PCB with the holes on the backplate.
Secure the backplate with 11 M2.5x8mm
ush screws to the PCB.
1.
11x
STEP 4. APPLYING THERMAL PADS
Remove the protective lm on both sides
and place the thermal pads on the correct
position on the backplate.
STEP 3. MOUNT THE WATER BLOCK
Secure the support bracket to the GPU block
rst.
Carefully position the water block onto the
graphics card. Align the mounting holes on
the PCB with the holes on the water block.
Secure the water block with 4 M2.5x5mm
screws and washers to the PCB.
Secure the Support Bracket with the original
cooler screw.
4x
4x
Make sure to lay the GPU with the water
block at down without resting on the
PCI bracket. Secure with original
screw.
Always perform a leak test before
providing power to any system components.
STEP 6. INSTALL INTO THE SYSTEM
1. Connect the D-RGB cable to the D-RGB
strip in the water block.
2. Install the GPU into the system.
3. Install the waterloop and Stop Fittings
Use the Motherboard cable to connect
the LED strip to the motherboard.
Opotional:
All Phanteks D-RGB products can be
daisy-chained together.
Connect to
Phanteks Case / Motherboard Cable
2
4
2 3
1
5
1x
5
2 2
3
4
1