Philips dynalite DUS704W User manual

Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia
t [phone] f [phone] [email protected]m ABN 33 097 246 921 Philips.com/dynalite
DUS704W
Wall Mount Universal Sensor Installation Manual
The DUS704 series combine motion detection (PIR), infra red remote control reception (IR) and
ambient light level detection (PE) in the one device. In applications such as homes, lecture
theatres and office towers, DUS704W universal sensors can be utilised to detect motion and
switch on the lights.
When rooms are unoccupied, lights can be automatically dimmed or switched off to provide
energy savings. The same sensor provides IR remote control reception to give full control over
lights, audio-visual equipment and blinds. A range of hand held infra-red transmitters to
complement DUS704W series universal sensors.
In situations where it is critical to maintain precise lighting control for individual workspaces, such
as a flight control tower or office workstation, the DUS704 facilitates light compensation. The
DUS704W can be placed in an automatic “Daylight Harvesting” mode for energy savings.

installation steps
2DUS704W Installation Manual Rev I
1. * WARNING * Do not touch the Pyro Sensor with your fingers. For indoor use only and not to be
used as a sensor for integration to a security system.
2. Select an appropriate indoor mounting location, as detailed in the location guidelines on the following
pages. Note that this product has three functions, and the optimum mounting location for each
individual function may conflict with each other, and may require the use of multiple sensors.
3. Remove the cover from the base unit by un-clipping the bottom of the cover and hinging it upwards.
4. Screw the base unit to the wall, ensuring the unit is mounted vertically. Pass the data cable through
the cable entry hole.
5. Ensure that the lens is properly mounted
6. Terminate the data cable as shown below.
7. Use silicon sealant to seal any cable entry and screw holes to prevent air draughts, dust and insects
from entering the enclosure.
8. Replace the cover onto the base unit by locating it in the top clip position then hinging it downwards.
Remove the screw cap at the bottom of the housing, insert and loosely tighten the supplied
screw, then replace the screw cap. Ensure that the housing is proper enclosed and sealed
internal view

connecting data cable
DUS704W Installation Manual Rev I 3
motion detection mounting location
• Fix the sensor to a firm section of wall
• Position the sensor so it is between 1.1 and 3.1 metres from the floor. Optimum height for the sensor is 2.1
metres.
• Slide the circuit board up or down so the marker on the housing matches up with the installed height on the
scale provided on the right hand side of the circuit board.
• Position the sensor so it is at least 2 metres away from electrical lighting such as neon and fluorescent
lights.
• Position the sensor as to avoid exposing it to direct sunlight and heating / cooling sources.
• Keep data cables away from electrical wiring.
• Select a location where persons are more likely to walk across the detection “fingers” rather than into them
(see diagram below).
• For programming instructions refer to Dynalite Tech Note –Setting up Motion Detection functions.
motion detection lens pattern
INSTALLATION DETA ILS
DIMTE K 110
INPUT: 230 V 5 0-6 0Hz 10 A
OUTPUT: 1 x230V 10A
MOUNT VER TICAL LY
AGAINST WALL
ENSURE G OOD VENTI LATION
FOLLOW INST ALLAT ION
INSTRUCTIONS
Unit6-11 9 /133 M cE VOY S t. A lexandria
NSW 2015A USTRA LIA
Manufactured by:
ISOLATEF ROM
MAINSS UPPLY BEFO RE
REMOVING THISC OV ER
NOUS ER SERV ICEABLEPA RT S INSIDE
SERVICE BYQ UALIFIE D PERSONNEL ONLY
INSTALLATION DETA ILS
DIMTE K 110
INPUT: 230 V 5 0-6 0Hz 10 A
OUTPUT: 1 x230V 10A
MOUNT VER TICAL LY
AGAINST WALL
ENSURE G OOD VENTI LATION
FOLLOW INST ALLAT ION
INSTRUCTIONS
Unit6-11 9 /133 M cE VOY S t. A lexandria
NSW 2015A USTRA LIA
Manufactured by:
ISOLATEF ROM
MAINSS UPPLY BEFO RE
REMOVING THISC OV ER
NOUS ER SERV ICEABLEPA RT S INSIDE
SERVICE BYQ UALIFIE D PERSONNEL ONLY
Connect Data Cable in a "Daisy Chain"
serial cable permanent connectors
connect data cable in a “daisy chain”
Recommended Cable Colours
Green/White Pair paralleled for GND
Orange/White Pair paralleled for +VE
Blue/White Pair Blue for DATA
White for DATA-
Recommended Cable Types
Belden: 9503
Garland: MCP3S
Hartland: HCK603
M&M Cable: B2003CS
Dynalite: DYNET-STP-CABLE
Side view
Top view

optional motion detector lens
4DUS704W Installation Manual Rev I
In addition to the supplied Wide Angle lens, An option for a long range lens is available for corridor
applications:
• DUS704W Long Range – Useful for monitoring a long thin space such as a corridor.
Contact your local supplier for more details
infrared receiver mounting location
• Position the sensor so it is within 6 meters of the intended operating positions of the infrared transmitter
• Position the sensor so it is not directly exposed to light, especially incandescent and sunlight, both of which
can substantially reduce IR range
• Keep data cables away from electrical wiring
photo electric cell mounting location
• Position the sensor so it “sees” a combination of artificial light and natural
light
• Position the sensor so it is not directly exposed to artificial light or sunlight
• Keep data cables away from electrical wiring
• For programming instructions refer to Dynalite Tech Note - Setting up PE
functions
6.0 Meters Max
Optional Lens –DUS704W Long Range

specifications
DUS704W Installation Manual Rev I 5
DUS704W Instruction Manual Rev I.doc. Specifications and design subject to change without notice.
Philips Dynalite manufactured by WMGD Pty Ltd (ABN 33 097 246 921). Unit 6, 691 Gardeners Road Mascot NSW 2020 Australia Tel: [phone] Fax: [phone]
E-Mail: dynalite.inf[email protected] Web: Philips.com/dynalite
Motion Detector
Wide Angle Wall Mount PIR Detector
Range 12m x 90O (standard lens)
Mounting height: 1.1m to 3.1m
LED activation indicator
Adjustable Pulse Count & Sensitivity
Detection zones: 20 dual element zones
Sensor: Dual element pyro-electric
R.F.I. Immunity: >15V/m @ 10- 1000MHz
Optional lens:
* 30m x 30O Long Range
PE Cell
Dynamic range < 5 lux to > 5000 lux
Automatic “Daylight Harvesting” mode
Can be used for light measurement
Installation Position
Wall mount, indoor use only
Infra Red Remote Control Receiver
Range > 6m
LED activation indicator
Can be used with DTK500 series
Infra Red remotes or other learning
IR Remote controls
Dimensions
H 85mm x W 66mm x D 45mm
Control IO
Serial Port –RS485 DyNet
DyNet DC Load
20mA
Setup
All functions remotely
programmable
Weight
0.1Kg Packed