Philips OccuSwitch LRM1070/00 User manual

OccuSwitch
LRM1070/00 Sensr Mov Det St
The OccuSwitch to czujnik ruchu z wbudowanym przełącznikiem.
Potrafi wyłączać światło w pomieszczeniu lubna otwartej przestrzeni
po opuszczeniu jej przez ostatnią osobę, obniżając w ten sposób
zużycie prądu nawet o 30%Przełącznik OccuSwitch może włączać
instalacje pracujące na prądzie do 6 A oraz kontrolować
pomieszczenia o powierzchni od 20 do 25 m<SUP>2</SUP>Złączka
sieci zasilającej zapewnia łatwy montaż przełącznika OccuSwitch na
suficieDostępny jest osobny przewód Wieland umożliwiający łatwy,
szybki i bezproblemowy montaż
The OccuSwitch to czujnik ruchu z wbudowanym przełącznikiem. Potrafi wyłączać światło
w pomieszczeniu lubna otwartej przestrzeni po opuszczeniu jej przez ostatnią osobę,
obniżając w ten sposób zużycie prądu nawet o 30%Przełącznik OccuSwitch może włączać
instalacje pracujące na prądzie do 6 A oraz kontrolować pomieszczenia o powierzchni od
20 do 25 m2Złączka sieci zasilającej zapewnia łatwy montaż przełącznika OccuSwitch na
suficieDostępny jest osobny przewód Wieland umożliwiający łatwy, szybki i
bezproblemowy montaż
Danych wyrobów
Dane techniczne produktu
Pełny kod produktu 871155973138499
Nazwa produktu na zamówieniu LRM1070/00 SENSR MOV DET ST
EAN/UPC - Produkt 8711559731384
Kod zamówienia 73138499
Numerator - Liczba sztuk w opakowaniu paczce 1
Numerator – Liczba paczek w opakowaniu zewnętrznym 42
Materiał Nr (12NC) 913700327803
Waga netto (szt.) 0.200 kg
Datasheet, 2018, Maj 18 Dane wkrótce ulegną zmianie
LightingLighting

Rysunki techniczne
Ø 80
Ø 95
50
LRM1070/00 SENSR MOV DET ST
Product
LRM1070/00 SENSR MOV DET ST
OccuSwitch
© 2018 Philips Lighting Holding B.V. Wszelkie prawa zastrzeżone. Dane mogą ulec zmianie bez uprzedniego powiadomienia.
Znak towarowy jest własnością Philips Lighting Holding B.V. lub odpowiednich podmiotów.
www.lighting.philips.com
2018, Maj 18 - Dane wkrótce ulegną zmianie

Product guide
OccuSwitch movement
detector
LRM1070, LRM1080

2Product Guide - LRM1070, LRM1080
LRM1070, LRM1080
The OccuSwitch is a movement detector with a
build-in switch. It will switch o the lights in a room
or area when it is vacated and thus save up to 30% of
electrical energy. The OccuSwitch can switch any load
up to 6A and control an oce area of around 20m2.
A detachable mains connector enables easy
installation and mounting of the OccuSwitch in the
ceiling.
A separate Wieland cable is available for easy,
fast and trouble-free installation.
The OccuSwitch family exists of:
LRM1070 Basic OccuSwitch
LRM1080 Advanced OccuSwitch
LCC1070 Wieland cable
LRH1070 Ceiling mounting box
Dimensional drawing
LRM1070 Basic OccuSwitch, LRM1080 Advanced OccuSwitch
LCC1070 Wieland cable
LCC1070 Wieland cable
LRH1070 Ceiling mounting box
LRH1070 Ceiling mounting box
Ø 95 mm (3.74 in)
51.5 mm
(2.03 in)
56 .. 66 mm
(2.20 .. 2.60 in)
500 mm (19.69 in)
67.5 mm
(2.66 in)
26.5 mm
(1.04 in)
113.5 mm (4.47 in)
50 mm (1.97 in)
Ø 80 mm (3.15 in)
2 mm (0.08 in)
Ø 95 mm (3.74 in)

Product Guide - LRM1070, LRM1080 3
The OccuSwitch is designed for use in oces and
similar applications, including toilets, storage rooms,
etc. It is optimized for recessed ceiling mounting and
for mounting heights between 2.5 and 3.5 meter.
The surface box allows surface-mounting as well, with
either recessed wiring or surface-mounted ducts.
The advanced OccuSwitch can be connected in
parallel (max 10) to cover larger area’s like open plan
oces. The use of dierent mains groups or even
phases is no problem.
The OccuSwitch’s detection pattern (see drawing) is
4 by 5 meters for minor movements (desk work) and
6 by 8 meters for major movements like walking.
Detection pattern Position OccuSwitch
Standard application Parallel operation
Functions (both versions)
Automatic control
The OccuSwitch switches the lights on automatically
when movement is detected and switches the lights
o after the area is vacated (after 1 to 30 minutes
depending on the settings).
Daylight override
It is possible to prevent the automatic switch-on
when sucient daylight is available in order to create
additional savings.
Daylight switching
When daylight switching is active, the lights will
automatically be switched o when sucient daylight
becomes available, and turned back on when the light
level drops below the required level.
Functions advanced version
Parallel operation
It is possible to connect up to 10 OccuSwitches in
parallel via a separate bus signal. When one of the
OccuSwitches detects movement, all units will switch
the lights on. The bus signal is fully isolated, so each
OccuSwitch can be used on any mains group or
phase, allowing the use of several mains groups in an
area and easy wiring.
Local override
With a remote control it is possible to override the
automatic operation of the OccuSwitch, for instance
to switch lights o even if there is movement detected.
Absence mode
When a remote control is used it is also possible to
disable the automatic switch-on when people enter
the area that the OccuSwitch is controlling.
Features (both versions)
Smart timer
The smart timer will extend the delay time by 10
minutes if movement is detected shortly after switch-
o, assuming that the area is still in use, but very little
movement is made.
Shield
The OccuSwitch has a retractable shield that can be
used to shield o areas like corridors, adjacent to the
area the OccuSwitch is controlling.
Features advanced version
Remote tool
With a remote control tool (IRT9090) it is possible to
change the light level settings without the need to
reach for the OccuSwitch itself.
Using the tool it is possible to change the power-up
setting from its default (switch-on). The OccuSwitch
will not switch on at power-up and will start detection
30 seconds later.
Applications
8m5m
6m
4m
4m
5m
5m
4m
5m
4m

4Product Guide - LRM1070, LRM1080
Mounting
Fixing
The OccuSwitch can be mounted in two ways;
recessed in the ceiling or surface-mounted using
the ceiling box.
The ceiling box (LRH1070) has breakout ports for
cable ducts and a breakout centrepiece.
When selecting a location for the OccuSwitch, avoid
obvious cold spots so that condensation does not
occur.
Fixing the OccuSwitch in a ceiling (recessed)
Fixing the OccuSwitch on a ceiling
(surface-mounted)
80-82 mm
> 50 mm
≤ 30 mm
11
2
max. 185 mm
No. 8 (Ø 4 mm)
35
Ø 95 mm (3.74 in)
51.5 mm
(2.03 in)
56 .. 66 mm
(2.20 .. 2.60 in)
3
1
2
4
5
22 x 10 mm
25 x 13 mm
25 x 16 mm
16 x 16 mm
LRH1070
LRM1070
LRM1080
3
1
2
4
5
22 x 10 mm
25 x 13 mm
25 x 16 mm
16 x 16 mm
LRH1070
LRM1070
LRM1080

Product Guide - LRM1070, LRM1080 5
The OccuSwitch can be installed with either
conventional wiring or Wieland connectors. For
the second option, the Wieland cable (LCC1070) is
required. The OccuSwitch comes with a detachable
mains connector for easy installation. This connector
is removed if the Wieland cable is used. The mains
connection is protected by a retractable cover and
secured with a tie wrap.
Installation (conventional wiring)
Installation (Wieland)
DNote
The connector of the OccuSwitch is capable of
accepting a wide range of cables (1.5 to 2.5mm2),
but when heavy ridged cables (especially single
core) are used it is strongly advised to make use of
the LCC1070 to prevent the OccuSwitch of being
pushed out of the ceiling due to the weight of
these ridged cables.
Parallel operation
Parallel operation is used to enlarge the covering area
of the OccuSwitch. This can be done in two ways;
either by parallel installation or by using the parallel
connection of the advanced OccuSwitch (LRM1080).
Parallel installation limits the total load to 6A and
restricts the application to one mains group. For
parallel connection the LRM1080 uses a bus signal to
indicate movement detection to other units. All units
can be used up to 6A each and with several mains
groups (or even phases). A short delay between the
dierent units during switch-o may occur. Max. 10
LRM1080 in parallel.
Parallel installation
Parallel connection (advanced only)
Electrical Installation
L
N
Ls L N
L
N
Wieland cable (LCC1070)
2click
3
45
1
H05VV-F
Ls L N
L
N
Ls L N
-+
Ls L LN
-+
Ls N
L1
L2
L3
-
+
N

6Product Guide - LRM1070, LRM1080
Commissioning
Daylight control
Daylight override
The daylight override function prevents the lights from
switching on when sucient daylight is available. To
enable this function it is necessary to set the required
light level by turning the dial counterclockwise (CCW)
away from the OFF position. To disable this function,
turn the dial clockwise (CW) into the OFF position.
Daylight switching
This function will actively switch the lights o if
sucient daylight is available.
To enable this function, the DIP switch for this
function has to be set to the ON position and the light
level must be set (see daylight override).
When this function is enabled, lights will switch o
when the light level is above 220% for more than 15
minutes.
When switching o, the available daylight reaches at
least 120% of the required light level. The lights will
switch on again when the light level drops below the
required level.
Enabling daylight override and switching
D Note
This function can only work correctly if the
required light level is the same as the installed
light level. The OccuSwitch will automatically raise
the switch-o level if the required light level is set
well below the installed light level (for instance
500 Lux required with 1000 Lux installed). This
will prevent the lights from switching on and o in
a 15 minute cycle.
The OccuSwitch can switch o once or twice (with
a 15 minute delay) for reference purposes. This
cycle will repeat every time the OccuSwitch is
reconnected to the mains power.
Calibration
Turn the dial to raise or lower the required light level.
Calibration
Local control (LRM1080)
The OccuSwitch LRM1080 (advanced version) will
react to commands given by a suitable Philips remote
control. There is no special setting required. Although
the OccuSwitch will operate with all remotes capable
of sending the right codes, the IRT8050 (wall-
mounted) is best suited for this application.
The OccuSwitch will respond to channel 1 codes (on/
o). By default it will respond to group A and general
codes.
Only with the IRT9090 is it possible to change the
group address to make a distinction between dierent
OccuSwitches and remote controls. The OccuSwitch
does not react to preset commands.
The remote control should be operated within the
detection area of the OccuSwitch.
IRT8050
Absence mode
The OccuSwitch will not switch on the lights
automatically in absence mode. A remote control
must be used to switch on the lights. The OccuSwitch
will switch o after 1 to 30 minutes after the area is
vacated. Set the DIP switch in the right position to
activate the absence mode.
Enabling absence mode
-+= o
ON
1 2 ON
1 2
on
o
-+
ON
1 2
Auto on
IR on
ON
1 2

Product Guide - LRM1070, LRM1080 7
Set required light level
Make certain that the required light level is available
and no daylight is entering the area.
Calibrate by aiming the IRT9090 towards the
OccuSwitch and pressing the “save” button.
The lights will ash once to indicate the new level is
stored.
IRT9090 Calibrate light level
Change IR group
Both the OccuSwitch and remote controls can operate
in 7 dierent groups. Both the remote controls and
OccuSwitch must be in the same group.
Select the “IR group” button on the IRT9090, followed
by the desired IR group (A-G, buttons 1 to 7).
Aim the IRT9090 towards the OccuSwitch and press
the green “send” button. The lights will ash once to
indicate the new setting is stored.
Send command
Change power-up behaviour
The OccuSwitch switches the output on when it is
connected to the mains. If the area is vacated the
lights will switch o after 5 minutes.
It is possible to leave the output o and start
movement detection 30 seconds after the mains is
connected.
On the IRT9090 select the “power up” button,
followed by either “on” or “o”. Aim the IRT9090
towards the OccuSwitch and press the green “send”
button. The lights will ash once to indicate the new
setting is stored.
Restore defaults
To restore the default settings, aim the IRT9090
towards the OccuSwitch and press the “reset” button.
DNote
The IRT9090 will send the power on and IR group
settings together (if changed). To erase previous
settings press “reset” followed by “send” on the
IRT9090.
B Warnings
The OccuSwitch should not be used in the
following situations:
• In applications outside the specication range,
most notable heights above 3,5 meter.
• Environmental conditions other than in a normal
oce environment (temperature, humidity).
• In applications with heat sources like electrical
heaters, within the detection range of the
OccuSwitch.
• In combination with lighting sources, or other
devices, that can be damaged if they are
switched o and on in a short period of time.
B Warnings advanced version
The OccuSwitch should not be used in the
following situations
• In applications with (semi-continuous)
IR appliances like IRDA communication,
IR communication between PDA and phones
and other devices, headsets operating
with IR communication, etc. Please note
that some devices with IR communication
send IR messages, even when there is no
communication link. These features must be
disabled.
• In applications with electronic ballasts that
operate up to or near the IR transmission
frequency of 36Khz. Also when these
ballasts are not used in combination with the
OccuSwitch, but the light from the lamps they
operate is visible to the IR receiver.
IRT9090 (LRM1080)
70% G
min
100 h
group
link? mode?
mode
power up background IR group reset
add
pirdelay daylight RF channel
0
0
o
save
on
I/ II
O)))
A-G
zone
%
on/o
87 9
50% E40% D 60% F
54 6
20% B10% A
II
30% C
PLBMS W/C
21 3
test
cong
scene
Max. 17m
= 1x
Max. 17m
= 1x
Luxmeter
Luxmeter

8Product Guide - LRM1070, LRM1080
Specications
Mains connection
Voltage 230VAC +/10%; 50/60Hz
Maximum load 6 A. (1380 VA) any load
Connector screw
terminal
MRT3P7.62-3VE or
GMVSTBW2.5/3-ST-7.62
Maximum wire range 1.5 to 2.5mm2
Mains distribution
system
TN-S, 16A max, with
Neutral grounded
Power consumption
Stand-by 1.2 W
Max. 1.2 W
Environmental
Temperature +5 to +50°C (operating)
-20 to +70°C (storage and
transport)
Relative humidity 20% to 90% (no
condensation)
Parallel interface
Maximum 10 units in parallel
SELV signal, max 5 V.
Free Topology Wiring
Polarity sensitive
Connector type screw terminal
CPF5.08-2VE or
MSTB2.5/2-ST-5.08
Maximum wire range 1.5 to 2.5mm2
Maximum length 100m
Settings
LED indicator Red on movement
detection
Switch o delay 1 to 30 minutes
Light levels 250 to 1000 Lux
(30% reection)
Detection range see diagram
The remote control and
light sensor work in a
similar range.
Compliances and approvals
Standards EN/IEC 60669-2-1
Electronic switches
Classication Class I
Pollution degree 2
Over voltage category III
Approbation Product complies with
the relevant European
Directive (CE)
KEMA
EMC
Compliance IEC (EN) 60669-2-1
Immunity IEC (EN) 61547
Emission IEC (EN) 55015 and IEC
(EN) 55022, class B
Housing
Protection Class IP20
Flammability UL94 V-0
Glow wire test 960°C/5s.
Insulation Double
insulation
(4kV) between Mains
and SELV
Weight 0.2 Kg

Product Guide - LRM1070, LRM1080 9
Packing data
Ordering Data
Type Box dimensions
(mm)
Qty Material Weight (Kg)
net gros
LRM1070 Unit box 105 x 95 x 58 1 cardboard 0.12 0.15
LRM1070 Outer box 400 x 300 x 300 42 cardboard 5 5.6
LRM1080 Unit box 105 x 95 x 58 1 cardboard 0.12 0.15
LRM1080 Outer box 400 x 300 x 300 42 cardboard 5 5.6
LRH1070 Unit box 105 x 95 x 58 1 cardboard 0.044 0.07
LRH1070 Outer box 400 x 300 x 300 42 cardboard 1.8 2.4
LCC1070 Unit box 90 x 90 x 90 1 plastic bag 0.13 0.17
LCC1070 Outer box 289 x 214 x 178 18 cardboard 2.4 2.7
Type MOQ Ordering number EAN code
level 1
EAN code
level 3
EOC
LRM1070/00 OccuSwitch basic 1 9137 003 27803 8711559 731384 8711559 731391 731384 99
LRM1080/00 OccuSwitch advanced 1 9137 003 27903 8711559 731407 8711559 731414 731407 99
LRH1070/00 Ceiling box 1 9137 003 28003 8711559 731438 8711559 731421 731438 99
LCC1070/00 Wieland cable 3p 1 9137 003 30303 8711559 731773 8711559 731780 731773 99
Data

© 2015-2016 Philips Lighting Holding B.V., all rights
reserved.
Specications are subject to change without notice.
Trademarks are the property of Philips Lighting Holding
B.V. or their respective owners.
3222 636 33176 6 October 2016
www.philips.com/controls