Philips AC3259 User manual

1 2
H I J K L M N
B
A
FDC
G
E
© 2018 Koninklijke Philips N.V.
All rights reserved.
4241 210 97493
AC3259
EN User manual 1
CS Příručka pro uživatele 18
HU Felhasználói kézikönyv 36
PL Instrukcja obsługi 55
RO Manual de utilizare 74
SK Príručka užívateľa 93
UK Посібник користувача 112

3s
3
11
7
15
3s
21
3s
19
5
13
9
17
23
6
14
10
18
24
4
12
8
16
3s
22
3s
20
25
3s
3s
29
33
36
27
3s
31
38
3s
32
3s
39
28
26
30
34
37
3s
35

1EN
English
Contents
1 Important 2
Safety 2
2 Your air purier 5
Product overview (g. a) 5
Controls overview (g. b) 5
3 Getting started 5
Installing lters 5
Wi-Fi setup 6
4 Using the appliance 7
Understanding the air
quality light 7
Switching on and o 7
Changing the Auto mode
setting 7
Changing the fan speed 8
Setting the timer 8
Setting the child lock 8
Using the light on/o function 9
Switching the display mode 9
5 Cleaning 9
Cleaning schedule 9
Cleaning the body of the
appliance 9
Cleaning the air quality
sensor 10
Cleaning the pre-lter 10
6 Replacing the lter 11
Understanding the healthy
air protect lock 11
Replacing the lters 11
Filter lifetime counter reset 12
Filter type change 12
7 Troubleshooting 13
8 Guarantee and service 16
Order parts or accessories 16
9 Notices 16
Electromagnetic elds (EMF) 16
Recycling 17
Software 17
Environmental friendly paper used. Thanks for your contribution to save trees.

2EN
1 Important
Safety
Read this user manual carefully before
you use the appliance, and save it for
future reference.
Danger
• Do not let water or any
other liquid or ammable
detergent enter the
appliance to avoid electric
shock and/or a re
hazard.
• Do not clean the
appliance with water,
any other liquid, or a
(ammable) detergent to
avoid electric shock and/
or a re hazard.
• Do not spray any
ammable materials
such as insecticides or
fragrance around the
appliance.
Warning
• Check if the voltage
indicated on the
appliance corresponds to
the local power voltage
before you connect the
appliance.
• If the power cord is
damaged, you must have
it replaced by Philips, a
service center authorized
by Philips, or similarly
qualied persons in order
to avoid a hazard.
• Do not use the appliance
if the plug, the power
cord, or the appliance
itself is damaged.
• This appliance can be
used by children aged
from 8 years and above
and persons with reduced
physical, sensory or
mental capabilities or
lack of experience and
knowledge if they have
been given supervision or
instruction concerning use
of the appliance in a safe
way and understand the
hazards involved. Child
shall not play with the
appliance. Cleaning and
maintenance shall not be
made by children without
supervision.
• Do not block the air inlet
and outlet, e.g. by placing
items on the air outlet or
in front of the air inlet.

3EN
English
• Make sure that foreign
objects do not fall into the
appliance through the air
outlet.
• Standard WiFi interface
based on 802.11b/g/n at
2.4 GHz with a maximum
output power of 31.62 mW
EIRP.
Caution
• This appliance is not
a substitute for proper
ventilation, regular
vacuum cleaning, or use
of an extractor hood or
fan while cooking.
• If the power socket used
to power the appliance
has poor connections,
the plug of the appliance
becomes hot. Make
sure that you plug the
appliance into a properly
connected power socket.
• Always place and use the
appliance on a dry, stable,
level, and horizontal
surface.
• Leave at least 20cm free
space behind and on both
sides of the appliance
and leave at least 30cm
free space above the
appliance.
• Do not place anything on
top of the appliance.
• Do not sit or stand on
the appliance. Sitting or
standing on the appliance
may lead to potential
injury.
• Do not place the
appliance directly below
an air conditioner to
prevent condensation
from dripping onto the
appliance.
• Make sure all lters
are properly installed
before you switch on the
appliance.
• Only use the original
Philips lters specially
intended for this
appliance. Do not use any
other lters.
• Combustion of the lter
may cause inreversible
human hazard and/or
jeopardize other lives . Do
not use the lter as fuel or
for similar purpose.
• Avoid knocking against
the appliance (the air inlet
and outlet in particular)
with hard objects.

4EN
• To prevent interference,
place the appliance at
least 2 meters away from
electrical appliances that
use airborne radio waves
such as TVs, radios, and
radio-controlled clocks.
• The appliance is only
intended for household
use under normal
operating conditions.
• Do not use the appliance
in wet surroundings or in
surroundings with high
ambient temperatures,
such as the bathroom,
toilet, or kitchen.
• The appliance does
not remove carbon
monoxide (CO) or radon
(Rn). It cannot be used
as a safety device in
case of accidents with
combustion processes
and hazardous chemicals.
• If you need to move the
appliance, disconnect the
appliance from the power
supply rst.
• Do not move the
appliance by pulling its
power cord.
• Always lift or move the
appliance by the handle
on top of the appliance.
• Do not insert your ngers
or objects into the air
outlet or the air inlet to
prevent physical injury
or malfunctioning of the
appliance.
• Do not use this appliance
when you have used
indoor smoke-type insect
repellents or in places
with oily residues, burning
incense, or chemical
fumes.
• Do not use the appliance
near gas appliances,
heating devices or
replaces.
• Always unplug the
appliance after use
and before cleaning
or carrying out other
maintenance.
• Do not use the appliance
in a room with major
temperature changes,
as this may cause
condensation inside the
appliance.

5EN
English
3 Getting started
Installing lters
Note
• Make sure the air purier is unplugged
from the electrical outlet before
installing the lters.
• Make sure that the side with the tag is
pointing towards you when installing
the lter.
1 Pull the bottom part of the front
panel to remove it from the
appliance (g. c).
2 Press the two clips down and pull
the pre-lter towards you (g. d).
3 Remove all lters (g. e).
4 Remove all packaging materials of
the air purication lters (g. f).
5 Put the unpacked air purication
lters back into the appliance
(g. g).
6 Put the pre-lter back into the
appliance (g. h).
Note
• Make sure that all hooks of the
pre-lter are properly attached to the
purier.
7 To reattach the front panel, mount
the panel onto the top of the
appliance rst (1). Then, gently push
the panel against the body of the
appliance (2) (g. i).
8 Wash your hands thoroughly after
installing lters.
2 Your air purifier
Congratulations on your purchase, and
welcome to Philips!
To fully benet from the support that
Philips oers, register your product at
www.philips.com/welcome.
Product overview (g. a)
AControl panel
BAir quality light
CAir quality sensors
DNanoProtect lter Series 3
(FY3433)
ENanoProtect lter AC (FY3432)
FPre-lter
GFront panel
Controls overview
(g. b)
HOn/O button
ILight on/o button
JAuto mode button
KDisplay screen
LFan speed button
MTimer button
NReset/Child lock button

6EN
Note
• This instruction is only valid when the
air purier is being set up for the rst
time. If the network has changed or the
setup needs to be performed again,
consult section "Setting up the Wi-Fi
connection when the network has
changed" on page 6.
• If you want to connect more than one
air purier to your smart device, you
have to do this successively. Complete
the set up of one air purier before you
turn on the other air purier.
• Make sure that the distance between
your mobile device and the air
purier is less than 10 m without any
obstructions.
• This app supports the latest versions
of Android and iOS. Please check
www.philips.com/purier-compatibility
for the latest update of supported
operating systems and devices.
Setting up the Wi-Fi connection
when the network has changed
Note
• This applies when the default network
to which your purier is connected has
changed.
1 Put the plug of the air purier in the
power socket and touch to turn
on the air purier.
2 Touch and simultaneously for
3 seconds until you hear a beep.
»The air purier goes to pairing
mode.
»The Wi-Fi indicator blinks
orange.
3 Follow the steps 4-5 in "Setting up
the Wi-Fi connection for the rst
time" section.
Wi-Fi setup
Setting up the Wi-Fi connection
for the rst time
1 Download and install the
'Air Matters' app from the App Store
or Google Play.
2 Put the plug of the air purier in the
power socket and touch to turn
on the air purier.
»The Wi-Fi indicator blinks
orange for the rst time.
3 Make sure that your mobile device
is successfully connected to your
Wi-Fi network.
4 Launch the 'Air Matters' app and
follow the onscreen instructions
to connect the air purier to your
network.
5 After the successful pairing and
connection, the Wi-Fi indicator
will light up white. If pairing
is not successful, consult the
troubleshooting section, or the
help section in the 'Air Matters'
app for extensive and up-to-date
troubleshooting tips.

7EN
English
3 Touch and hold for 3 seconds to
switch o the appliance.
Note
• After the appliance is switched o by
the on/o button , if the plug is still
in the power socket, the appliance will
operate under the previous settings
when it is switched on again.
• If the appliance is connected to
Internet after it's turned o, the sensor
will still measure the indoor air quality
and send this real-time data to the
app.
Changing the Auto mode
setting
You can choose the Pollution mode
( ), the Allergen mode ( ) and the
Bacteria & Virus mode ( ).
Pollution mode
The specially designed pollution
mode can eectively remove airborne
pollutants such as PM2.5.
• Touch the Auto mode button to
select the Pollution mode (g. l).
»A(Auto) and display on the
screen.
Allergen mode
The specially designed Allergen mode
can eectively remove common
allergens such as pollen and pet dander.
• Touch the Auto mode button to
select the Allergen mode (g. m).
»Auto(A) and display on the
screen.
4 Using the
appliance
Understanding the air
quality light
PM2.5
level
Air quality
light color
Air quality
level
≤12 Blue Good
13-35 Blue-Purple Fair
36-55 Purple-Red Poor
>55 Red Very poor
The air quality light automatically goes
on when the appliance is switched on,
and lights up all colors in sequence.
In a short time the air quality sensors
select the color that corresponds to the
ambient air quality.
Switching on and o
1 Put the plug of the appliance in the
power socket.
2 Touch to switch on the appliance
(g. j).
»The appliance operates under
the auto mode by default.
»After measuring the air quality
for a short time, the air quality
sensor automatically selects the
color of the air quality light.
»After measuring the particle
matters in the air, the air purier
shows the PM2.5 level and
operates in the auto mode with
displayed on the screen
(g. k).

8EN
Bacteria/Virus mode
The specially designed Bacteria & Virus
mode can eectively remove bacteria
& viruses such as staphylococcus albus
and H1N1.
• Touch the Auto mode button to
select the Bacteria & Virus mode
(g. n).
»Auto(A) and display on the
screen.
Changing the fan speed
There are several fan speeds available.
You can choose the sleep mode ( ),
turbo mode ( ) and speed 1, 2, or 3.
Sleep (SL)
In sleep mode, the appliance operates
quietly under speed 1. One minute into
the sleep mode, the power and light
on/o indicators are dimmed, and all
the other lights are o.
• Touch the fan speed button to
select the sleep mode ( ) (g. o).
Manual
• Touch the fan speed button
repeatedly to select the fan speed
you need (g. p).
Turbo (t)
In turbo mode, the appliance operates
under the highest speed.
• Touch the fan speed button to
select the turbo mode ( ) (g. q).
Setting the timer
With the timer, you can let the
appliance operate for a set number of
hours. When the set time has elapsed,
the appliance will automatically switch
o.
• Touch the timer button
repeatedly to choose the number
of hours you want the appliance to
operate (g. r).
»The timer is available from 1to
12 hours.
To deactivate the timer, touch the timer
button repeatedly until displays
on the screen.
Setting the child lock
1 Touch and hold the child lock
button for 3 seconds to activate
child lock (g. s).
»displays on the screen.
»When the child lock is on,
all the other buttons are not
responsive.
2 Touch and hold the child lock
button for 3 seconds again to
deactivate child lock (g. t).
»disappears from the screen.
Note
• You can still control the air purier
through the App e ven child lock is
activated.

9EN
English
Using the light on/o
function
With the light on/o button, you can
switch on or o the air quality light,
the display screen and the function
indicators if needed.
1 Touch the light on/o button
once, the air quality light, the
display screen and the function
indicators will go o.
2 Touch the light on/o button
again, all lights will be on.
Switching the display
mode
The air purier has two display modes:
PM2.5 display mode and IAI (Indoor
Allergen Index) display. In PM2.5 mode
the display shows the particulate matter
2.5 concentration in the air in µg/m3.
When in IAI mode, the display shows
a number between 1-12 to indicate the
level of airborne allergens.
Note
• The air purier operates in PM2.5
display mode by default.
1 Touch the light dimming button
for 3 seconds again to switch to IAI
display mode (g. u).
»The IAI level displays on the
screen.
2 Touch the light dimming button
for 3 seconds to switch back to
PM2.5 display mode (g. v).
»The actual PM2.5 level displays
on the screen.
5 Cleaning
Note
• Always unplug the appliance before
cleaning.
• Never immerse the appliance in water
or any other liquid.
• Never use abrasive, aggressive, or
ammable cleaning agents such as
bleach or alcohol to clean any part of
the appliance.
• Only the pre-lter is washable. The air
purication lter is not washable nor
vacuum cleanable.
Cleaning schedule
Frequency Cleaning method
When necessary Wipe the surface
of the appliance
with a soft dry
cloth
When F0
displays on the
screen
Clean the pre-
lter
Every two
months
Clean the air
quality sensors
Cleaning the body of the
appliance
Regularly clean the inside and outside
of the appliance to prevent dust from
collecting.
1 Wipe away dust with a soft dry cloth
from the body of the appliance.
2 Clean the air outlet with a soft dry
cloth.

10 EN
Cleaning the pre-lter
Clean the pre-lter when F0 is displayed
on the screen(g. {).
1 Pull the bottom part of the front
panel to remove it from the
appliance (g. c).
2 Press the two clips down and pull
the pre-lter towards you (g. d).
3 Wash the pre-lter under a running
tap. If the pre-lter is very dirty, use
a soft brush to brush away the dust
(g. |).
4 Air dry the pre-lter.
Note
• Make sure that the pre-lter is
completely dry. If it is still wet, bacteria
may multiply in it and shorten the
lifetime of the pre-lter.
5 Put the pre-lter back into the
appliance (g. h).
Note
• Make sure that the side with the two
clips is pointing towards you, and that
all hooks of the pre-lter are properly
attached to the purier.
6 To reattach the front panel, mount
the panel onto the top of the
appliance rst (1). Then, gently push
the panel against the body of the
appliance (2) (g. i).
7 Touch and hold the reset button
for 3 seconds to reset the pre-lter
cleaning time (g. }).
Cleaning the air quality
sensor
Clean the air quality sensor every
2 months for optimal functioning of the
purier. Clean them more frequently
if you use the purier in a dusty
environment.
Note
• When the humidity level in the
room is very high, it is possible that
condensation develops on the air
quality sensor. As a result, the air
quality light may indicate that the air
quality is bad even though it is good.
In this case you have to clean the
air quality sensor or use one of the
manual speed settings.
1 Clean the air quality sensor inlet
and outlet with a soft brush (g. w).
2 Open the air quality sensor cover
(g. x).
3 Clean the air quality sensor, the
dust inlet and the dust outlet with a
lightly moistened cotton swab
(g. y).
4 Dry them with a dry cotton swab.
5 Reattach the air quality sensor
cover (g. z).

11EN
English
6 Replacing the
filter
Understanding the
healthy air protect lock
This air purier is equipped with a
lter replacement indicator to make
sure that the air purication lter is in
optimal condition when the air purier
is operating. When the lters need to be
replaced, the lter code displays on the
screen (see Filter alert chart).
If the lters are not replaced in time,
the air purier will stop operating and
automatically lock to protect the air
quality in the room. Replace the lters
as soon as possible according to the
lter code.
Replacing the lters
Note
• The air purication lters are not
washable nor vacuum cleanable.
• Always turn o the air purier and
unplug from the electrical outlet
before replacing the lters.
• Do not clean the lters with a with a
vacuum cleaner.
• If the pre-lter is damaged, worn or
broken, do not use. Visit
www.philips.com/support or contact
the Consumer Care Center in your
country.
Filter alert chart
Filter alert light
status Follow this
A3 displays on the
screen
Replace
NanoProtect
lter Series 3
(FY3433)
C7 displays on the
screen
Replace the
NanoProtect
lter AC
(FY3432)
A3 and C7 display
on the screen
alternately
Replace both
lters
1 Take out the used air lters
according to the lter code
displayed on the screen. Discard
used lters (g. ~).
Note
• Do not touch the pleated lter surface,
or smell the lter as it has collected
pollutants from the air.
2 Remove all packaging material of the
new lters (g. f).
3 Place the new lters into the
appliance (g. g).
4 Put the plug of the appliance in the
power socket.
5 Touch and hold the reset button
for 3 seconds to reset the lter
lifetime counter (g. ).
Note
• Wash your hands after changing the
lters.

12 EN
Note
• After you have selected the lter code
of the new lter using the button,
if you do not touch any other buttons
in 10 seconds, the appliance will
automatically conrm the lter code of
the new lter.
4 Code (C7) of the Nanoprotect lter
AC displays on the screen after the
rst lter type has been changed
(g. ‚).
5 Touch to select the new lter
code of the second lter (g. †).
6 Touch and hold for 3 seconds to
conrm the lter code of the second
lter and exit the lter type change
mode (g. ‡).
Filter lifetime counter
reset
After replacing a lter, you need to reset
the lter lifetime counter manually.
You can also replace lters even if there
is no lter replacement code displayed
on the screen.
1 Touch and simultaneously for
3 seconds to enter the lter force
reset mode (g. €).
»Code (A3) of the NanoProtect
lter Series 3 displays on the
screen .
2 Touch and hold for 3 seconds to
force reset the lter lifetime of the
NanoProtect lter Series 3 (g. ).
3 Code (C7) of the Nanoprotect lter
AC displays on the screen after the
lifetime of the NanoProtect lter
Series 3 lter has been reset
(g. ‚).
4 Touch and hold for 3 seconds to
force reset the lter lifetime of the
NanoProtect lter AC and exit the
lter force reset mode (g. ƒ).
Filter type change
1 Touch and simultaneously for
3 seconds to enter the lter type
change mode (g. €).
»Code (A3) of the NanoProtect
lter Series 3 displays on the
screen.
2 Touch to select the lter code of
the new lter you will use (g. „).
3 Touch and hold for 3 seconds to
conrm the lter code of the new
lter (g. …).

13EN
English
7 Troubleshooting
This chapter summarizes the most common problems you could encounter with the
appliance. If you are unable to solve the problem with the information below, contact
the Consumer Care Center in your country.
Problem Possible solution
The appliance
does not work
even though it is
plugged in.
•Check if the front cover is properly installed.
•The lter replacement code has been displaying on the
screen but you have not replaced the corresponding lter
yet. The appliance will be locked if you keep using the
expired lter. In this case, replace the lter and reset the
lter lifetime counter.
The appliance
does not work
even though it is
switched on.
•The appliance is working but the buttons are not
responsive. Check if the child lock is on.
•The lter replacement code has been on continuously but
you have not replaced the corresponding lter, and the
appliance is now locked. In this case, replace the lter and
reset the lter lifetime counter.
The airow that
comes out of
the air outlet
is signicantly
weaker than
before.
•The pre-lter is dirty. Clean the pre-lter (see chapter
"Cleaning").
The air quality
does not improve,
even though the
appliance has
been operating for
a long time.
•Check if the packing material is removed from the lters.
•One of the lters has not been placed in the appliance.
Make sure that all lters are properly installed in the
following order, starting with the innermost lter:
1) NanoProtect lter Series 3; 2) NanoProtect lter AC;
3) pre-lter.
•The air quality sensor is wet. The humidity level in your
room is high and causes condensation. Make sure that the
air quality sensor is clean and dry (see chapter "Cleaning").
The color of the air
quality light always
stays the same.
•The air quality sensor is dirty. Clean the air quality sensor
(see chapter "Cleaning").

14 EN
Problem Possible solution
The appliance
produces a strange
smell.
•The lter may produce smell after being used for a
while because of the absorption of indoor gases. It’s
recommended that you reactivate the lter by putting it in
direct sunlight for repeated use. If odor still exists, replace
the lter.
•If the air purier produces a burnt odor, switch OFF and
unplug from the electrical outlet. Contact Consumer Care
Center in your country.
The appliance is
extra loud.
•If the appliance is too loud, you can change the fan speed
to a lower fan speed level. When using the appliance in a
bedroom at night, choose the sleep mode.
The appliance still
indicates that I
need to replace a
lter, but I already
did.
•Perhaps you did not reset the lter lifetime counter. Plug
in the appliance, touch to switch on the appliance, and
touch and hold the reset button for 3 seconds.
Error codes "E1",
or "E2" displays on
the screen.
•The appliance has malfunctions. Contact the Consumer
Care Center in your country.
Which App should
I download?
•Please download and install the 'Air Matters' app from the
App Store or Google Play.

15EN
English
Problem Possible solution
The Wi-Fi setup is
not successful.
•If the router your purier is connected to is dual-band and
currently it is not working on a 2.4GHz network, please
switch to another band of the same router (2.4GHz) and
try to pair your purier again. 5Ghz networks are not
supported.
•Web authentication networks are not supported.
•Check if the purier is within range of the Wi-Fi router. You
can try to locate the air purier closer to the Wi-Fi router.
•Check if the network name is correct. The network name is
case-sensitive.
•Check if the Wi-Fi password is correct. The password is
case-sensitive.
•Retry the setup with the instructions in section ‘Set up the
Wi-Fi connection when the network has changed’.
•The Wi-Fi connectivity can be interrupted by electromagnetic
or other interferences. Keep the appliance away from other
electronic devices that may cause interferences.
•Check if the mobile device is in airplane mode. Make sure
to have the airplane mode deactivated when connecting
to the Wi-Fi network.
•Consult the help section in the App for extensive and up-
to-date troubleshooting tips.

16 EN
9 Notices
Electromagnetic elds
(EMF)
This Philips appliance complies with all
applicable standards and regulations
regarding exposure to electromagnetic
elds.
Compliance with EMF
Koninklijke Philips N.V. manufactures
and sells many products targeted at
consumers, which, like any electronic
apparatus, in general have the ability
to emit and receive electromagnetic
signals.
One of Philips' leading Business
Principles is to take all necessary health
and safety measures for our products,
to comply with all applicable legal
requirements and to stay well within the
EMF standards applicable at the time of
producing the products.
Philips is committed to develop,
produce and market products that
cause no adverse health eects. Philips
conrms that if its products are handled
properly for their intended use, they
are safe to use according to scientic
evidence available today.
Philips plays an active role in the
development of international EMF
and safety standards, enabling Philips
to anticipate further developments in
standardization for early integration in
its products.
8 Guarantee and
service
If you need information or if you have a
problem, please visit the Philips website
at www.philips.com or contact the
Philips Consumer Care Center in your
country (you nd its phone number
in the worldwide guarantee leaet). If
there is no Consumer Care Centre in
your country, go to your local Philips
dealer.
Order parts or
accessories
If you have to replace a part or want to
purchase an additional part, go to your
Philips dealer or visit
www.philips.com/support.
If you have problems obtaining the
parts, please contact the Philips
Consumer Care Center in your country
(you can nd its phone number in the
worldwide guarantee leaet).

17EN
English
Recycling
This symbol means that this product
shall not be disposed of with normal
household waste (2012/19/EU).
Follow your country’s rules for the
separate collection of electrical and
electronic products. Correct disposal
helps prevent negative consequences
for the environment and human health.
Software
App Store is a service mark of Apple Inc.
Google Play is a trademark of Google
Inc.
This Philips appliance and Air Matters
app applied multiple open source
softwares, copies of open source
software license text used in this
product can be derived from website:
www.philips.com/purier-compatibility.

18 CS
Obsah
1 Důležité 19
Bezpečnost 19
2 Vaše čistička vzduchu 22
Přehled výrobku (obr. a) 22
Přehled ovládacích prvků
(obr. b) 22
3 Začínáme 22
Instalace ltrů 22
Nastavení Wi-Fi 23
4 Použití přístroje 24
Jak funguje kontrolka kvality
vzduchu 24
Zapnutí a vypnutí 24
Změna nastavení
automatického režimu 24
Změna rychlosti ventilátoru 25
Nastavení časovače 25
Nastavení dětské pojistky 25
Používání funkce zapnutí/
vypnutí osvětlení 26
Zapnutí režimu zobrazení 26
5 Čištění 27
Plán čištění 27
Čištění těla přístroje 27
Čištění snímače kvality
vzduchu 27
Čištění předltru 28
6 Výměna ltru 28
Jak funguje zámek ochrany
zdravého vzduchu 28
Výměna ltrů 28
Resetování počítadla
životnosti ltru 29
Změna typu ltru 29
7 Odstraňování problémů 31
8 Záruka a servis 34
Objednání dílů nebo
doplňků 34
9 Upozornění 34
Elektromagnetická pole
(EMP) 34
Recyklace 35
Software 35
S použitím papíru šetrného k přírodě Děkujeme, že pomáháte chránit stromy