Philips CID3681/93 User manual

www.philips.com/welcome
Register your product and get support at CID3681
ENG Quick Start Guide

1
a
g
h
i
j
b
c
d
e
f
a
b

c
Red
White
Yellow
Red
Red White
Yellow
Black Black
Yellow
Yellow Green
White
Amplifier
White
Brown
Red Red

2
3

4
a
c
b

5
6

English
Install the car audio
These instructions are for a typical installation.
However, if your car has different requirements,
make the corresponding adjustment. If you have
any questions regarding installation kits, consult
your Philips car audio dealer.
Caution
This unit is designed for negative ground

(earth) 12 V DC operation only.
Always install this unit in the car dashboard.

Other locations can be dangerous as the rear
of the unit heats up during use.
To avoid short-circuit: before you connect,

ensure that the ignition is off.
Ensure that you connect the yellow and red

power supply leads after all other leads are
connected.
Ensure that all loose leads are insulated with

electrical tape.
Ensure that the leads do not get caught under

screws orin parts that will move (e.g. seat rail).
Ensure that all ground (earth) leads are run to

a common ground (earth) point.
Use only the supplied mounting hardware for

a safe and secure installation.
,PSURSHUIXVHVFDQFDXVHGDPDJHRUÀUH

When you need to change the fuse, consult
a professional.
Note on the power supply lead (yellow)
When you connect other devices to this
system, ensure that the rating of the car
circuit is higher than the total fuse value
of all the connected devices.
Notes on speaker connection
Never connect speaker wires to the metal
body or chassis of the car.
Never connect speaker wires with stripes
to one another.
Connect wires 1
Caution
Ensure that all loose leads are insulated with

electrical tape.
1Check the car's wiring carefully, then connect
them to the two supplied ISO wires. a
Connector Connect to
1Brown/black
wire
Connect to CAN box/L
2Brown wire Telephone mute
3Red wire The +12V power terminal
which is live in the accessory
(ACC) position ofthe
ignition switch
If there is no accessory
position, connect to the
+12V car battery terminal
that is always live. Be sure
to connect the black ground
(earth) lead to a metal
VXUIDFHRIWKHFDUÀUVW
4Orange/
white wire
Connect to CAN box/H
5Black wire A metal surface ofthe car
First connect the black
ground (earth) lead, then
connect the yellow and red
power supply leads.
6Yellow wire The +12V car battery
which is live at all times.
7Green and
green/black
wires
Left speaker (Rear)
8White and
white/black
wires
Left speaker (Front)
9Gray and
gray/black
wires
Right speaker (Front)

0Purple and
purple/black
wires
Right speaker (Rear)
2Connect the other end of the two ISO
connectors to the car audio system. b
3If necessary, do the other connections. c
Connect GPS antenna 2
To receive signal from satelite, you need to connect
the supplied GPS antenna to your car and the
system.
1Connect the supplier GPS antenna to the
V\VWHPÀUVW
2Stick the other end of the GPS antenna to a
surface for signal reception.
Connect radio antenna 3
If your car has built-in radio antenna, connect it to
the radio antenna of the system for better radio
signal.
1Connect the radio antenna to the car
antenna.
Mount in the dashboard 4
Note
Check wire connection before you mount

the unit into a car.
1Install the tracks to the unit with the supplied
screws. a
2Remove the trim plate and slide the unit
along the guide track into the car. b
3Fix the unit to the dashboard with screws
(supplied by the car manufacturer). c
4Attach the trim plate.
5Reconnect the negative terminal of the car
battery.
Turn on
Caution
Risk of road accidents! Never watch video or

adjust settings while you drive.
1Press and hold /MUTE/VOL to turn on the
unit.
The available OSD (On-Screen Display)
»
languages are displayed.
2Touch a language to select.
The OSD language is changed to the
»
selected language immediately.
To turn off the unit, press and hold /MUTE/
VOL.
Set date and time
1Touch the upper left corner to display main
menu.
2Touch in the middle right side of the screen.
The second main menu is displayed.
»
3Touch [Settings].
4Touch [Time].

The date/time setup menu is displayed.
»
Set date
1Touch [Date].
2Touch on the displayed date information.
A submenu is displayed.
»
3Touch or to set year, month and day.
Set clock mode
1Touch [Clock mode].
2Touch on [12Hr] or [24Hr] to select clock
mode.
Set time
1Touch [Time].
2Touch on the displayed time.
A submenu is displayed.
»
3Touch or to set hour and minute.
Tip
When date/time is set, touch
ÀUVWDQG
then touch to return to main menu.
Use map
Note
You may need to upgrade the map before

using it (see “Upgrade the map” section)
1Touch the upper left corner to display home
menu.
2Touch [Navigation].
The navigation menu is displayed in a few
»
seconds.
3Refer to the map manual (in Chinese) to
operate the navigation tool.
Tip
You can press
NAVI to enter/exit the
navigation system.
Tune to a radio station
1Touch the upper left corner to display home
menu.
2Touch [Radio].
Band and frequency information is displayed.
»
3Touch on FM or AM to select band:
FM band options: FM1, FM2, FM3
AM band options: AM1, AM2

4 %ULHÁ\WRXFK or to tune to a radio station
by step.
Touch or for over 1 seconds to tune
to a radio station automatically.
Load discs 5
You can play video, audio or images stored on the
following discs:
DVD video, DVD-R, DVD-RW
VCD
Audio CD, CD-R, CD-RW
Note
Ensure that the disc contains playable
content.
1Insert the disc into the disc slot with label
side facing up.
Play starts automatically.
»
To remove the disc, press the
»button.
When the disc is ejected, the unit
»
switches to the previous source, if
connected. Otherwise, the unit switches to
[Radio] mode automatically.
Connect USB device 6
Note
Ensure that the device contains playable

content.
1Open the USB door.
2Insert your USB device to the USB socket.
Play starts automatically.
»
Pair the Bluetooth-enabled
devices
To connect your Buetooth device to the unit, you
need to pair the device to the unit. Pairing needs
only to be done once.You can pair up to eight
devices.
1Turn on the Bluetooth function on the device.
2Search for Bluetooth device with the device.
3Select “CID3681” in the pairing list.
4Enter default password “0000”.
If pairing succeeds. phone call record is
»
displayed.
Make a call
1Pair the phone with the unit.
2Touch the upper left corner to display the
home menu.
3Touch [Bluetooth].
The Bluetooth menu is displayed.
»

4Touch or to select the paired phone,
then touch .
5Touch or to search for phone number
from the following list:
Or touch to dial number directly, then touch
to dial.
Receive call
By default, all incoming calls are received
automatically.
1If there is incoming call, [Incoming call...]
ÁDVKHVRQWKHVFUHHQ6SHDNLQWRWKH
Bluetooth microphone.
2When conversation ends, touch (red) to
terminate the call.
Tip
You can select to receive calls manually by

set [Auto answer] to [Off]status.
Adjust sound
Adjust volume
1Turn /MUTE/VOL clockwise to increase
volume.
Turn /MUTE/VOL anti-clockwise to reduce
volume.
Mute
1During play, press /MUTE/VOL.
To turn the sound back on, press
/MUTE/VOL again.
Tip
You can also turn off sound by touching
on the screen.
Select preset equalizer
You can select preset equalizer:
1Touch anywhere except for the upper left
corner to display menu on the screen, if
necessary.
2Touch .
The current Equalizer setting is displayed.
»

3Touch or to select an EQ.
4Touch or to adjust below settings:
 [Bass]bass range: -14 to +14.
 [Mid]middle range: -14 to +14.
 [Treb]treble range: -14 to +14.
 [LPH]ORZSDVVÀOWHUUDQJH
60, 80, 100, 200.
 [MPF]PLGGOHSDVVÀOWHUUDQJH
500, 1K, 1.5K, 2.5K.
 [HPF]KLJKSDVVÀOWHUUDQJH
10K, 12.5K, 15K, 17.5K.
5Touch to restore the above settings into
default settings.
6Press to exit.
© 2009 Koninklijke Philips Electronics N.V.
All rights reserved.
CID3681_93_QSG_V1.0