Philips Aed Trainer 3 User manual

861467
Edition 2
AED Trainer 3
INSTRUCTIONS FOR USE
453564382981

PHILIPS MEDICAL SYSTEMS
H
G
A
B
E
D
F
C
I
K
J
A. Training Pads Connector Socket —
Receptacle for the training pads connector plug.
B. Pads Connector LED — Flashes to indicate
the socket location when device is turned on.
Inserted pads connector plug covers the LED,
which stops flashing when connector plug is
properly seated.
C. Remote Control Receiver Window —
Receives signals from the optional remote
control.
D. Speaker — Delivers voice instructions from
the AED Trainer 3. Speaker volume can be
adjusted with the remote control or set in the
device configuration.
E. Connector — For future use.
F. Green Ready Light — Illuminates when the
AED Trainer 3 is turned on; flashes when device is
receiving commands from the remote control;
stays off when the device is not in use.
G. Infant/Child Key Port — Receptacle for the
Training Infant/Child Key. When Key is inserted,
the AED Trainer 3 operates in Infant/Child mode
to simulate defibrillation of an infant or child
under 8 years old or 25 kg (55 lbs).
H. Green On/Off Button — Turns on the AED
Trainer 3 and starts voice instructions.
I. Orange Shock Button — Controls delivery
of simulated shock. The button flashes when a
shock is advised during a scenario.
J. Battery Compartment — Contains the four
replaceable AA size alkaline batteries (not
provided) used to power the AED Trainer 3.
K. Operating System Card — Contains the
Trainer operating system, all voice commands, and
device configuration. The Operating System Card
must be installed in the AED Trainer 3 to use the
device.
AED TRAINER 3 USER INTERFACE

PHILIPS MEDICAL SYSTEMS
AED Trainer 3
861467
Edition 2
INSTRUCTIONS FOR USE

PHILIPS MEDICAL SYSTEMS
About this edition
The information in this guide applies to the AED
Trainer 3 model 861467. This information is
subject to change. Please contact Philips at
www.philips.com/productdocs or your local
Philips representative for information on
revisions.
Edition history
Edition 2
Publication date: February 2013
Publication number: 453564382981
Copyright
© 2013 Laerdal Medical AS. All Rights Reserved.
Device Manufacturer
Laerdal Medical AS
Tanke Svilandsgate 30
N-4002 Stavanger, Norway
For Technical Support
If you need technical support, please contact your
local Philips representative or go to
www.philips.com/AEDsupport.

PHILIPS MEDICAL SYSTEMS
CONTENTS
INTRODUCTION
Description and Intended Use ...................................................... 1
Features .............................................................................................. 1
HOW SUPPLIED
Standard Package Contents ........................................................... 2
Optional Accessories ...................................................................... 3
SETTING UP THE AED TRAINER 3
Checking the Operating System Card ........................................ 4
Installing the batteries ..................................................................... 4
Selecting a Language ........................................................................ 5
Changing the Configuration ........................................................... 6
Connecting the Training Pads ....................................................... 7
Accessing the Training Infant/Child Key ..................................... 9
USING THE AED TRAINER 3
Preparing to use the AED Trainer 3 ........................................... 10
Selecting a training scenario .......................................................... 11
Running a Training Scenario .......................................................... 12
Using the Optional Remote Control .......................................... 12
APPENDICES
Parameter Settings ........................................................................... 15
Training Scenarios ............................................................................ 17
Remote Control ............................................................................... 19
Troubleshooting Tips ...................................................................... 21
Specifications ..................................................................................... 23
Regulatory Information ................................................................... 24
Glossary of Symbols ........................................................................ 25

PHILIPS MEDICAL SYSTEMS
INTENTIONALLY BLANK

1
PHILIPS MEDICAL SYSTEMS
INTRODUCTION
DESCRIPTION AND INTENDED USE
The model 861467 AED Trainer 3 is designed to prepare emergency
responders to use the HeartStart FR3 automatic external defibrillator (AED)
and other AEDs. Together with appropriate manikins, the AED Trainer 3 is
intended to give realistic training on delivering correct treatment, including
shock delivery and CPR, to a cardiac arrest victim.
The AED Trainer 3 provides eight training scenarios that simulate realistic
episodes of sudden cardiac arrest (SCA) and help responders become familiar
with use of the HeartStart FR3 AED in an emergency. These scenarios are
compatible with training programs developed by internationally recognized
responder programs.
The AED Trainer 3 is shipped with a factory default setup that complies with
the ERC (European Resuscitation Council) and AHA (American Heart
Association) 2010 Guidelines. The device may also be configured to conform
to local protocols or Guideline Updates.
NOTE: Before using the HeartStart FR3 Defibrillator, the responder should
have completed an appropriate responder training program, which may
include the use of the AED Trainer 3. Having completed such a course, the
responder should demonstrate a proficiency in assessing the patient for
lack of responsiveness and absence of breathing, cardiopulmonary
resuscitation (CPR), and knowledge of applicable medical protocols and
procedures.
FEATURES
The AED Trainer 3 is designed to replicate the operation of the HeartStart
FR3 AED. However, it has no high-voltage capabilities, ensuring safety during
training. It provides simulated shock delivery.
The AED Trainer 3 can be used to provide training on the following key
features of the HeartStart FR3 AED:

PHILIPS MEDICAL SYSTEMS
2
• Fast delivery of therapy. The AED Trainer 3 carry case duplicates the
auto-on feature of the FR3 rigid system case. When the case is opened,
the AED Trainer 3 automatically turns on.
• Pre-connected pads. Like the FR3 AED, the AED Trainer 3 uses pre-
connected pads to help optimize response time.
• Infant/Child Key. The AED Trainer 3 comes with a Training Infant/Child
Key to replicate the infant/child mode of the FR3 AED.
• Voice prompts. The AED Trainer 3 guides you through each step of the
training scenario with the same voice prompts as the FR3 AED.
• Extensive configurability. Like the FR3 AED, the AED Trainer 3
configuration can be customized and its operation easily updated as
needed.
NOTE: The Training Infant/Child Key cannot be used with the HeartStart
FR3 AED. An FR3 Infant/Child Key is required for use with the AED.
HOW SUPPLIED
STANDARD PACKAGE CONTENTS
The AED Trainer 3 is shipped with the following items as standard:
• one AED Trainer 3
• one Carry Case
• one Training Infant/Child Key, pre-installed on tether in carry case
• one External Manikin Adapter
• one pre-installed AED Trainer 3 Operating System Card containing the
AED Trainer 3 operating system and Configuration program
• one reusable HeartStart Training Pads III interconnect cable
• one set of reusable HeartStart Training Pads III

3
PHILIPS MEDICAL SYSTEMS
•oneprinted Instructions for
Use
in English and Japanese
• one CD-ROM containing
Instructions for Use in
additional languages and
Configuration program
• one multi-language Quick
Start Guide
• one set of “Training Only”
stickers in multiple languages
OPTIONAL ACCESSORIES
The following accessories are available separately for use with the AED
Trainer 3:
• Remote Control, with one replaceable lithium CR2025 3V battery
[REF: 989803171631]
• Replacement HeartStart Training Pads III Interconnect Cable
[REF: 989803150201]
• Replacement HeartStart Training Pads III [REF: 989803150181]
• Replacement External Manikin Adapters, set of 5 [REF: M5089A]
• Laerdal LINK Technology Training Pads [REF: M3755A] for use with
compatible Laerdal manikins
TRAINING TRAINING
Carry Case
PhilipsTraining Pads III
NOTFOR
CLINICAL USE
CL
INIC
Reusable Training Pads III
Interconnect cable
Training infant/child key
with tether
Operating
System Card
AEDTrainer 3
i
f
t
f

PHILIPS MEDICAL SYSTEMS
4
SETTING UP THE AED TRAINER 3
To set up the AED Trainer 3 for operation, you will need to ensure that the
Operating System Card is properly installed, install the batteries (not
provided), select a different language if you do not wish to use U.S. English,
and connect the training pads. Instructions for each of these tasks follow.
CHECKING THE OPERATING SYSTEM CARD
The AED Trainer 3 Operating System Card contains the operating system for
the AED Trainer 3. The AED Trainer 3 is shipped with the Operating System
Card pre-installed. To remove, re-install, or replace the Operating System
Card, follow the steps below:
1. Squeeze the latch on the battery
compartment lid to release the lid. Lift out
the lid and set it aside.
2. Check that the Operating System Card is
installed in the slot at the top of the
compartment. If not, install the Operating
System Card in the orientation shown.
INSTALLING THE BATTERIES
The AED Trainer 3 requires four AA size
alkaline batteries (not included). To install or
replace the batteries in the AED Trainer 3,
follow the steps below:
1. Squeeze the latch on the battery compartment lid to release the lid. Lift
out the lid and set it aside.
2. Install four AA size alkaline batteries in the battery compartment
oriented as illustrated inside the compartment.
NOTE: Use only fresh batteries of the same type.
3. Replace the battery compartment lid.
4. Return the AED Trainer 3 to its case.

5
PHILIPS MEDICAL SYSTEMS
SELECTING A LANGUAGE
The default language of the AED Trainer 3 is U.S. English. To set up the AED
Trainer 3 for another language, follow the steps below.
1. Press and hold both the green On/Off button and the orange Shock
button for about three seconds. The AED Trainer 3 announces the
default language, “U.S. English.”
2. Release both buttons.
3. Press and hold the orange Shock button to scroll through each available
language. The AED Trainer 3 announces each new language.
4. When the desired language is announced, press the green On/Off button
to turn off the AED Trainer 3 and store the selected language. The AED
Trainer 3 will use this language when it is next turned on.*
5. Apply the appropriate “Training Only” sticker for the language selected,
as illustrated below.
* The AED Trainer 3 can be turned on by pressing either the On/Off button or the
shock button.

PHILIPS MEDICAL SYSTEMS
6
CHANGING THE CONFIGURATION
The AED Trainer 3 is shipped with a configuration replicating the default
factory settings of the FR3 AED. If you want to change the AED Trainer 3
configuration to match local protocols or for other training purposes, follow
the steps below:
1. Squeeze the latch on the battery compartment lid to release the lid. Lift
out the lid and set it aside.
2. Remove the Operating System Card from the slot at the top of the
compartment.
3. Insert the Operating System Card into the card slot of your computer or,
if no slot is available, install the card into a standard card reader and
connect it to your computer.
4. Open the AED Trainer 3 Configuration program (Aedt3Cfg.exe) and
select the desired language for use during configuration.
5. Click “Open,” and go to the drive with Operating System Card.
6. Click on “System” and then on “Config” and then open the “Config.Dat”
file to load the existing Trainer 3 setup to the program.
7. Adjust the parameter settings as desired. See page 15 for detailed
information about the available settings.
POUR LA FORMATION UNIQUEMENT
SOLO PER ADDESTRAMENTO
SÓLO ENTRENAMIENTO
Ó
L
O
E
N
T
R
E
N
A
M
I
E
N
T
O

7
PHILIPS MEDICAL SYSTEMS
8. After making all desired changes, click on “Update.”
9. Click “Exit” to close the configuration program.
10. Remove the Operating System Card from the computer or card reader
and replace it in the AED Trainer 3. See page 4 for directions on installing
the card. The AED Trainer 3 configuration will be updated automatically
the next time the AED Trainer 3 is turned on.
CONNECTING THE TRAINING PADS
The AED Trainer 3 may be used with either HeartStart Training Pads III or
Laerdal LINK Technology Training Pads.
HEARTSTART TRAINING PADS III
To connect the HeartStart Training Pads III to the AED Trainer 3, follow the
steps below.

PHILIPS MEDICAL SYSTEMS
8
1. Remove the HeartStart Training Pads III from their storage bag, leaving
them on their liner.
2. Remove the interconnect cable from its storage bag. Connect the pads
cable to the interconnect cable.
3. Plug the interconnect cable’s yellow connector into the pads connector
socket on the front of the AED Trainer 3. Be sure the connector clicks
into place.
4. Place the AED Trainer 3 with the pre-connected pads in the carry case.
The case is designed to store the AED Trainer 3 with the pads pre-
connected.
The HeartStart Training Pads III are designed for up to 100 uses. To help
ensure continued performance, avoid leaving the pads in heat or direct
sunlight. To replace the pads, disconnect the connector plug from the AED
Trainer 3 and repeat Steps 1 through 3, above.
LAERDAL LINK TECHNOLOGY TRAINING PADS
To connect the Laerdal LINK Technology Training Pads to the AED Trainer 3,
follow the steps below.
1. Remove the Laerdal LINK Technology Training Pads from their storage
bag, leaving them on their liner.
NOT FOR
CLINICAL USE
NOT FOR
CLINICAL
USE
TRAINING
TRAINING

9
PHILIPS MEDICAL SYSTEMS
2. Plug the pads connector into the pads connector socket on the front of
the AED Trainer 3. Be sure the connector clicks into place.
3. Place the AED Trainer 3 with the pre-connected pads in the carry case.
The case is designed to store the AED Trainer 3 with the pads pre-
connected.
ACCESSING THE TRAINING INFANT/CHILD KEY
The Training Infant/Child Key is supplied on a tether pre-installed in the AED
Trainer 3 carry case. To access the Training Infant/Child Key for use, remove it
from its compartment in the case lid, and extend the tether to insert the Key
into the Infant/Child Key port on the AED Trainer 3.
OK
   
  
%)(8VEMRIV

PHILIPS MEDICAL SYSTEMS
10
NOTE: Do not store the Training Infant/Child Key installed in the AED
Trainer 3. Install the Training Infant/Child Key in the AED Trainer 3 only
when teaching defibrillation of infants or children under 8 years old or
55 lbs (25 kg).
USING THE AED TRAINER 3
PREPARING TO USE THE AED TRAINER 3
Before turning on the AED Trainer 3, follow the steps below:
1. Check that the pads are pre-connected as described on page 7. If no
training pads are connected when the AED Trainer 3 is turned on, the
AED Trainer 3 will provide a voice instruction to place the pads on the
patient’s bare chest and then plug in the pads connector by the flashing
light.
2. If you are using HeartStart Training Pads III, attach the external manikin
adapter provided to the skin of the training manikin as shown below.
3. Place the pads on the adapter as shown.
1234

11
PHILIPS MEDICAL SYSTEMS
4. If you are using Laerdal LINK Technology Training Pads, use any Laerdal
manikin equipped with Laerdal LINK Technology, such as Laerdal AED
Resusci Anne or AED Little Anne. (The Laerdal LINK technology will
indicate correct placement of the pads on the manikin.)
5. If you are training in infant/child defibrillation, insert the training Infant/
Child Key in the port identified on the diagram on the inside front cover
of this manual. The infant/child mode is intended for training in
defibrillation of an infant or child under 8 years old or 55 lbs (25 kg).*
SELECTING A TRAINING SCENARIO
When you are ready to use the AED Trainer 3, follow the steps below:
1. Press and hold the green On/Off button for approximately six seconds.
The AED Trainer 3 will instruct you to press the orange Shock button to
select a training scenario.
* The training Infant/Child Key should be kept with the AED Trainer 3, but not
connected until you are ready to use the AED Trainer 3 in a pediatric scenario.
123
456

PHILIPS MEDICAL SYSTEMS
12
2. Press the orange Shock button as directed. The AED Trainer 3 announces
the current training scenario number.
3. To select a different scenario, press and hold the orange Shock button to
scroll through each of the eight scenarios in sequence. The AED Trainer 3
announces each scenario number as it is reached. See page 17 for a
detailed description of each scenario.
4. When you reach the desired scenario, press the On/Off button to turn
off the AED Trainer 3 and store the scenario selection on the Operating
System Card. The selected scenario will be active the next time the AED
Trainer 3 is turned on.
NOTE: The AED Trainer 3 automatically turns off if it is inactive for ten
minutes.
RUNNING A TRAINING SCENARIO
To run a training scenario, press the On/Off button to turn on the AED
Trainer 3, and following the AED Trainer 3’s voice instructions to simulate use
of the FR3 AED in an emergency. For troubleshooting assistance, see page 21.
USING THE OPTIONAL REMOTE
CONTROL
If desired, the AED Trainer 3 can be used with an
optional remote control that allows the instructor to
select and override training scenarios.
The remote control uses infrared light and requires a
direct or indirect light path from the remote control to
the receiver window on the AED Trainer 3.
Do not
cover the receiver window when using the remote
control
. The location of the receiver window is identified
on the diagram on the inside front cover of this manual.
NOTE: If a direct line is blocked, pointing the remote control at the ceiling
may provide a good indirect light path.
OK
1 2 3 4
5 6 7 8
AED Trainer 3

13
PHILIPS MEDICAL SYSTEMS
See page 19 for a description of the Remote Control operation.
NOTE: The AED Trainer 3 can be configured for use with the AED
Trainer 2 remote control, if desired. See page 6 for directions on changing
the configuration.

PHILIPS MEDICAL SYSTEMS
14
APPENDICES
PARAMETER SETTINGS
TRAINING SCENARIOS
REMOTE CONTROL
TROUBLESHOOTING TIPS
SPECIFICATIONS
REGULATORY INFORMATION
GLOSSARY OF SYMBOLS