Philips RI7035 User manual

RI7035

4

IMPORTANT
- Perform Calc-Clean process regularly for great steam and prolonged life (Fig. 1).
- Recommended water to use: distilled or demineralised water (Fig. 2).
IMPORTANTE
- Execute o processo Calc-Clean regularmente para garantir excelente qualidade de vapor e vida útil
prolongada (g. 1).
- Água recomendada para uso: destilada ou desmineralizada (g. 2).
CALC
CLEAN
1 2

RI7035
ENGLISH 6
PORTUGUÊS DO BRASIL 12

6
Introduction
Congratulations on your purchase and welcome to Philips! To fully benet from the support that
Philips offers, register your product at www.philips.com.br/clube.
This iron has been approved by The Woolmark Company Pty Ltd for the ironing of wool-only
products, provided that the garments are ironed according to the instructions on the garment label
and those issued by the manufacturer of this iron. R1401. In the United Kingdom, Eire, Hong Kong
and India, the Woolmark trademark is a certication trademark.
Important
Read this important information carefully before you use the appliance and save it for future
reference.
Danger
- Never immerse the appliance in water.
Warning
- Do not use the appliance if the plug, the mains cord, the supply hose or the appliance itself
shows visible damage, or if the appliance has been dropped or leaks. For repair or service, you
must have the appliance inspected by Philips, a service centre authorised by Philips or similarly
qualied persons.
- Check if the voltage indicated on the type plate corresponds to the local mains voltage before
you connect the appliance
- Do not immerse the iron or the steam generator in water.
- Do not leave the appliance unattended when it is connected to the mains.
- This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
- Children should be supervised to ensure that they do not play with the appliance.
- Keep the appliance and the mains cord out of the reach of children.
- Do not use any other cap on the steam generator than the EASY DECALC knob that has been
supplied with the appliance.
- Specic types only: Do not open and remove the EASY DE-CALC knob from the steam
generator during use.
- If steam or hot water droplets escape from under the EASY DE-CALC knob when the
appliance heats up, switch off the appliance and tighten the EASY DE-CALC knob. If steam
continues to escape when the appliance heats up, switch off the appliance and contact a service
centre authorised by Philips.
- Specic types only: The iron platform (stand) can become extremely hot, and may cause burns if
touched. Let it cool down for 5 minutes when performing cartridge replacement.
- CAUTION: Hot surface (Fig. 3)
Surfaces are liable to get hot during use (for irons with hot symbol marked on the appliance).
- Specic types only: Do not let the iron rest on its heel during the Calc-Clean process. Hot water
comes out of the iron together with steam.
Caution
- Only connect the appliance to an earthed wall socket.
- Fully unwind the mains cord before you put the plug in the wall socket.
- Always place and use the iron and the steam generator on a stable, level, horizontal and heat-
resistant surface.
- The iron platform and the soleplate of the iron can become extremely hot and may cause burns
if touched. If you want to move the steam generator, do not touch the iron platform.
ENGLISH

- When you have nished ironing, when you clean the appliance, when you ll or empty the
water tank and also when you leave the appliance even for a short while: put the iron back on
the iron platform, switch off the appliance and remove the mains plug from the wall socket.
- This appliance is intended for household use only.
Electromagnetic elds (EMF)
This Philips appliance complies with all applicable standards and regulations regarding exposure to
electromagnetic elds.
General description (Fig. 4)
1 Carry lock (specic types only)
2 Water tank lling funnel
3 Water tank
4 Iron platform
5 Water supply hose
6 Mains cord with plug
7 Calc-Clean button with Calc-Clean light
8 On/off button with power-on light
9 ECO button with light
10 Soleplate
11 Steam trigger
12 ’Iron ready’ light
13 Smart Calc-Clean container
OptimalTempTechnology
The OptimalTemp technology enables you to iron all types of ironable fabrics, without adjusting the
iron temperature.
- Fabrics with these symbols are ironable, for example linen, cotton, polyester, silk, wool, viscose
and rayon (Fig. 5).
- Fabrics with this symbol are not ironable.These fabrics include synthetic fabrics such as Spandex
or elastane, Spandex-mixed fabrics and polyolens (e.g. polypropylene), but also prints on
garments (Fig. 6).
Recommended water to use: distilled or demineralised water
Your appliance has been designed to be used with tap water. If you live in an area with hard water,
fast scale build-up may occur. It is therefore recommended to use distilled or demineralised water to
prolong the lifetime of your appliance.
Do not use perfumed water, water from the tumble dryer, vinegar, starch, descaling agents, ironing
aids, chemically descaled water or other chemicals, as they may cause water spitting, brown
staining or damage to your appliance.
Ironing
Please read the quick start guide on the packaging carefully to start using your
appliance.
Note: Keep the steam trigger pressed continuously when you move the iron over the fabric while you iron.
ENGLISH 7

IMPORTANT - Cleaning and maintenance
Smart Calc-Clean System
Your appliance has been designed with a Smart Calc-Clean system to ensure that descaling and
cleaning is done regularly.This helps to maintain a strong steam performance and avoids dirt and
stains coming out of the soleplate over time.To ensure that the cleaning process is performed, the
steam generator gives regular reminders. Besides that, a second defence step to protect the steam
generator from scale is integrated: the steam function gets disabled if descaling is not done after
1 hour steam ironing once the reminder came up.After descaling is done, the steam function will be
restored.This takes place regardless of the type of water used.
Sound and light Calc-Clean reminder
- After 1 to 3 months of use, the light of the Calc-Clean button starts ashing and the appliance
starts beeping to indicate that you have to perform the Calc-Clean process (Fig. 7).
- You can continue steam ironing for 1 hour while the Calc-Clean light ashes and the appliance
beeps.After 1 hour, the steam function is automatically disabled.You have to perform the
Calc-Clean process before you can continue steam ironing. (Fig. 8)
Performing the Calc-Clean process with the Calc-Clean container
Do not leave the appliance unattended during the Calc-Clean process.
Always perform the Calc-Clean process with the Calc-Clean container. Do not interrupt the
process by lifting the iron up from the Calc-Clean container, as hot water and steam will come
out of the soleplate.
1 Fill up the water tank halfway (Fig. 9)
Note: Make sure that the appliance is plugged in and switched ON during the Calc-Clean process.
2
Place the Calc-Clean container on the ironing board or any other even, stable surface (Fig. 10).
3 Place the iron stably on the Calc-Clean container (Fig 11).
4 Press and hold the CALC-CLEAN button for 2 seconds until you hear short beeps (Fig. 12)
Note:The Calc-Clean container has been designed to collect scale particles and hot water during the
Calc-Clean process. It is perfectly safe to rest the iron on this container during the entire process.
5 During the Calc-Clean process, you hear short beeps and a pumping sound (Fig.13).
6 Wait approximately 2 minutes for the appliance to complete process.When the Calc-Clean
process is completed, the iron stops beeping and the CALC-CLEAN light stops ashing (Fig. 14).
7 Wipe the iron with a piece of cloth (Fig. 15). Put the iron back on the base station.
Caution:The iron is hot.
8 As the Calc-Clean container becomes hot during the Calc-Clean process, wait approx.
5 minutes before you touch it.Then carry the Calc-Clean container to the sink, empty it and
store it for future use (Fig 16).
9 If necessary, you can repeat steps 1 to 8. Make sure that you empty the Calc-Clean container
before you start the Calc-Clean process.
Note: During the Calc-Clean process, clean water may come out of the soleplate if no scale has
accumulated inside the iron.This is normal.
For more information on how to carry out the Calc-Clean process, refer to the videos in this link:
http://www.philips.com/descaling-iron.
ENGLISH8

Energy saving
Eco mode
By using the ECO mode (reduced amount of steam), you can save energy without compromising
on the ironing result.
1 To activate the ECO mode, press the ECO button.The green ECO light goes on. (Fig. 17)
2 To deactivate the ECO mode, press the ECO button again.The green light goes off.
Safety auto-off (specic types only)
The safety auto-off function automatically switches off the appliance if it has not been used for
5 minutes, to save energy.
Recycling
Do not throw away the appliance with the normal household waste at the end of its life, but hand it
in at an ofcial collection point for recycling. By doing this, you help to preserve the environment.
Guarantee and support
If you need information or support, please visit www.philips.com.br/suporte or read the
separate worldwide guarantee leaet.
Troubleshooting
This chapter summarises the most common problems you could encounter with the appliance.
If you are unable to solve the problem with the information below, visit www.philips.com.br/
supporte for a list of frequently asked questions or contact the Consumer Care Centre in your
country.
Problem Possible cause Solution
The iron does not
produce any steam. There is not enough water in the water tank. Fill the water tank beyond the MIN indication. Press and hold the steam trigger
until steam comes out. It may take up to
30 seconds until steam comes out.
You have not pressed the
steam trigger. Press and hold the steam trigger until steam comes out.
The steam function has been
disabled until you have
performed the Calc-Clean
process.
Perform the calc-clean process to restore
the steam function (see chapter
‘IMPORTANT - Cleaning and
maintenance’).
The light of the
Calc-Clean button
ashes and/or the
appliance beeps.
This is the Calc-Clean
reminder. Perform the Calc-Clean process within 1 hour after the Calc-Clean reminder is
given (see chapter ‘IMPORTANT - Cleaning
and maintenance’).
ENGLISH 9

Problem Possible cause Solution
The light of the
Calc-Clean button
ashes and the
appliance beeps
every time I press
the steam trigger.
No steam comes
out of the
soleplate.
You have not done or have
not completed the Calc-Clean
process.
Perform the Calc-Clean process to enable
the steam function again (see chapter
‘IMPORTANT - Cleaning and
maintenance’).
The appliance has
switched off. The safety auto-off function was activated.This happens
automatically when the steam
generator has not been used
for more than 5 minutes.
Set the on/off switch to ‘off’ position and
then to ‘on’ position.
The appliance
produces a loud
pumping sound.
The water tank is empty. Fill the water tank with water and press the
steam trigger until the pumping sound
becomes softer and steam comes out of
the soleplate.
Water droplets
come out of the
soleplate.
After the Calc-Clean process,
remaining water may drip out
of the soleplate.
Wipe the soleplate dry with a piece of
cloth. If the light in the Calc-Clean button
still ashes and the appliance still beeps,
perform the Calc-Clean process (see
chapter ‘IMPORTANT - Cleaning and
maintenance’).
The Calc-Clean process has
not been completed. You have to perform the Calc-Clean process again (see chapter ‘IMPORTANT -
Cleaning and maintenance’).
Dirty water and
impurities come
out of the
soleplate.
Impurities or chemicals
present in the water have
deposited in the steam vents
and/or soleplate.
Perform the Calc-Clean process regularly
(see chapter ‘IMPORTANT - Cleaning and
maintenance’).
Water ushes out
of the soleplate. You have accidentally started the Calc-Clean process (see
chapter ‘IMPORTANT -
Cleaning and maintenance’).
Switch off the appliance.Then switch it
back on again. Let the iron heat up until the
‘iron ready’ light lights up steadily.
The Calc-Clean
process does not
start.
You have not pressed the
Calc-Clean button for 2
seconds until the appliance
started beeping.
See chapter ‘IMPORTANT - Cleaning and
maintenance’.
The iron leaves a
shine or an imprint
on the garment.
The surface to be ironed was
uneven, for instance because
you were ironing over a seam
or a fold in the garment.
Perfect Care is safe on all garments.
The shine or imprint is not permanent and
will disappear when you wash the garment.
Avoid ironing over seams or folds or you
can place a cotton cloth over the area to
be ironed to avoid imprints.
ENGLISH10