Philips LWL2 Series User manual

LWL2 Series
VANDAL-RESISTANT WET/DAMP LOCATION LED EXIT
Page 1 of 2
Job Information Type:
Job Name:
Cat. No.:
Notes:
Features
Illumination: Illumination
of the exit stencil face is
accomplished with long lasting,
high-output LEDs. Hot spots
and striations are eliminated
by the internal light chamber,
which is specially designed
around the high-performance
LED array. Average illumination
levels are in excess of 25fl
(79 cd/m2).
Housing: Die-cast aluminum
housing with premium impact-
resistant injection molded
polycarbonate covers. Housing
is powder coated and back
cover is molded in color to
match. Front cover is clear.
Stencil is provided with field
selectable chevrons and is
contained inside the fully
gasketed housing. All exposed
hardware is both vandal-
resistant and anti-corrosion
coated. Universal knockouts on
backplate allow wall mounting
directly to standard junction
boxes. Die-cast aluminum
canopy is provided for top/side
mounting and is powder coated
to match housing.
Operating Temperature
Range: Wet/Damp Location
-40°F (-40°C) to 113°F (45°C)
Diagnostic Electronics
(standard): 120/277 VAC
dual voltage input with surge
protection is standard on all
AC models. For emergency
operation, the charging system
is microprocessor driven with
software embedded diagnostic
routine and temperature
compensation. 120/277 VAC
input, surge protection,
brownout, AC lockout and low
voltage disconnect features are
standard.
Self-Testing Diagnostics
(standard): The diagnostic/
charging platform with self-
testing mode automatically
runs a one-minute self-test
every 30 days and a 30-minute
test on the sixth and twelfth
month. A one-minute or
90-minute test may be initiated
via the push to test switch on
the unit or by activating the
appropriate test command on
the optional IR test device.
Electrical Specifications:
AC Only Red:
3.8 W (120 VAC), PF 0.96
3.8 W (277 VAC), PF 0.91
AC Only Green:
4.0 W (120 VAC), PF 0.95
4.0 W (277 VAC), PF 0.90
Self-Powered Red:
4.7 W (120 VAC), PF 0.95
4.8 W (277 VAC), PF 0.97
Self-Powered Green:
4.7 W (120 VAC), PF 0.95
4.7 W (277 VAC), PF 0.99
Code Compliance
UL 924 and UL wet/damp
location listed. NFPA 101,
NEC, BOCA, OSHA and IBC
illumination standards. Meets
ADA specifications for wall
mounted lighting fixtures. IEC
61951-1 Life Testing (batteries).
Certified to the California
Energy Commission in
accordance with California law.
NEMA Premium certified.
Warranty
Five-year full electronics and
five-year full plus five-year
prorated battery warranty.
4.5"
(11.43 cm)
8.85"
(22.48 cm)
LWL2NURBSD2T
13.8"
(35.26 cm)
4.5"
(11.43 cm)
2.4"
(6.1 cm)

LWL2 Series
VANDAL-RESISTANT WET/DAMP LOCATION LED EXIT
Page 2 of 2
Philips Lightolier
e: [email protected]
t: [phone]
w: www.lightolier.com
LWL2 Series August 8, 2011
Specifications are subject to change without notice.
© Koninklijke Philips Electronics N.V., 2011.All rights reserved.
Job Information Type:
Ordering Information
Series
LWL2 = Wet/
Damp Location
LED Exit
Blank = AC Only
SD2T = Self-
Testing Diagnostic
Electronics
(required with
nickel cadmium
models)
Model Designator
Note
1) Some options may impact UL listing. Consult factory for specifics.
2) Must specify “PM” option for compatibility with pendant kit.
A= Audible Diagnostics
BF = Buzzer/Flasher (self-powered units only)
BZ = DC Buzzer
DC = 12-48 VDC Input (AC only models)
EX = Special Input Transformer (consult
factory)1
FA = 24 VDC Fire Alarm Interface
FL = Emergency Flasher (self-powered units
only)
PM = Pendant Mount Only (must order
pendant kit accessory)2
SW = Special Wording (consult factory)
2CKT1 = 120 VAC Two Circuit (AC only
models)
2CKT2 = 277 VAC Two Circuit (AC only
models)
Factory Installed Options
Accessories (order as a separate item)
SDREMOTE = Infrared Remote Test Device
T15TPTOOL = Tamperproof Tool
TPKITB = Pendant Kit, 12” Stem, Black
TPKITW = Pendant Kit, 12” Stem, White
A= AC Only
N= Nickel
Cadmium
Battery Type
W= White Housing and White
Stencil
B= Black Housing and Black
Stencil
G= Gray Housing and Gray
Stencil
WA = White Housing and
Brushed Aluminum Stencil
BA = Black Housing and Brushed
Aluminum Stencil
GA = Gray Housing and Brushed
Aluminum Stencil
Stencil Face/Housing Color
LWL2
1= Single
U= Universal
Single/Double
Face
Face Options
R= Red
G= Green
Letter Color
8.85"
(22.48 cm)
13.8"
(35.26 cm)
5.5"
(13.97 cm)
2.4"
(6.1 cm)
Pendant Kit