Philips ED231 User manual

5"
7
3
/ 4 "
Ceramalux®High Pressure Sodium Non-Cycling
100 Watt ED231⁄2(Clear) Lamp
Featuring ALTO®Lamp Technology
wOrdering Information
Ordering Code C100S54/ALTO NC HPS 12PK
ANSI Designation S54
Product Number 14740-5
Description High Pressure Sodium
TCLP* Compliant
Non-Cycling
Package Quantity 12
wPhysical Characteristics
Bulb Size ED 231⁄2
Bulb Finish Clear
Base Mogul Screw
Maximum Overall Length (MOL) 73⁄4'' (197mm)
Light Center Length (LCL) 5'' (127mm)
Arc Length 1.3'' (33.4mm)
Arc Tube Length 2.24'' (57mm)
Arc Tube Material Aluminum Oxide
Max. Permissible Bulb Temp. 400°C (752°F)
Max. Permissible Base Temp. 210°C(410°F)
Max. Bulb to Base Eccentricity 3°
Max.Arc Tube to Base Eccentricity 3°
wOperating Characteristics (Photometric)
Approx. Initial Lumens110,000
Approx. Mean Lumens29000
Rated Average Life, Hours430,000
Correlated Color Temperature (CCT)3, 5 2100 K
CIE Chromaticity Approximate3x-.520, y-.420
Color Rendering Index (CRI) 18
Efficacy (lpw) 100
wOperating Position
Universal
wTCLP*Characteristics
T
oxicity Characteristic Leaching Procedure(US EPA TCLP) Results
Hg Pb
EPA Limit (mg/l) max 0.200 5.00
C100S54/ALTO NC HPS 0.087 <0.11
Mercury (mg/lamps) max 3.4

Lamp Watts (Nominal) . . . . . . . . . . . . . . . . . . . . . . . . . . 100
Lamp Operating Voltage (rms) (Nominal)3...........65
Initial Lamp Voltage Range (rms)6..................57–73
Lamp Operating Current (Amps) (rms) (Nominal). . . . 2.1
Maximum Lamp Starting Current (Amps) (rms) . . . . . . 3.2
Lamp Current Crest Factor (Maximum) . . . . . . . . . . . . 1.8
Warm-up Time to 80% of Output . . . . . . . . . . . . . . . . . 5 Minutes
Restrike Time for Hot Lamp. . . . . . . . . . . . . . . . . . . . . . 5 Minutes
Ballast Type . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ANSI S54
Ballast Open Circuit Voltage (Minimum) . . . . . . . . . . . . 110
Pulse Peak Volts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2500 Min., 4000 Max.
Pulse Width @ 90% Peak . . . . . . . . . . . . . . . . . . . . . . . . 1 Micro Second Minimum
Pulse Frequency (Minimum)
Lag Ballast ....................................1per Cycle
Lead Circuit Ballast . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 per Half Cycle
Minimum Operating Temperature. . . . . . . . . . . . . . . . . . -30°C
Reference Ballast Impedance . . . . . . . . . . . . . . . . . . . . . 44 Ohms at 120V RIV
Maximum Lamp Watts . . . . . . . . . . . . . . . . . . . . . . . . . . 124
Minimum Lamp Watts . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
Maximum Voltage Increase by Fixture . . . . . . . . . . . . . . 4
Featuring ALTO®Lamp Technology
Ceramalux®High Pressure Sodium Non-Cycling 100 Watt ED231⁄2(Clear) Lamp
Philips Lighting Company
200 Franklin Square Drive
P.O. Box 6800
Somerset, NJ 08875-6800
1-800-555-0050
ADivision of Philips Electronics North America Corporation
Updated 09/05 TDS-147405
Philips Lighting
281 Hillmount Road
Markham, Ontario
Canada L6C 2S3
1-800-555-0050
ADivision of Philips Electronics Ltd.
www.philips.com
100
90
80
70
60
00%
Percent of Rated Average Life
4
Percent – Approx. Initial Lumens
20 40 60 80 100
Approximate Lumen Maintenance Curve
for ALTO NC HPS Lamps:
100
90
80
70
60
50
00%
Percent of Rated Average Life
4
Percent – Approx. Initial Lumens
20 40 60 80 100
Approximate Survival Curve
for ALTO NC HPS Lamps:
Footnotes:
1) Measured at 100 hrs. life. Approximate lumen values listed are for vertical or horizontal operation of lamp.
2) Approximate mean lumen output at 40% of lamp rated average life.
3) Measured at rated lamp watts on a linear reactor. LPW does not include ballast losses.
4) Rated average life is the life obtained, on the average, from large representative groups of lamps in laboratory tests under controlled conditions at 10 or more operating hours per star t.
It is based on survival of 65% of the lamps and allows for individual lamps or groups of lamps to vary considerably from the average.
5) Approximate color temperature in Kelvin degrees.
6) Measured with the lamp operating at rated watts. Measured lamp voltage will change as the ballast changes lamp wattage.
*The TCLP is the US EPA’s Toxicity Characteristic Leaching Procedure
WARNINGS, CAUTIONS AND OPERATING
INSTRUCTIONS for Ceramalux High Pressure
Sodium Lamps
R
“WARNING: These lamps must be operated
in fixtures designed for use with High Pressure
Sodium lamps.The fixture wattage rating must match
the wattage indicated on the outer glass bulb. Do not
scratch the outer bulb or subject it to pressure as this
could cause the outer bulb to crack or shatter. A partial
vacuum in the outer bulb may cause glass to fly if the glass
is struck. Operating the lamp improperly may result in
PERSONAL INJURY, PROPERTY DAMAGE,
BURNS AND FIRE.
1) If the outer glass bulb is broken, shut off power
immediatelyand removethe lamp after it has cooled.
2) Use only auxiliary equipment meeting Philips
and/or ANSI standards. Use within voltage limits
recommended by ballast manufacturer.
A. Operate lamp only within specified limits
of operation.
B. For total supply load refer to ballast manufacturers
electrical data.
3) Protect lamp base, socket and wiring against moisture,
corrosiveatmospheres and excessiveheat.
4) Replace the lamp if the outer glass bulb has been
scratched, cracked or damaged in any way.
5) If a lamp bulb support is used, be sure to insulate
the supportelectricallyso as to avoid possible
decomposition of the bulb glass.
6) Do not use this lamp in a fixture which redirects a
substantial portion of the energy toward the arc tube
and its immediate vicinity, as this may lead to very early
lamp failure.
7) Take care in handling and disposing of lamps. If arc tube
is broken, avoid skin contact with any of the contents
or fragments.
8) The arc tube of this lamp contains sodium and
mercury. Dispose of in accordance with federal,
state and local requirements.