Philips TrueLine SM530C User manual

SM530C
TrueLine End cap
4A
MAX.
T2 5
220 V
240 V
indoor
50Hz
60Hz
IP20
IK02
GLO W
WIRE
650 °C
Max.
35 °C
Min.
10 °C
Printed in Hungary
Data subject to change without notice
Keep for future reference: www.lighting.philips.com
Surface
Mounted A B C D E
Sensor/
Blind sensor
holder.
kg
Standalone ·
·
Line End ·
·
Line Feature ·
·
A
B D
88
14
93
55
StandAlone
R 7.5
28
Surface Mounted
88 93
55 A
BC D
Line End
A
B
Line Feature
C
D
D*
D* = D of previous Luminaire
Line End / Line Feature
E (D*+B )
13
79
50
39
Dimensions in mm
444316024221
© 2020, Signify Holding. All rights reserved.
Lorem ipsum
1/8

2/8
Cover remover (ZZS400 OCR)
Replace 9a, b, c,
1
2a 2b 2c
1
1
Not
included
2
3
!
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
6mm
DALI
Standalone /
Line End
ACL/MDU
versions only
L
N
+ DA / LS
DA
Black
Yellow-Green
Blue
Orange
Purple
PSD / SRD
PoE
Line end
Line Feature 1
Line Feature 2,
(every 11. piece in a line
with extra cabel)
1
Line End Line Feature Line Feature
1
2 2
!
...
2x 3x 4x ... ...
2x 3x 4x ... ... ... 10x Max.
2x 3x 4x ... ... ... ......
1x
1x 11x
1x
10x Max.

8c
Push-in (PIP) SRD
PI-3
Line End / Line Feature
3
N
DALI 1
L
N
Brown
Yellow-Green
Blue
DALI 1
DALI 1
EMPTY SLOTS
8a
8b
Push-in (PIP) PSD
PI-5
Line End / Line Feature
PSD
PI-7
Line End / Line Feature
3
N
1
2
DALI 1
L
N
+ DA / LS
DA
Black
Yellow-Green
Blue
Brown
Grey
+ DA / LS
DA
Brown
Blue
DALI 1
DALI 1
DALI 2
DALI 2
3
N
1
2
DALI 1
L
N
+ DA / LS
DA
Black
Yellow-Green
Blue
Brown
Grey
DALI 2
DALI 1
DALI 1
! !
as ymmetric
LightEngine
9b9a
9c
9d
CLICK
1 mm 1 mm
LightEngine
2 mm 2 mm
Po E
Condition Philips to specify to
the customers (instruction):
> to use UTP (Unshielded Twisted
Pair) CAT5E or CAT6 cable.
> the maximum length of the cable
to be 20 meters.
Apply a minimum radius of the
Ethernet cable of 4x the cable
diameter.
LightEngine LightEngine
3/8

4/8
Push and twist screwdriver in designated slot
to click out the bracket, including the sensor
1
Once unlocked, take out
sensor from the front
2
POE
Sensor wires
RJ10 Cable +
Coupler
SRD
Connect the new sensor to
the wires and put it into the
designated slot, click the bracket in
3a
If you use a blind cap instead of a sensor,
insert the cable into the blind cap
3b
POE
Make sure to isolate
the bare ends of the cable,
each core wire separately.
SRD
Sensor wires
RJ10 Cable
Polarisation
not critical
POE
SRD
Blind cap Sensor
Sensor upgrade procedure
3 4b4a
4
1
23
5
T2 5
T2 5
T2 5
Line End Line Feature Line Feature

I mains (A)
I nom.
Time (us)
Tref
max/2
I max
Inrush current
5/8
LASER RADIATION
AVOID DIRECT EYE EXPOSURE
CLASS 2M LASER PRODUCT
210J/M2/10S 443.533.552nm
wg PN-EN 60825-1 -2005
!Given the choices made in this unique lighting concept, there are a few instructions regarding the maintenance.
• Prevent water from entering on or in the luminaire at installation and during use of the luminaire
• During installation or maintaining the luminaire please use gloves to avoid spots on the cover.
• Do not clean with a dry cloth as it will cause the product to attract dust. Dirty spots can be removed:
Only dust: use a damped cloth (no dripping water), preferably anti-static.
Fingerprints etc: use a damped cloth (no dripping water) with a cleaner
approriate for polycarbonate/PMMA plastics
• Do not touch electronic components as they are ESD sensitive.
• Do not stare into LED beam.
• Luminaire should not be used for illumination during building activities.
due to dust accumulation inside the luminaire.
• Please do not remove the protect lm before installing to avoid scraping or dirtying the optical part.
©2020 Signify Holding
All rights reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation or contract, is believed to be accurate and
reliable and may be changed without notice. No liability will be accepted by the publisher for any consequence of its use.
Publication thereof does not convey nor imply any license under patent- or other industrial or intellectual property rights.
Signify Holding
The Netherlands
!
The light source contained in this luminaire
shall only be replaced by the manufacturer or
his service agent or a similar qualied person.
PSD SRD
13
21
280
17
21
26
33
22
28
36
44
55
Electrical
characteristics
Imax (A) 21
Tref (µs) 280
MCB Luminaire max.
B-10 A 15
B-13 A 19
B-16 A 24
B-20 A 30
B-25 A 37
C-10 A 25
C-13 A 32
C-16 A 41
C-20 A 50
C-25 A 62