Philips SELECON PL1IRR User manual

The material in this manual is for information purposes only and is subject to change without notice. Philips
Selecon assumes no responsibility for any errors or omissions which may appear in this manual. For comments and
suggestions regarding corrections and/or updates to this manual, please visit the Philips Selecon web site at
www.seleconlight.com or contact your nearest Philips Selecon office.
El contenido de este manual es solamente para información y está sujeto a cambios sin previo aviso. Philips
Selecon no asume responsabilidad por errores o omisiones que puedan aparecer. Cualquier comentario, sugerencia
o corrección con respecto a este manual, favor de dirijirlo a la oficina de Philips Selecon más cercana.
Der Inhalt dieses Handbuches ist nur für Informationszwecke gedacht, Aenderungen sind vorbehalten. Philips
Selecon uebernimmt keine Verantwortung für Fehler oder Irrtuemer, die in diesem Handbuch auftreten. Für
Bemerkungen und Verbesserungsvorschlaege oder Vorschlaege in Bezug auf Korrekturen und/oder
Aktualisierungen in diesem Handbuch, moechten wir Sie bitten, Kontakt mit der naechsten Philips Selecon-
Niederlassung aufzunehmen.
Le matériel décrit dans ce manuel est pour information seulement et est sujet à changements sans préavis. La
compagnie Philips Selecon n'assume aucune responsibilité sur toute erreur ou ommission inscrite dans ce manuel.
Pour tous commentaires ou suggestions concernant des corrections et/ou les mises à jour de ce manuel, veuillez s'il
vous plait contacter le bureau de Philips Selecon le plus proche.
Note: Information contained in this document may not be duplicated in full or in part by any person without prior written
approval of Philips Selecon. Its sole purpose is to provide the user with conceptual information on the equipment mentioned. The
use of this document for all other purposes is specifically prohibited.
Document Number: 02.9692.0002
Version as of: 05 August 2010 (PL1IRR)
PL1IRR Remote Control User’s Guide
©2010 Philips Group. All rights reserved.
Philips Selecon - Dallas
10911 Petal Street
Dallas, TX 75238
Tel: [phone]
Fax: [phone]
Philips Selecon - Auckland
19-21 Kawana Street
Northcote, Auckland 0627
New Zealand
Tel: [phone]
Fax: [phone]
Philips Selecon - New York
267 5th Ave, 4th Floor
New York, NY 10016
Tel: [phone]
Fax: [phone]
Philips Selecon - Europe
Marssteden 152
Enschede 7547 TD
The Netherlands
Tel: [phone]
Fax: [phone]
Philips Selecon - Asia Limited
Room 6-10, 20/F Delta House 3 On Yiu Street
Shatin, N.T. Hong Kong
Tel: + 852 2757 3033
Fax: + 852 2757 1767
Website:
www.seleconlight.com

1
PL1IRR Remote Control User’s Guide
IMPORTANT INFORMATION
Warnings and Notices
Philips Selecon Limited Three-Year Warranty
Philips Selecon offers a three-year limited warranty of its products against defects in materials or workmanship
from the date of delivery. A copy of Philips Selecon three-year limited warranty containing specific terms and
conditions can be obtained from the Philips Selecon web site at www.seleconlight.com or by contacting your local
Philips Selecon office.
When using electrical equipment, basic safety precautions should always be followed including the following:
a. READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
b. Do not use outdoors.
c. Do not use near gas or electric heaters.
d. The use of accessory equipment not recommended by the manufacturer may cause an unsafe
condition.
e. Do not use this equipment for other than intended use.
f. Refer service to qualified personnel.
SAVE THESE INSTRUCTIONS.
WARNING: You must have access to a main circuit breaker or other power disconnect device
before installing any wiring. Be sure that power is disconnected by removing fuses or turning the
main circuit breaker off before installation. Installing the device with power on may expose you to
dangerous voltages and damage the device. A qualified electrician must perform this installation.
WARNING: Refer to National Electrical Code® and local codes for proper use specifications.
WARNING: This equipment is intended for use in accordance with the National Electric Code® and
local regulations. It is also intended for installation in indoor applications only. Before any electrical
work is performed, disconnect power at the circuit breaker or remove the fuse to avoid shock or
damage to the control. It is recommended that a qualified electrician perform this installation.
WARNING: The PL1IRR Remote Control contains a Class 2 laser. Do not look directly into laser
beam or damage to eye may result. Handle with caution.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASER DIODE
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW

User’s Guide PL1IRR Remote Control
2TABLE OF CONTENTS
TABLE OF CONTENTS
IMPORTANT INFORMATION
Warnings and Notices...................................................................................................................................... 1
Philips Selecon Limited Three-Year Warranty............................................................................................... 1
TABLE OF CONTENTS
PREFACE
About this Guide.............................................................................................................................................. 3
Product Description......................................................................................................................................... 3
Before Using the Infrared Remote .................................................................................................................. 3
PL1IRR PROGRAMMING REMOTE OVERVIEW
Infrared Remote Control Features................................................................................................................... 4
OPERATION AND PROGRAMMING
Using the PL1IRR Infrared Remote Control .................................................................................................. 5
Troubleshooting............................................................................................................................................... 5

3
PL1IRR Remote Control User’s Guide
PREFACE
About this Guide
The document provides installation and operation instructions for the following product:
• PL1IRR Remote Control (includes two AAA batteries and user’s guide)
Please read all instructions before using this product. Retain this manual for future reference. Additional information
for PL1 LED Luminaires including product descriptions may be downloaded at www.seleconlight.com
Product Description
The PL1IRR Remote Control is used to remotely program and control presets (1 through 6 and Off) of PL1 LED
luminaires (IR-enabled models only) over an unobstructed range of approximately 100 feet. IR-enabled PL1 LED
Luminaires have an integrated infrared (IR) receiver that allows them to receive IR commands from the PL1IRR
Remote Control. Using the Remote, colors (full color mixing)/presets/intensity can be programmed/selected, raised
and lowered, and fixtures may be turned On and Off.
Before Using the Infrared Remote
Install two AAA batteries (included) before operation. Refer to Figure 1 for more information.
Figure 1: PL1IRR Remote Battery Installation
PL1IRR Remote
Battery Compartment
Access Panel
AAA Battery (2 each -
supplied with remote)
+
_
To install two AAA batteries (included)
in PL1IRR remote:
Step 1. At rear of remote, remove battery
access panel by sliding it as
indicated.
Step 2. Note orientation of batteries as
indicated in battery compartment
of remote.
Step 3. Install batteries.
Step 4. Reinstall battery access panel.
Step 5. Remote is ready for use.
WARNING! PL1IRR Remote contains a
Class 2 laser. Do not stare or look directly
into laser beam.
+
_
Slide battery access panel away
from remote to install batteries.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASER DIODE
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW

User’s Guide PL1IRR Remote Control
4PL1IRR PROGRAMMING REMOTE OVERVIEW
PL1IRR PROGRAMMING REMOTE OVERVIEW
Infrared Remote Control Features
Figure 2: PL1IRR Programming Remote
LEARN
EXIT
1
LASER
COLOR
PRESETS
ENTER
PROGRAM
CANCEL
RED GREEN BLUE WHITE
SSSS
TTTT
WHITE
23
456
OFF
WARM COOL DAY
INTENSITY
PL1IRR
Intensity Raise/Lower -
Press top button to raise intensity and
bottom button to lower it. Tap the up
for 2% increase or tap down for a 1%
decrease. Press and hold (top or
bottom button) for sequential raise/
lower.
Preset (White Color Temperature) -
Allows selection of Warm, Cool or Day
color temperatures.
Note, only intensities may be stored
on White Color Temperature presets.
These presets cannot be edited or
changed
Presets (6 Levels or Off) -
Allows selection and programming of
one of six Presets (1 through 6) or
Preset Off.
Note, Off cannot be edited or changed.
Individual LED Color Adjustment -
Allows the raising or lowering of
individual LED colors. Press top
button to change color and bottom
button to lower it. Tap the up for 2%
increase or tap down for a 1%
decrease. Press and hold (top or
bottom button) for sequential raise/
lower.
Program -
Enter - After the luminaire to be
programmed is selected (by Laser),
press Enter to set the luminaire to
programming mode.
Laser (Luminaire Selector) - Press
Laser to select individual luminaire for
programming / adjustment.
Exit - Press to exit programming mode.
PL1IRR LED (indicator) -
The LED indicator will flash each time
a button is pressed.
WARNING! THIS DEVICE IS A CLASS 2 LASER. DO
NOT STARE OR LOOK DIRECTLY INTO BEAM.
Cancel -
Cancels the learn features (any
programming made will not be
recorded) RGBW will not be changed.
Learn -
After adjustments are made, the Learn
button (in conjunction with a preset
button) stores the new settings to a
specific preset if desired.
Laser / IR Window -
Laser and IR programming emits from
this end.
LASER RADIATION
DO NOT STARE INTO BEAM
CLASS 2 LASER PRODUCT
LASER DIODE
WAVELENGTH: 630 - 680 nm
MAX OUTPUT: <5 mW

5
PL1IRR Remote Control User’s Guide
OPERATION AND PROGRAMMING
Using the PL1IRR Infrared Remote Control
To select and program PL1 LED luminaire with PL1IRR remote:
Note: The IR, on the PL1 LED luminaire, must be set to "Enabled" in order for the PL1IRR remote to communicate
and control the fixture. Refer to PL1 LED Luminaire Installation & User’s Manual on luminaire menu settings.
Step 1. Point PL1IRR programming remote
Laser / IR window directly at luminaire
IR programming window (as shown in
Figure 2) and hit "Enter" button. Note,
each luminaire to be programmed/
adjusted needs to be selected and
programmed/adjusted individually.
Step 2. Point PL1IRR remote directly at
luminaire IR window and hit "Laser"
button. Luminaire to be programmed or
adjusted is now selected.
Note: At luminaire IR port, a Blue LED will
illuminate when the fixture is in programming
mode and blink Red when buttons are pressed on
IR remote to confirm it sees the remote and is
receiving commands.
Step 3. Set luminaire to preset or make
adjustments as desired.
Step 4. To save settings, hit "Learn" button and
then hit any Preset button (except Off -
Off cannot be programmed). Preset is
now saved. To cancel programming, hit "Cancel" button.
Step 5. After programming or adjustments are complete, hit "Exit" button. Repeat, as desired, on additional
luminaires to be programmed/adjusted.
Note: Refer to PL1 LED Luminaire Installation & User’s Manual for additional information. This manual is
available on the Philips Selecon web site at www.seleconlight.com.
Troubleshooting
Description Symptom Possible Cause/Remedy
IR remote programming. Fixture will not respond to IR
remote programming unit.
Luminaire not selected by laser...
Reselect luminaire by repeating luminaire selection step.
Not seeing IR remote control...
Make sure batteries are good in remote. Try fresh, fully charged
batteries.
Make sure IR is enabled in the fixture menu.
Insure IR remote is pointing at IR window in luminaire and that there
is nothing in between IR remote and luminaire IR window.
Clean luminaire IR window.
LEARN
EXIT
1
LASER
COLOR
PRESETS
ENTER
PROGRAM
CANCEL
RED GREEN BLUE WHITE
SSSS
TTTT
WHITE
23
456
OFF
WARM COOL DAY
INTENSITY
PL1IRR
PL1 LED Luminaire
(IR-enabled model)
PL1IRR Remote Control
PL1 IR
Port
Figure 3: PL1 LED Luminaire Programming / Control