Philips EM120B Series User manual

EM120B
Emergency
downlight
Battery
Round lens.
(Oval lens is
mounted).
Converter
indoor
50Hz
60Hz
220V
240V
IP20
LEDs
Max.
40 °C
Min.
0 °C
P1
GLOW
WIRE
650 °C
25
33
2
4.5
Ø80
Ø66
197
Dimensions in mm
Battery
Driver
I mains (A)
I nom.
Time (us)
Tref
max/2
I max
1 - 25
Inrush current
The luminaire shall be installed by a qualied elec-
trician and wired in accordance with the latest IEE
electrical regulations or the national requirements.
The light source of this luminaire is not replaceable;
when the light source reaches its end of life
the whole luminaire shall be replaced.
Clean with dry cloth.
Philips Lighting warranty is applicable only if the
indicated drivers are used.
-
-
-
-
ATTENTION
OBSERVE PRECAUTIONS
FOR HANDLING
ELECTROSTATIC
SENSITIVE
DEVICES
!
/
  
© / , Philips Lighting Holding B.V. All rights reserved
Printed in China
Data subject to change without notice
Keep for future reference: www.lighting.philips.com
Test CCT (K)
Lumen
(lm) P (W)
Ø mm
kg
EMB MT manual      
EMB AT auto
Electrical
characteristics
Inom (mA) 113
Imax (A) 48
Tref (µs) 1.2
MCB Downlights
Max.
B-10 A
B-13 A
B-16 A
C-10 A
C-13 A
C-16 A

The luminaire shall, under no circumstance,
be covered with thermal insulation matting or
similar material.
!
1
2
3 4
65
Ø 68 - 72
200
500
1000
500
Ø 6-9 mm
2 x 0.50-1.5 mm2
9
20
CLICK
CLICK
2
1
2
1
0.5Nm
P1
2
2
!
1
2
11
/

/
1
2
3
4
1
2 3
Replacement battery (lifetime 4 years)
1
Disconnect
Replace 3, 2, 1
Replacement lens
4
4
Beam angle 138°
-90°
0°
-30°
-60°
90°
30°
60°
Round lens for open area application.
Beam angle C0: 150° C90: 70°
-90°
0°
-30°
-60°
90°
30°
60°
Oval lens for pathway application.
1
1
2
2
2
2
2
1
P1
Compliant EUROPE standard EN1838 illminance requirement:
Escape route up to 2 m wide, 1 lx on the central axis and 0.5 lx
at 50% of the width.
Mounting height (m) Spacing distance (m)
2.5 16
3.0 18
3.5 20
Compliant EUROPE standard EN1838 illminance requirement:
Escape route up to 2 m wide, 1 lx on the central axis and 0.5 lx
at 50% of the width.
Mounting height (m) Spacing distance (m)
2.5 8
3.0 9
3.5 10

!
12
11
10
9
8
765
4
3
2
112
11
10
9
8
765
4
3
2
1
24h00
Indicator LED
Test button
Self test version
Once the unit is powered up it will automatically initiate a self test and diagnostics as follows:
Every 4 seconds : Checks for battery disconnection, charger board fault, lamp failure and transformerfailure
Every month : Performs a 3 minute duration test
Every year : Performs a 1 Hour or 3 Hour duration test
Dual color indicator LED:
Green solid on; Ready / normal operation
Green ashing; Testing
Red ashing; Requires service
Note 1: After repairing a service fault, press and hold the test button for 2 seconds to reset
Note 2: Manual testing also works with the self test unit
Manual test version
Charge time
/
Press test button once 30 second duration test
Press test button 2 times within 2 seconds 3 minute duration test
Press test button 3 times within 2 seconds 30 minute duration test
Press test button 4 times within 2 seconds 3 hours duration test
*One ash, 4 seconds pause Battery not connected
** Two ashes, 4 seconds pause Battery short or low battery voltage
*** Three ashes, 4 seconds pause Charger board fault
**** Four ashes, 4 seconds pause Transformer board fault
***** Five ashes, 4 seconds pause LED lamp fault