Philips City Line FC8434 User manual

ServiceManual
Philips Domestic Appliances and Personal Care
Published by Philips Domestic Appliances and Personal Care Printed in the Netherlands © Copyright reserved Subject to modification
City Line Melbourne Vacuum cleaner
FC8434
06/07
PRODUCT INFORMATION
- Colour: Cherry Red
- Electronically controlled motor speed
- Built-in cord winder
- Dustbag-full indicator in dust cover
- This product meets the requirements regarding
interference suppression on radio and TV.
- After the product has been repaired, it should function
properly and has to meet the safety requirements as
officially laid down at this moment.
TECHNICAL INFORMATION
- Maximum air displacement : 36 l/sec.
- Maximum vacuum water column : 270 cm
- Power consumption (IEC) : 1600 W
- Dust storage capacity : 2 l
- Cord length (depends on version) : 6 m
- Filter system : 5 filters
- Dimensions of cleaner : 382 x 292 x 218 mm
- Dimensions of packaging : 510 x 305 x 330 mm
- Net weight : 4.5 Kg
- Gross weight : 8,0 Kg
- Noise : 80 dB
OPTIONAL (accessories)
- FC8021 S-paper dustbags 8838 021 00000
- FC8032 Exhaust AFS micro filter 4822 015 70056
- HR6997 Sydney cotton dustbag 8836 997 01010
DISASSEMBLY- AND RE-ASSEMBLY ADVISE
- First lift and remove the knob and printed knob base and
then loosen mounting screws A.
AA
A
- Lift the motor housing (item 26) out of the lower housing
and take out the cord winder unit.
- To disassemble the cord winder, use TORX screwdriver no.
T10, which is one of a set consisting of T20; T15; T10;
T9; T8; T7 and T6 (code number 4822 395 50145).

FC8434
2-6
REPAIR INSTRUCTION
- The spare parts have been standardized as much as possible.
- Cotton dustbags are used in countries where paper dustbags
are unobtainable.
- If the reel half spring unit is replaced, shaft Fmust be
lubricated with silicone grease. Do not apply any silicone
grease to or spill any grease on terminals (36) or conductors
(35).
- Item 34 is provided with a long cord-winder spring, but
both long and short cords can be used in combination with
this spring. (L = 9.3 m)
- Depending on the length of the original cord, the spare
cord may have to be shortened.
- The cord winder spring must be tensioned to the maximum
level and then be rewound approx. 1.5 turn
- The RPM can be adjusted by means of the potentiometer
mounted on the PCB (item 25). The RPM is correctly
adjusted if the motor starts automatically and continues to
run smoothly with the ON/OFF position and the
adjustable potentiometer in minimum position.
- If the function of the electronic control unit (item 25) is
not required, the Triac must be short-circuited in the
manner shown in the circuit diagram.
- When the vacuum cleaner is used to suck up fine dust, the
pores of the dustbag may become clogged, causing the
passage of air through the dustbag to become obstructed.
As a result, the dustbag-full indicator will indicate that the
dustbag needs to be replaced, even though the dustbag is
not full at all.
ELECTRICAL DIAGRAM
M
MOTOR
POWER
MODULE
Brown
Blue
CORD WINDER
Black
Black
Triac
Short-circuit

FC8434
3-6
PARTS LIST
Pos Service code Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
21a
22
23
24
25
26
27
4322 005 18400
4341 009 01000
8838 021 00000
4822 480 10115
4341 009 00760
4341 001 70180
4322 005 18240
4341 001 70190
4322 003 26370
4322 003 26350
4322 003 12220
4822 480 40234
4322 005 18250
4341 009 00780
4341 005 00780
4322 005 18680
4322 003 26390
4322 003 26380
4322 003 26430
4322 003 26400
4822 015 70056
Not available*
4322 003 26810
4341 003 02330
4341 003 02390
4322 006 50600
4322 006 23170
4341 006 20570
4322 003 26420
4341 001 70210
Handle Cherry Red
Dustcover Cherry Red
S-bag set
Cotton dustbag (opt.)
Dustbag frame
Dust cover sealing
Lower housing sel. grey
Inlet rubber
Nose piece sel. grey
Rear Wheel sel. grey
Wheel bush
Safety filter
Caster assy sel. grey
Cover and filter
Turn knob grip stand (opt.)
Knob base pr.
Cord outlet sel. grey
Upper housing sel. grey
Pedal grey/blue
Back grille sel. grey
AFS filter
Wheel peg
Wheel bush lim. space
Cooling tube
Switch lever
Switch soldered
PCB 220 - 240 V
PCB 120 V
Motor cap sel. grey
Buffer back
* The wheel peg has been changed to a wheel bush (21a)
WK542 onwards.
Pos Service code Description
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
47
48
49
50
51
52
53
4322 009 06430
4322 009 06770
4822 466 62655
4341 003 02360
4322 003 06620
4322 001 72360
4322 009 07640
4322 009 07610
4322 009 09060
4341 005 01330
4341 005 00790
4322 006 01770
4341 006 01890
4322 006 02100
4322 006 02060
4322 006 02080
4341 003 01960
4341 004 20520
4322 007 31640
4322 004 23280
4341 003 02470
4341 003 01900
4322 004 22560
4322 007 45550
4322 001 99120
4322 004 22490
Motor ANS 1451 230 V
Motor ANS 1241 EL 120 V
Buffer ring front
ANS motor disc
Push rod
Brake tyre
Base plate assy
Reel half spring unit
Reel half spring unit PRC
Reel half contact side
Contact plate assy
Flat cord set Japan/Taiwan 5.3 m
Cordset 1.0 / 5.3 m PRC / R
Flat cord set U.K./H.K. 6.3 m
Flat cord set Euro/Korea 6.3 m
Flat cord set Swiss
Bend
Bend and hose
Leaf Spring
Telescopic tube stand.
Accessory clip
Crevice nozzle stand.
Small nozzle stand.
Tube spring
Tube bush
Reach & Clean Nozzle stand.

FC8434
4-6
EXPLODED VIEW
A
D
A
A
B
D
C
C
B
14
15
16
17
18
19
20
9
13
3
1
7
8
2
4
5
6
911
10
21
21a
12

FC8434
5-6
EXPLODED VIEW
E
E
E
E
31
32
33
34
36
37÷40
26
28
29
30
35
27
25
23
24
22
FG
G

FC8434
6-6
EXPLODED VIEW
42
41
Taiwan / P.R.C. 37 Korea / Europe 39
Swiss 4038H.K. / U.K.
52
51
47
48
49
50
43
53