Philips HR6072/10 User manual

Jack HR6073,6072

ENGLISH 6
POLSKI 15
ROMÂNĂ 25
РУССКИЙ 34
ČESKY 45
MAGYAR 54
SLOVENSKY 63
УКРАЇНСЬКА 72
HRVATSKI 83
EESTI 92
LATVISKI 101
LIETUVIŠKAI 110
SLOVENŠČINA 118
HR6073,HR6072
5

Important
◗Read these instructions for use carefully and
look at the illustrations before you start using
the appliance.
◗Always switch the vacuum cleaner off after
use.
◗Never suck up ashes until they are cold.
◗Do not suck up flammable or corrosive
liquids.
◗Do not let water enter the vacuum cleaner or
the wall holder.Never immerse the vacuum
cleaner or the wall holder in water.
◗The charger plug feels warm.This is normal.
◗Only charge the vacuum cleaner with the
charger supplied.
◗Do not hold the appliance with the nozzle
pointing upwards and do not tilt the appliance
to one side when sucking up liquids.
◗Do not use the appliance if it is damaged.Take
it to an authorised Philips service centre for
repair.
Preparing the appliance for use
C◗Wind and store excess mains cord in the wall
holder.
ENGLISH6

C◗Screw the wall holder to the wall with the
screws supplied with the appliance.
◗You can also place the vacuum cleaner and
the wall holder FLAT on a table during
charging.
C◗The crevice tool,floor nozzle,squeegee and
the stick can be attached to the wall holder
by pushing them into the appropriate
fastening slots.
Charging the appliance
1Make sure that the slide switch of the
vacuum cleaner is in off position (0) during
charging.The appliance will not charge if
the slide switch is in another position.
2Insert the charger plug into the wall
socket.
C3Always put the vacuum cleaner back onto
the holder after use to recharge the
batteries,even if the batteries are still
almost fully charged.
C◗The indicator light will come on to indicate
that the appliance is charging.
The indicator light will stay on as long as the
appliance is connected to the wall holder and the
plug is in the wall socket.
The indicator light does not give any information
about the charge level of the built-in batteries.
ENGLISH 7

Charge the appliance for at least 16 hours before
you use it for the first time.
Recharge the appliance as soon as the motor
power decreases noticeably.
If you are not going to use the appliance for a
longer period of time,we advise you to remove
the charger plug from the wall socket to save
energy.
Vacuum cleaning
C1Set the slide switch to position I for
normal suction power.Set it to position II
for turbo suction power.
Connecting accessories
Hard floors and carpets
C1Use the floor nozzle for vacuum cleaning
hard floors and carpets.
ENGLISH8

Fluff and hair
C1Assemble the fluff collector onto the
nozzle of the appliance or onto the floor
nozzle.Use the fluff collector to remove
hair or fluff.
Pass the fluff collector gently over the hairs or fluff
to be removed.The hairs or fluff will be worked
loose from the surface,collected and then sucked
up.
Hard-to-reach places
C1Use the crevice tool for vacuum cleaning
hard-to-reach places.
Extra reach
C1You can assemble the stick for extra reach
when cleaning hard floors,carpets and
hard-to-reach areas.Push the narrow part
of the stick into the hole in the handle
until you hear a click.
C◗You can switch the appliance on by means of
the slide switch on the handle of the stick.
The appliance may only be used in position II
(turbo suction power) if the stick is attached.
ENGLISH 9

C2To detach the stick,press the release
button underneath the handle of the
vacuum cleaner and pull the stick out of
the appliance.
Liquids
Insert the deflector into the dust compartment if
you want to suck up liquids.
C1Press the break button and open the
vacuum cleaner.
C2Remove the dustbag from the dust
compartment.
C3Insert the deflector and the filter into the
dust compartment.
C4Push the filter firmly into the dust
compartment.
ENGLISH10