Phoenix Contact ILC 130 ETH User manual

onlinecomponents.com
AUTOMATION
UM EN ILC 1XX
Order No.: —
User Manual
Installing and operating the ILC 130 ETH,
ILC 150 ETH, ILC 155 ETH, and
ILC 170 ETH 2TX Inline Controllers

onlinecomponents.com

onlinecomponents.com
Designation:
Revision:
Order No.:
This user manual is valid for:
AUTOMATION
7805_en_02 PHOENIX CONTACT
11/2008
Installing and operating the ILC 130 ETH, ILC 150 ETH, ILC 155 ETH and,
ILC 170 ETH 2TX Inline Controllers
UM EN ILC 1XX
02
—
Designation From Revision (HW) From Revision (FW) Order No.
ILC 130 ETH 01 3.01 2988803
ILC 150 ETH 00 2.00 2985330
ILC 155 ETH 01 2.04 2988188
ILC 170 ETH 2TX 01 3.00 2916532
User Manual

onlinecomponents.com
UM EN ILC 1XX
PHOENIX CONTACT 7805_en_02
Please observe the following notes
In order to ensure the safe use of the product described, you have to read and understand
this manual. The following notes provide information on how to use this manual.
User group of this manual
The use of products described in this manual is oriented exclusively to qualified electricians
or persons instructed by them, who are familiar with applicable standards and other
regulations regarding electrical engineering and, in particular, the relevant safety concepts.
Phoenix Contact accepts no liability for erroneous handling or damage to products from
Phoenix Contact or third-party products resulting from disregard of information contained in
this manual.
Explanation of symbols used and signal words
The following types of messages provide information about possible property damage and
general information concerning proper operation and ease-of-use.
This is the safety alert symbol. It is used to alert you to potential personal injury
hazards. Obey all safety messages that follow this symbol to avoid possible
injury or death.
DANGER
This indicates a hazardous situation which, if not avoided, will result in death or serious
injury.
WARNING
This indicates a hazardous situation which, if not avoided, could result in death or serious
injury.
CAUTION
This indicates a hazardous situation which, if not avoided, could result in minor or
moderate injury.
NOTE
This symbol and the accompanying text alerts the reader to a situation which may cause
damage or malfunction to the device, either hardware or software, or surrounding
property.
This symbol and the accompanying text provides additional information to the reader. It is
also used as a reference to other sources of information (manuals, data sheets, literature)
on the subject matter, product, etc.

onlinecomponents.com
UM EN ILC 1XX
7805_en_02 PHOENIX CONTACT
General terms and conditions of use for technical documentation
Phoenix Contact reserves the right to alter, correct, and/or improve the technical
documentation and the products described in the technical documentation at its own
discretion and without giving prior notice, insofar as this is reasonable for the user. The
same applies to any technical changes that serve the purpose of technical progress.
The receipt of technical documentation (in particular data sheets, installation instructions,
manuals, etc.) does not constitute any further duty on the part of Phoenix Contact to furnish
information on alterations to products and/or technical documentation. Any other
agreement shall only apply if expressly confirmed in writing by Phoenix Contact. Please
note that the supplied documentation is product-specific documentation only and that you
are responsible for checking the suitability and intended use of the products in your specific
application, in particular with regard to observing the applicable standards and regulations.
Although Phoenix Contact makes every effort to ensure that the information content is
accurate, up-to-date, and state-of-the-art, technical inaccuracies and/or printing errors in
the information cannot be ruled out. Phoenix Contact does not offer any guarantees as to
the reliability, accuracy or completeness of the information. All information made available
in the technical data is supplied without any accompanying guarantee, whether expressly
mentioned, implied or tacitly assumed. This information does not include any guarantees
regarding quality, does not describe any fair marketable quality, and does not make any
claims as to quality guarantees or guarantees regarding the suitability for a special purpose.
Phoenix Contact accepts no liability or responsibility for errors or omissions in the content
of the technical documentation (in particular data sheets, installation instructions, manuals,
etc.).
The aforementioned limitations of liability and exemptions from liability do not apply, in so
far as liability must be assumed, e.g., according to product liability law, in cases of
premeditation, gross negligence, on account of loss of life, physical injury or damage to
health or on account of the violation of important contractual obligations. Claims for
damages for the violation of important contractual obligations are, however, limited to
contract-typical, predictable damages, provided there is no premeditation or gross
negligence, or that liability is assumed on account of loss of life, physical injury or damage
to health. This ruling does not imply a change in the burden of proof to the detriment of the
user.

onlinecomponents.com
UM EN ILC 1XX
PHOENIX CONTACT 7805_en_02
Statement of legal authority
This manual, including all illustrations contained herein, is copyright protected. Use of this
manual by any third party is forbidden. Reproduction, translation, and public disclosure, as
well as electronic and photographic archiving or alteration requires the express written
consent of Phoenix Contact. Violators are liable for damages.
Phoenix Contact reserves all rights in the case of patent award or listing of a registered
design. Third-party products are always named without reference to patent rights. The
existence of such rights shall not be excluded.
How to contact us
Internet Up-to-date information on Phoenix Contact products and our Terms and Conditions can be
found on the Internet at:
www.phoenixcontact.com.
Make sure you always use the latest documentation.
It can be downloaded at:
www.phoenixcontact.com.
Subsidiaries If there are any problems that cannot be solved using the documentation, please contact
your Phoenix Contact subsidiary.
Subsidiary contact information is available at www.phoenixcontact.com.
Published by .
Should you have any suggestions or recommendations for improvement of the contents and
layout of our manuals, please send your comments to
[email protected].
PHOENIX CONTACT GmbH & Co. KG
Flachsmarktstraße 8
32825 Blomberg
Germany
Phone +49 - (0) 52 35 - 3-00
Fax +49 - (0) 52 35 - 3-4 12 00
PHOENIX CONTACT
P.O. Box 4100
Harrisburg, PA 17111-0100
USA
Phone [phone]

onlinecomponents.com
7805_en_02 PHOENIX CONTACT i
Table of Contents
1 Preface ....................................................................................................................................1-1
1.1 Purpose of this manual .......................................................................................1-1
1.2 Hardware and software requirements.................................................................1-1
2 Description of the Inline Controller ...........................................................................................2-1
2.1 General description of the Inline Controller.........................................................2-1
2.2 Possible fields of application of the Inline Controller...........................................2-2
2.2.1 ILC 130 ETH .......................................................................................2-2
2.2.2 ILC 150 ETH, ILC 155 ETH, and ILC 170 ETH 2TX ............................2-3
2.3 Notes on using the Inline Controller (ILC 150 ETH/ILC 155 ETH)
in potentially explosive areas..............................................................................2-4
2.4 Unpacking the Inline Controller........................................................................... 2-5
2.5 Connection and operating elements...................................................................2-6
2.6 Diagnostic and status indicators.........................................................................2-8
2.7 Mode selector switch........................................................................................2-10
2.8 Reset button (concealed) .................................................................................2-11
2.9 Parameterization memory.................................................................................2-11
2.10 Internal basic circuit diagram............................................................................2-13
2.11 Mounting and removing the Inline Controller ....................................................2-14
2.12 Communication paths.......................................................................................2-17
2.12.1 Ethernet ............................................................................................2-18
2.12.2 Serial PRG interface (Mini-DIN female connector) ............................2-19
2.13 Serial PRG interface .........................................................................................2-20
2.13.1 Function blocks for devices connected to PRG .................................2-20
2.13.2 RS232_INIT ......................................................................................2-21
2.13.3 RS232_RECEIVE ............................................................................. 2-24
2.13.4 RS232_SEND ...................................................................................2-26
2.13.5 Error codes of the STATUS output ....................................................2-27
2.14 INTERBUS ..............................................................................................2-28
2.14.1 Local bus ..........................................................................................2-28
2.14.2 Remote bus ......................................................................................2-28
2.15 Power supply....................................................................................................2-29
2.15.1 Sizing of the power supply ................................................................2-29
2.15.2 Power supply connection ..................................................................2-30
2.15.3 24 V segment supply/24 V main supply ............................................2-32
2.15.4 24 V segment supply ........................................................................2-32
2.15.5 24 V main voltage .............................................................................2-32
2.15.6 24 V ILC supply .................................................................................2-33
2.15.7 Jumpers ............................................................................................2-33
2.16 Digital inputs and outputs .................................................................................2-34

onlinecomponents.com
UM EN ILC 1XX
ii PHOENIX CONTACT 7805_en_02
3 The Inline Controller under PC WorX.......................................................................................3-1
3.1 Software version................................................................................................. 3-1
3.2 Assigning the IP address for the controller/BootP server....................................3-2
3.3 Setting the realtime clock under PC WorX Express ............................................3-5
3.4 "Download Changes" .........................................................................................3-5
3.5 Parameterization memory and Internet Explorer.................................................3-6
3.5.1 Internet Explorer FTP function ............................................................3-7
3.5.2 Activating/deactivating the FTP server ................................................ 3-7
3.5.3 Activating/deactivating the HTTP server .............................................3-8
3.6 Function blocks for handling files in the parameterization memory.....................3-9
3.7 Function blocks for Ethernet communication....................................................3-10
3.8 Function blocks for PCP communication ..........................................................3-11
3.9 Alignment .........................................................................................................3-12
4 System variables and status information..................................................................................4-1
4.1 General information ............................................................................................4-1
4.2 Status register for local digital inputs and outputs...............................................4-1
4.3 Diagnostic status register ...................................................................................4-2
4.4 Diagnostic parameter register.............................................................................4-3
4.5 IEC 61131 runtime system..................................................................................4-4
4.6 Control processor ...............................................................................................4-5
4.7 Battery, realtime clock ........................................................................................ 4-6
4.8 Power supplies ...................................................................................................4-6
4.9 Mode selector switch..........................................................................................4-6
4.10 System time........................................................................................................4-6
5 Technical data and ordering data ............................................................................................5-1
5.1 Technical data ....................................................................................................5-1
5.2 Ordering data .....................................................................................................5-8
5.2.1 Modules ..............................................................................................5-8
5.2.2 Accessories ........................................................................................5-8
5.2.3 Software ..............................................................................................5-8
5.2.4 Documentation ....................................................................................5-8
A Appendix: Service and maintenance ...................................................................................... A-1
A 1 Error causes and remedies................................................................................ A-1
A 2 Updating the Inline Controller firmware.............................................................. A-1
A 3 Connecting unshielded cables .......................................................................... A-2
B Index....................................................................................................................................... B-1

onlinecomponents.com
Preface
7805_en_02 PHOENIX CONTACT 1-1
1Preface
1.1 Purpose of this manual
This manual helps you to start up and operateanILC130ETH,ILC150ETH,ILC155ETH
or ILC 170 ETH 2TX Inline Controller.
1.2 Hardware and software requirements
Hardware/software Description
Inline Controller ILC 130 ETH ILC 150 ETH ILC 155 ETH ILC 170 ETH 2TX
Parameterization
memory, plug-in
No No No 256 MB, SD card
Ethernet cable Ethernet cable for connecting the Inline Controller to a PC
Connecting cable Connecting cable for connecting the Inline Controller to a PC (V.24 (RS-232)
cable, optional)
Automation software
PC WorX Version 5.20
Service Pack 3 or
later ****
Version 5.10
Service Pack 1 or
later *
Version 5.20 or
later **
Version 5.20
Service Pack 2 or
later ***
PC WorX Express Version 5.20
Service Pack 3 or
later ****
Version 5.20 or
later **
Version 5.20 or
later **
Version 5.20
Service Pack 2 or
later ***
* Part of the AUTOMATIONWORX Software Suite 2007 1.30 Service Pack 1
** Part of the AUTOMATIONWORX Software Suite 2008 1.40
*** Part of the AUTOMATIONWORX Software Suite 2008 1.40 Service Pack 2
**** Part of the AUTOMATIONWORX Software Suite 2008 1.40 Service Pack 3
For the ordering data for hardware, software, and additional documentation, please refer
to "Technical data and ordering data" on page 5-1.

onlinecomponents.com
UM EN ILC 1XX
1-2 PHOENIX CONTACT 7805_en_02

onlinecomponents.com
Description of the Inline Controller
7805_en_02 PHOENIX CONTACT 2-1
2 Description of the Inline Controller
2.1 General description of the Inline Controller
The Inline Controller is a compact controller with integrated Ethernet and INTERBUS
connections.
IEC 61131 control
performance
The Inline Controller is seamlessly configured and programmed according to IEC 61131
using the PC WorX automation software. PC WorX can be operated via the network
(Ethernet). The powerful processor can be programmed in all five IEC 61131 programming
languages and ensures quick control task processing.
Integrated Ethernet
connection
The integrated Ethernet connection (using twisted pair cable) provides for the Ethernet
connectivity. Throughout the Ethernet network, the Inline Controller can be accessed via
Ethernet and TCP/IP or UDP/IP. The ILC 170 ETH 2TX has two fully implemented Ethernet
connections, which are switched inside the device.
Integrated communication functions enable direct and effective data exchange via
Ethernet. The Ethernet network provides universal options for communicating with the Inline
Controller. Using the send and receive communication blocks, information, e.g., necessary
coupling variables, can be exchanged between Inline Controllers via Ethernet. This enables
distributed, modular automation solutions to be configured.
The existing IEC 61131-5 blocks have thus been extended to include a transparent TCP/IP
mode and a transparent UDP/IP mode.
When using the AX OPC server provided in the AUTOMATIONWORX Software Suite
Version 1.30 or later, Inline Controller data is available in the Ethernet network in a
standardized format and can be used for the different visualization packages.
Integrated INTERBUS
connection
An Inline local bus as well as an INTERBUS remote bus can be connected via the INTERBUS
connection. In this way you can create a complete INTERBUS system (maximum of 4 remote
bus levels) using the Inline Controller as the distributed control system.
The I/O level is connected to the Inline Controller using INTERBUS.
The ILC 130 ETH, ILC 150 ETH and ILC 155 ETH Inline Controllers have the same
appearance and numerous identical functions.
The main difference lies in the varying memory sizes, which are available to the user.
The ILC 150 ETH and ILC 155 ETH Inline Controllers are approved for use in zone 2
potentially explosive areas. Observe the notes in Section 2.3 on page 2-4.
The ILC 170 ETH 2TX Inline Controller also has a second Ethernet interface and a slot for
an SD memory card (parameterization memory).
In the following, the term Inline Controller is used in general. For additional information
about the different memory sizes, please refer to Section 5.1, "Technical data" from
page 5-1 onwards.
Please note that the ILC 130 ETH does not support connection of the INTERBUS remote
bus.

onlinecomponents.com
UM EN ILC 1XX
2-2 PHOENIX CONTACT 7805_en_02
V.24 (RS-232) interface This interface can be used to either assign the IP address of the Inline Controller and
access the controller using the Diag+ diagnostic tool or communicate with serial I/O devices
via function blocks.
ILC 170 ETH 2TX:
Parameterization memory
(SD card)
The ILC 170 ETH 2TX has a plug-in parameterization memory in the form of an SD card.
This memory can be used to save programs and configurations, which belong to your
project, e.g., the visualization project.
2.2 Possible fields of application of the Inline
Controller
2.2.1 ILC 130 ETH
The ILC 130 ETH Inline Controller can be used as a distributed control system of an Inline
station, which is connected to an Ethernet system.
A single Inline local bus (Figure 2-2) can be connected to the Inline Controller.
Figure 2-1 Connected Inline local bus
The Inline Controller cannot be programmed via the V.24 (RS-232) interface.
The parameterization memory is not supplied as standard with the ILC 170 ETH 2TX. For
the ordering data, please refer to "Accessories" on page 5-8.
NOTE: Use only a parameterization memory provided by Phoenix Contact:
256 MB parameterization memory:
SD FLASH 256MB Order No. 2988120
NOTE: Parameterization memory (SD card) – formatting note
The SD card is preformatted and designed for use with Phoenix Contact devices. Ensure
that the SD card is not reformatted.
Please note that the ILC 130 ETH does not support connection of the INTERBUS remote
bus.
Ethernet
7805A020
AUTOMATIONWORX
UL
US
UM
FF
I1
I3
I2
I4
ILC 130 ETH
Order-No.: 2988803
HW/FW: 01/301
MAC Addr.: xx.xx.xx.xx
RESET
Q4
E
I5
I7
I6
I8
PRG
LNK ACT
Q3
Q2Q1
RDY FAIL BSA PFFR
RUN / PROG
MRESET
STP
X2
X1

onlinecomponents.com
Description of the Inline Controller
7805_en_02 PHOENIX CONTACT 2-3
2.2.2 ILC 150 ETH, ILC 155 ETH, and ILC 170 ETH 2TX
The ILC 150 ETH/ILC 155 ETH/ILC 170 ETH 2TX Inline Controller can be used as a
distributed control system of an Inline station, which is connected to an Ethernet system.
A single Inline local bus (Figure 2-2) as well as a complete INTERBUS system with a
maximum of 4 remote bus levels (Figure 2-3) can be connected to the Inline Controller.
Figure 2-2 Connected Inline local bus
Figure 2-3 Remote bus levels
Ethernet
74060001
AUTOMATIONWORX
UL
US
UM
FF
I1
I3
I2
I4
ILC 150 ETH
Order-No.: 2985330
HW/FW: 00/100
MACAddr.: xx.xx.xx.xx
RESET
Q4
E
I5
I7
I6
I8
PRG
LNK ACT
Q3
Q2Q1
RDY FAIL BSA PFFR
RUN / PROG
MRESET
STP
1.
2.
3.
4.
Remote bus levels
1.
2.
3.
4.
Remote bus levels
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
RC
RD
D
RB-T
LD
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DO8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
AUTOMATIONWORX
UL
US
UM
FF
I1
I3
I2
I4
ILC150 ETH
Order-No.:2985330
HW/FW:00/100
MACAddr.: xx.xx.xx.xx
RESET
Q4
E
I5
I7
I6
I8
PRG
LNK ACT
Q3
Q2Q1
RDY FAIL BSA PFFR
RUN/ PROG
MRESET
STP
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DO8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
RC
RD
D
RB-T
LD
RC
RD
D
RB-T
LD
INTERBUS
INTERBUS
INTERBUS
Inline local bus
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
RC
RD
D
RB-T
LD
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DO8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
Inline local bus
1
2
D
DO8
1
2
1
2
1
2
1
2
D
DI2
1
2
D
DI2
1
2
D
DI2
1
2
D
DO8
1
2
1
2
1
2
BA
RC
UL
UM
RD
LD
US
7805A005
RC
RD
D
RB-T
LD
RC
RD
D
RB-T
LD
INTERBUS
INTERBUS
INTERBUS
AUTOMATIONWORX
UL
US
UM
FF
I1
I3
I2
I4
ILC170 ETH 2TX
Order-No.:2916532
HW/FW:00/220
MACAddr.: xx.xx.xx.xx
RESET
Q4
E
I5
I7
I6
I8
PRG
LNK
LNK
ACT
ACT
X2.2
X2.1
X1
Q3
Q2Q1
RDY FAIL BSA PF
FR
RUN/PROG
MRESET
STOP

onlinecomponents.com
UM EN ILC 1XX
2-4 PHOENIX CONTACT 7805_en_02
2.3 Notes on using the Inline Controller
(ILC 150 ETH/ILC 155 ETH) in potentially explosive
areas
Approval according to EC Directive 94/9 (ATEX) II 3G Ex nAC II T4 X
The Inline Controller (ILC 150 ETH/ILC 155 ETH) conforms to the requirements of
protection type "n" and can be installed in a zone 2 potentially explosive area. The Inline
Controller (ILC 150 ETH/ILC 155 ETH) is a category 3G item of electrical equipment.
Figure 2-4 Typical labeling of terminals for use in potentially explosive areas
1. When working on the Inline Controller, always disconnect the supply voltage.
2. The Inline Controller must only be installed, started up, and maintained by qualified
specialist personnel.
3. Mount the Inline bus coupler in a control cabinet or metal housing. The minimum
requirement for both items is IP54 protection according to EN 60529.
4. The Inline Controller must not be subject to mechanical strain and thermal loads, which
exceed the limits specified in the product documentation.
5. The Inline Controller must not be repaired by the user. Repairs may only be carried out
by the manufacturer. The Inline Controller is to be replaced by an approved controller
of the same type.
6. Only category 3G equipment may be connected to Inline Controllers in zone 2.
7. Observe all applicable standards and national safety and accident prevention
regulations for installing and operating equipment.
WARNING: Explosion hazard
Only Inline terminals that are approved for use in potentially explosive areas may
be snapped onto the Inline Controller.
Before using an Inline terminal in a zone 2 potentially explosive area, first check that the
terminal has been approved for installation in this area.
For a list of terminals approved for zone 2 potentially explosive areas, please refer to the
AH EN IL EX ZONE 2 application note.
Check the labeling on the Inline terminal and the packaging (see Figure 2-4).
WARNING: Explosion hazard
Before startup, ensure that the following points and instructions are observed.
5561C001
INTERBUS
GL
U
L
xx
Potential routing 4 A maximum
Potential routing 4 A maximum
for use in Ex areas
for use in Ex areas
II 3G Ex nAC IIC T4 X
II 3G Ex nAC IIC T4 X
LISTED
31ZN
Proc. Ctrl. Eqpt. For Haz. Locs.
Proc. Ctrl. Eqpt. For Haz. Locs.
Cl. I, Zn. 2, AEx nC IIC T5
Cl. I, Zn. 2, AEx nC IIC T5
Cl. I, Zn. 2, Ex nC IIC T5
Cl. I, Zn. 2, Ex nC IIC T5
Cl. I, Div. 2, Grp. A,B,C,D T5
Cl. I, Div. 2, Grp. A,B,C,D T5
IBx IL xx xx x
IBx IL xx xx x
Order-No.: xxxxxxx
Order-No.: xxxxxxx
Module-ID: xx HW/FW XX/-
Module-ID: xx HW/FW XX/-

onlinecomponents.com
Description of the Inline Controller
7805_en_02 PHOENIX CONTACT 2-5
Restrictions
2.4 Unpacking the Inline Controller
The Inline Controller is supplied in an ESD bag together with a package slip with installation
instructions. Please read the complete package slip carefully before unpacking the Inline
Controller.
WARNING: Explosion hazard
When using the controller in potentially explosive areas, observe the technical data and
limit values specified in the corresponding documentation (user manual, package slip).
WARNING: Explosion hazard; restrictions regarding the Inline system
– Please make sure that the maximum permissible current of 8 A flowing through
the potential jumpers UMand US(total current) is not exceeded when using the Inline
terminals in potentially explosive areas.
–When terminal points 1.1 and 2.1 (or 2.2) are jumpered, a maximum
permissible current of 2.5 A (see "24 V segment supply" on page 2-32) flowing
through the potential jumpers UMand US(total current) must not be exceeded when
using the Inline terminals in potentially explosive areas.
NOTE: Electrostatic discharge
The Inline Controller contains components that can be damaged or destroyed by
electrostatic discharge. When handling the Inline Controller, observe the necessary
safety precautions against electrostatic discharge (ESD) according to EN 61340-5-1 and
EN 61340-5-2.
NOTE:
To avoid possible damage to the Inline Controller, unpack and pack the controller in
accordance with the ESD regulations.

onlinecomponents.com
UM EN ILC 1XX
2-6 PHOENIX CONTACT 7805_en_02
2.5 Connection and operating elements
ILC 130 ETH, ILC 150 ETH,
ILC 155 ETH
Figure 2-5 Structure of the Inline Controller (ILC 130 ETH, ILC 150 ETH, ILC 155 ETH)
The Inline Controller consists of the following components:
1Electronics base
2Mode selector switch
3Reset button
4V.24 (RS-232) interface
5Ethernet connection
6Connector 1: Terminal points for voltage supply
7Connector 2: Output terminal points
8Connectors 3 and 4: Input terminal points
9Diagnostic and status indicators
10 End plate
AUTOMATIONWORX
ILC 150 ETH
Order-No.: 2985330
HW/FW: 00/100
MAC Addr.: xx.xx.xx.xx
UL
US
UM
I1
I3
I2
I4
I6I5
I8I7
RESET
E
Q2
Q1
Q3Q4
1
PRG
FF
LNKACT
MRESET
RUN/PROG
STOP
FR PFRDY FAIL
6
7
8
3
2
4
57805A006
1
BSA
9
10

onlinecomponents.com
Description of the Inline Controller
7805_en_02 PHOENIX CONTACT 2-7
ILC 170 ETH 2TX
Figure 2-6 Structure of the Inline Controller (ILC 170 ETH 2TX)
The Inline Controller consists of the following components:
1Electronics base
2Slot for the parameterization memory/card holder (SD card)
3Mode selector switch
4Reset button
5V.24 (RS-232) interface (X1)
6Ethernet interfaces (X2.1/X2.2)
7Connector 1: Terminal points for voltage supply
8Connector 2: Output terminal points
9Connectors 3 and 4: Input terminal points
10 Diagnostic and status indicators
11 End plate
The SD card is not supplied as standard with the ILC 170 ETH 2TX. Please refer to the
ordering data in "Accessories" on page 5-8.
E
Q2
Q1
Q3 Q4
UL
US
UM
FF
FR
I6
I5
I8I7
1
BSA PF
I1
I3
I2
I4
1
RDY FAIL
AUTOMATIONWORX
ILC 170 ETH 2TX
Order-No.: 2916532
HW/FW: 00/220
MAC Addr.: xx.xx.xx.xx
RESET
X1
X2.1
X2.2
PRG
LNK
LNK
ACT
ACT
MRESET
RUN/PROG
STOP
7805A001
1
3
2
4
5
10
7
8
9
11
6

onlinecomponents.com
UM EN ILC 1XX
2-8 PHOENIX CONTACT 7805_en_02
2.6 Diagnostic and status indicators
The diagnostic and status indicators are used for quick local error diagnostics.
Figure 2-7 Diagnostic and status indicators
Local diagnostic and status indicators
The descriptions for diagnostic and status indicators apply to all the Inline Controllers
listed on the inner cover page of this manual.
AUTOMATIONWORX
ILC 150 ETH
Order-No.: 2985330
HW/FW: 00/100
MAC Addr.: xx.xx.xx.xx
UL
US
UM
I1
I3
I2
I4
I6I5
I8I7
RESET
E
Q2
Q1
Q3Q4
1
PRG
FF
LNKACT
MRESET
RUN/PROG
STOP
FR PFRDY FAIL
BF
DIA
UL
US
UM
6
O1
I1
I2
Q4
E
I1
I3
I2
I4
I5
I7
I6
I8
PLC/PWR
BSA PF
FAILRDY
Q3
Q2Q1
FR
FF
ETH
LNK ACT
7805A007
BSA
Des. Color Meaning
ETH: State of the Ethernet interface (for ILC 170 ETH 2TX, applies to both interfaces (X2.1, X2.2))
LNK Green Connection established successfully (link)
ON: The Inline Controller is able to contact another network device
ACT Yellow Data transmission (activity)
ON: Ethernet interface transmitting or receiving data
PLC: Diagnostics of the Inline Controller
FR Green Inline Controller running
OFF: IEC 61131 runtime system not ready to operate
Flashing: IEC 61131 runtime system successfully initialized.
Control function in READY/STOP state, program not processed.
ON: IEC 61131 runtime system successfully initialized and program running.
Control function in RUN state.
FF Yellow Failure
ON: A runtime error has occurred in the IEC 61131 runtime system program
OFF: No runtime error has occurred in the IEC 61131 runtime system program

onlinecomponents.com
Description of the Inline Controller
7805_en_02 PHOENIX CONTACT 2-9
FR + FF Flashing
Only applies for ILC 170 ETH 2TX:
There is no SD card in the controller
PWR: Supply voltage
(see also "Remote bus" on page 2-28)
UL Green 24 V supply UILC for generating the voltages ULand UANA
ON: Supply voltage present
(indication if 24 V supply voltage UILC present)
US Green 24 V supply for segment circuit
ON: Supply voltage present
UM Green 24 V supply for main circuit
ON: Supply voltage present
IL: Diagnostics for INTERBUS
RDY Green INTERBUS master ready to operate/data transmission active
(INTERBUS ready/running)
Flashing: INTERBUS master in READY or ACTIVE state
ON: INTERBUS master in RUN state
FAIL Red Failure
ON: One of the following errors has occurred:
- Bus error in the connected bus (remote bus/local bus)
- Controller error
BSA Yellow Bus segment aborted
ON: One or more bus segments in the connected bus are switched off
PF Yellow Peripheral fault
ON: Peripheral fault of a device in the connected bus (local bus or remote bus)
I/O: Digital inputs and outputs
I1 to I8 Yellow Inputs 1 to 8
ON: Corresponding input is set
EYellow Error
ON: Short circuit/overload at outputs 1 to 4
Q1 to Q4 Yellow Outputs 1 to 4
ON: Corresponding output is set
Des. Color Meaning

onlinecomponents.com
UM EN ILC 1XX
2-10 PHOENIX CONTACT 7805_en_02
2.7 Mode selector switch
The mode selector switch is used to define the operating state of the application program.
The RUN/PROG and STOP positions have a toggle button function and the MRESET
position a pushbutton function. After releasing the button in the MRESET position, it returns
to the STOP position.
Figure 2-8 Mode selector switch
Table 2-1 Inline Controller operating modes
Operating
mode
Explanation
RUN/PROG The application program is in the RUN state.
The PC WorX/PC WorX Express software can be used for program
and configuration modifications.
The monitoring and online functions can be used.
STOP The application program is in the STOP state.
MRESET Retain data and the application program are deleted.
For safety reasons, set the mode selector switch in the following
sequence to perform deletion:
•Set the switch to the MRESET position for three seconds.
•Release the switch for three seconds.
•Set the switch to the MRESET position for three seconds.
AUTOMATIONWORX
ILC150ETH
Order-No.: 2985330
HW/FW:00/100
MACAddr.: xx.xx.xx.xx
UL
US
UM
I1
I3
I2
I4
I6
I5
I8I7
RESET
E
Q2
Q1
Q3 Q4
1
PRG
FF
LNK ACT
MRESET
RUN/PROG
STOP
FR PFRDY FAI L
7406B005
RUN / PROG
MRESET
STOP
BSA