Phoenix Contact AXC F 1152 How to use

User manual
Installing, starting up, and operating the
AXC F 1152, AXC F 2152 and AXC F 3152
controllers

2020-09-30
PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
phoenixcontact.com
107708_en_08
Installing, starting up, and operating the AXC F 1152, AXC F 2152 and
AXC F 3152 controllers
Designation As of version (HW) As of version (FW) Order No.
AXC F 1152 03 2020.0 LTS 1151412
AXC F 2152 03 2020.0 LTS 2404267
AXC F 3152 01 2020.3 1069208
Before starting up the controller, observe the following:
• Make sure you always operate the controller with the latest firmware version.
The current firmware version can be downloaded at:
– AXC F 1152: phoenixcontact.net/product/1151412
– AXC F 2152: phoenixcontact.net/product/2404267
– AXC F 3152: phoenixcontact.net/product/1069208
• Observe the change notes regarding the firmware version.
• If necessary, update the firmware.
For information on running firmware updates, refer to “Web-based management (WBM)” on page 81 and
Section A 3.
User manual
This user manual is valid for:
UM EN AXC F X152, Revision 08

Table of contents
107708_en_08 PHOENIX CONTACT 3 / 112
Table of contents
1 For your safety ...........................................................................................................................7
1.1 Identification of warning notes ............................................................................... 7
1.2 Qualification of users ............................................................................................. 7
1.3 Field of application of the product..........................................................................8
1.3.1 Intended use .......................................................................................... 8
1.4 Product changes ................................................................................................... 8
1.5 Safety notes .......................................................................................................... 8
1.6 Security in the network .......................................................................................... 9
1.7 UL warning notes................................................................................................. 10
1.8 Notes on using the AXC F 2152 controller in potentially explosive areas............. 10
2 Transport, storage, and unpacking ..........................................................................................12
2.1 Transport............................................................................................................. 12
2.2 Storage................................................................................................................ 12
2.3 Unpacking ........................................................................................................... 12
3 Description of the controllers ...................................................................................................14
3.1 General description of the controllers ..................................................................14
3.2 Licensing information regarding open-source software ....................................... 17
3.3 Requesting the source code................................................................................17
3.4 Directory structure of the file system.................................................................... 17
3.5 Using SFTP to access the file system.................................................................. 18
3.6 Firewall ................................................................................................................ 19
3.7 Possible fields of application of the controller ...................................................... 19
3.7.1 The controller as a distributed controller of an Axioline F sta-
tion ....................................................................................................... 19
3.7.2 The controller as a PROFINET controller in a PROFINET net-
work ..................................................................................................... 20
3.7.3 The controller as a PROFINET device in a PROFINET network ..............
21
3.8 Components of the controller .............................................................................. 22
3.8.1 Connection and operating elements .................................................... 22
3.8.2 Printing ................................................................................................. 24
3.9 Diagnostic and status indicators.......................................................................... 26
3.10 Mode selector switch (AXC F 3152) .................................................................... 30
3.11 Reset button ........................................................................................................ 31
3.12 Parameterization memory.................................................................................... 33
3.13 SD card (optional)................................................................................................ 33

AXC F X152
4 / 112 PHOENIX CONTACT 107708_en_08
3.14 Internal basic circuit diagram ............................................................................... 36
3.15 Communication paths.......................................................................................... 38
3.15.1 Ethernet ............................................................................................... 39
3.16 Supply connector................................................................................................. 39
3.17 Bus base module................................................................................................. 40
4 Mounting hardware ..................................................................................................................42
4.1 Safety notes ...................................................................................................... 42
4.2 Basic information................................................................................................. 43
4.3 Structure of an Axioline F station ......................................................................... 45
4.4 Structure of a PLCnext Inline station.................................................................... 47
4.5 Mounting the controller........................................................................................ 48
4.6 Inserting the SD card ................................................................................ 49
4.7 Mounting a left-alignable Axioline F extension module ........................................50
4.8 Mounting the AXC F IL ADAPT Inline adapter terminal........................................ 50
5 Connecting and wiring hardware ..............................................................................................51
5.1 Supply voltage..................................................................................................... 51
5.1.1 Sizing of the power supply ...................................................................51
5.1.2 Connecting the power supply ...............................................................52
5.2 Connecting Ethernet............................................................................................ 54
6 Startup .....................................................................................................................................55
6.1 Installing PLCnext Engineer ................................................................................ 55
6.2 User interface ...................................................................................................... 56
6.3 Creating a new project......................................................................................... 57
6.4 Configuring the IP settings................................................................................... 58
6.4.1 Setting the IP address range ................................................................ 58
6.4.2 Setting the IP address .......................................................................... 60
6.5 Connecting to the controller................................................................................. 61
7 Transferring variable values to PROFICLOUD .........................................................................64
8 System variables and status information ..................................................................................65
8.1 General information ............................................................................................. 65
8.2 Data structures .................................................................................................... 65
8.3 System time......................................................................................................... 67
8.4 Power supplies .................................................................................................... 67
8.5 TCP_SOCKET, UDP_SOCKET, and TLS_SOCKET function blocks..................67

Table of contents
107708_en_08 PHOENIX CONTACT 5 / 112
8.6 Device status....................................................................................................... 68
8.7 Partition ............................................................................................................... 69
8.8 Task handling ...................................................................................................... 70
8.9 Client connections to a PLCnext Engineer HMI web server.................................72
8.9.1 HMI_STATUS system variable ............................................................ 72
8.9.2 HMI_CONTROL system variable ......................................................... 73
8.10 Axioline F: Diagnostic status register................................................................... 74
8.11 Axioline F: diagnostic parameter register............................................................. 75
8.12 PROFINET system variables............................................................................... 76
8.13 INTERBUS: master diagnostic status register ..................................................... 78
8.14 INTERBUS: master diagnostic parameter register .............................................. 79
9 Web-based management (WBM) ............................................................................................81
10 Removing hardware .................................................................................................................82
10.1 Safety notes ...................................................................................................... 82
10.2 Removing cables................................................................................................. 83
10.3 Removing the connector...................................................................................... 83
10.4 Removing the SD card......................................................................................... 84
10.5 Removing the controller....................................................................................... 85
10.6 Removing a left-alignable Axioline F extension module....................................... 85
10.7 Removing the AXC F IL ADAPT Inline adapter terminal ...................................... 85
11 Device replacement, device defects, and repairs ....................................................................86
11.1 Device replacement............................................................................................. 86
11.2 Device defects and repair.................................................................................... 87
12 Maintenance, decommissioning, and disposal ........................................................................88
12.1 Maintenance........................................................................................................ 88
12.2 Decommissioning and disposal........................................................................... 88
13 Troubleshooting and frequently asked questions (FAQs) ........................................................89
14 Ordering data and technical data .............................................................................................91
14.1 Ordering data ...................................................................................................... 91
14.2 Overview of documentation................................................................................. 92
14.3 Technical data of the AXC F 1152 and AXC F 2152 ............................................ 93
14.4 AXC F 3152 technical data .................................................................................. 98

AXC F X152
6 / 112 PHOENIX CONTACT 107708_en_08
A Appendix ................................................................................................................................102
A 1 Updating the firmware via the shell.................................................................... 102
A 2 Shell commands for controlling the firmware ..................................................... 102
A 3 Replacing the HTTPS certificate........................................................................ 102
A 4 Use of the AXC F 2152 controller under extreme ambient conditions................ 103
B Appendix for document lists....................................................................................................104
B 1 List of figures ..................................................................................................... 104
B 2 List of tables ......................................................................................................107
B 3 Index.................................................................................................................. 109

For your safety
107708_en_08 PHOENIX CONTACT 7 / 112
1Foryoursafety
Read this user manual carefully and keep it for future reference.
1.1 Identification of warning notes
1.2 Qualification of users
The use of products described in this user manual is oriented exclusively to:
– Electrically skilled persons or persons instructed by them. The users must be familiar
with the relevant safety concepts of automation technology as well as applicable stan-
dards and other regulations.
– Qualified application programmers and software engineers. The users must be familiar
with the relevant safety concepts of automation technology as well as applicable stan-
dards and other regulations.
This symbol indicates hazards that could lead to personal injury.
There are three signal words indicating the severity of a potential injury.
DANGER
Indicates a hazard with a high risk level. If this hazardous situation is not
avoided, it will result in death or serious injury.
WARNING
Indicates a hazard with a medium risk level. If this hazardous situation is not
avoided, it could result in death or serious injury.
CAUTION
Indicates a hazard with a low risk level. If this hazardous situation is not avoided,
it could result in minor or moderate injury.
This symbol together with the NOTE signal word warns the reader of actions
that might cause property damage or a malfunction.
Here you will find additional information or detailed sources of information.

AXC F X152
8 / 112 PHOENIX CONTACT 107708_en_08
1.3 Field of application of the product
1.3.1 Intended use
The AXC F 1152 and AXC F 2152 controllers are modular small-scale controllers. The
AXC F 3152 is a modular controller that can be used for smaller and medium-sized applica-
tions. The devices comply with the IP20 protection class and are designed for use in closed
control cabinets or control boxes (terminal boxes) with an IP54 degree of protection or
higher.
The devices are designed for use in industrial environments.
1.4 Product changes
Modifications to the device hardware are not permitted.
Incorrect operation or modifications to the devices can endanger your safety or damage the
devices. Do not repair the devices yourself. If a device is defective, please contact
Phoenix Contact.
1.5 Safety notes
Observe the country-specific installation, safety, and accident prevention regulations.
NOTE: Property damage due to impermissible stress
The IP20 degree of protection (IEC 60529/EN 60529) requires that the device is used in
a clean and dry environment. If you use the device in an environment that is outside of the
specified limits, this may cause damage to the device.
• Do not subject the device to mechanical and/or thermal loads that exceed the speci-
fied limits.
NOTE: Electrostatic discharge
The device contains components that can be damaged or destroyed by electrostatic dis-
charge. When handling the device, observe the necessary safety precautions against
electrostatic discharge (ESD) in accordance with EN 61340-5-1 and IEC 61340-5-1.
NOTE: Device failure due to foreign objects in device
Foreign objects in the device can lead to malfunctions or even device failure.
• Ensure that no foreign objects find their way into the device (e.g., into the vents).
NOTE: Device failure if operated outside the permitted ambient temperature
range
Operating the device in ambient temperatures that are not within the permitted range may
lead to malfunctions or even device failure.
• Ensure that the device is operated within the permitted ambient temperature range,
see Section 14.3 and Section 14.4.

For your safety
107708_en_08 PHOENIX CONTACT 9 / 112
1.6 Security in the network
NOTE: Device failure due to vibrations and shock levels above the permitted
specifications during operation
If the device is subjected to vibrations and shock levels above the permitted specifications
during operation, this may lead to malfunctions or even device failure.
• Ensure that the permitted specifications for vibrations and shocks are adhered to
when operating the device, see Section 14.3 and Section 14.4.
NOTE: Device defect due to polarity reversal
Polarity reversal puts a strain on the electronics and can damage the device.
• To protect the device, avoid reversing the poles of the 24 V supply.
Please note:
The service interface currently has no function.
The service interface is intended for connecting a PC. The service interface is not intend-
ed for connecting other peripheral devices.
NOTE: Risk of unauthorized network access
Connecting devices to a network via Ethernet always entails the risk of unauthorized ac-
cess to the network.
Therefore, please check your application for the option of deactivating active communi-
cation channels (e.g., FTP, DCP, HTTP, HTTPS, etc.), or setting passwords to prevent
third parties from accessing the controller without authorization and modifying the system.
Due to its communication interfaces, the controller should not be used in safety-critical ap-
plications unless additional security appliances are used.
Please take additional protective measures in accordance with the IT security require-
ments and the standards applicable to your application (e.g., virtual networks (VPN) for
remote maintenance access, firewalls, etc.) for protection against unauthorized network
access.
On first request, you shall release Phoenix Contact and the companies associated with
Phoenix Contact GmbH & Co. KG, Flachsmarktstraße 8, 32825 Blomberg, Germany in
accordance with §§ 15 ff AktG (German Stock Corporation Act), hereinafter collectively
referred to as “Phoenix Contact”, from all third-party claims made due to improper use.
For the protection of networks for remote maintenance via VPN, Phoenix Contact offers
the mGuard product range of security appliances, a description of which you will find in
the latest Phoenix Contact catalog (phoenixcontact.net/products).
Additional measures for protection against unauthorized network access are listed in the
AH EN INDUSTRIAL SECURITY application note. The application note can be down-
loaded at phoenixcontact.net/product/2404267.

AXC F X152
10 / 112 PHOENIX CONTACT 107708_en_08
1.7 UL warning notes
Valid for AXC F 1152 and AXC F 2152
If the device is not used in the specified manner, the protection provided by the device may
be impaired.
SELV - Limited energy according UL/IEC/EN 61010-1 or NEC Class 2
1.8 Notes on using the AXC F 2152 controller in poten-
tially explosive areas
Approval in accordance with ATEX directive 2014/34/EU and IECEx scheme
The category 3 device is designed for installation in zone 2 potentially explosive areas.
The device satisfies the requirements of EN/IEC 60079-0 and EN/IEC 60079-7.
Installation, operation, and maintenance must only be carried out by qualified electricians.
The IP20 degree of protection (IEC 60529/EN 60529) of the device is intended for use in a
clean and dry environment. Do not subject the device to mechanical and/or thermal loads
that exceed the specified limits.
The device must be stopped and immediately removed from the Ex area if it is damaged,
was subjected to an impermissible load, stored incorrectly or if it malfunctions.
The device is not designed for use in atmospheres with a danger of dust explosions.
This device must be installed in an area that is no longer classified as pollution degree 2 in
accordance with IEC 60664-1.
If this device is used in a zone 2 environment, it must be installed in a housing that at least
meets the requirements of IP54 degree of protection in accordance with IEC 60079-7 or an-
other degree of protection in accordance with IEC 60079-0, section 1.
• Follow the installation instructions as described.
Please note:
From 2020 on, the AXC F 2152 is available with approval for potentially explosive areas.
In this case, the approval is printed on the device.
• Before using the device in a potentially explosive area, make sure that your device
has the required approval.
The indicators and certificate numbers of the available approvals are printed on the de-
vice:
–II 3 G Ex ec IIC T4 Gc
– TÜV 19 ATEX 8356 X
– IECEx TUR 19.0031X
WARNING: Explosion hazard
• Please make sure that the following notes and instructions are observed.

For your safety
107708_en_08 PHOENIX CONTACT 11 / 112
• When installing and operating the device, observe the applicable regulations and safe-
ty directives (including national safety directives), as well as general technical regula-
tions. The safety-relevant data is included in this packing slip, the user manual and on
the certificates (manufacturer‘s declaration, additional approvals where applicable). All
documents can be downloaded at
phoenixcontact.net/product/2404267.
• Observe the specified conditions for use in potentially explosive areas. Also observe
the requirements of EN 60079-14.
• Opening or modifying the device is prohibited. Do not repair the device yourself, but re-
place it with an equivalent device. Repairs may only be carried out by the manufacturer.
The manufacturer is not liable for damage resulting from non-compliance.
• The following work is only permitted in potentially explosive areas when the power is
disconnected:
– Snapping the device onto the DIN rail
– Removing the device from the DIN rail
– Connection and disconnection of cables
– Inserting and removing the SD card
• Connect the DIN rail to protective earth ground.
• The switches of the device that can be accessed may only be actuated when the power
supply to the device is disconnected or when it has been ensured that there is no po-
tentially explosive atmosphere present.
• For safe operation, lockable plug connections must have a functional interlock (e.g.,
locking clip, screw connection, etc.). Insert the interlock. Repair any damaged connec-
tors immediately.
• For safe operation with the plug-in parameterization memory (SD card), it must be com-
pletely plugged in and snapped into place.
• For safe operation, all interfaces at the device must be used or covered.
• Please note the following derating values:
Table 1-1 Temperature derating of the AXC F 2152 depending on the altitude
Altitude (above sea level) Maximum ambient temperature
(supply via bus base module)
Up to 2000 m 55°C
2000 m ... 3000 m 49°C

AXC F X152
12 / 112 PHOENIX CONTACT 107708_en_08
2 Transport, storage, and unpacking
2.1 Transport
The device is delivered in cardboard packaging.
• Only transport the device to its destination in its original packaging.
• Observe the instructions on how to handle the package, as well as the moisture, shock,
tilt, and temperature indicators on the packaging.
• Observe the humidity specifications and the temperature range specified for transport
(see Section 14.3 and Section 14.4).
• Protect the surfaces as necessary to prevent damage.
• When transporting the equipment or storing it temporarily, make sure that the surfaces
are protected from the elements and any external influences, and that they are kept dry
and clean.
2.2 Storage
The storage location must meet the following requirements:
–Dry
– Protected from unauthorized access
– Protected from harmful environmental influences such as UV light
– Temperature range: -40°C ... +85°C
– Air pressure: 58 kPa ... 106 kPa (up to 4500 m above sea level)
– Permissible humidity: 5% ... 95% (in accordance with DIN EN 61131-2)
2.3 Unpacking
The controller is supplied in packaging, together with a packing slip with installation instruc-
tions.
• Read the complete packing slip carefully before unpacking the controller.
NOTE: Electrostatic discharge
The device contains components that can be damaged or destroyed by electrostatic dis-
charge. When handling the device, observe the necessary safety precautions against
electrostatic discharge (ESD) in accordance with EN 61340-5-1 and IEC 61340-5-1.
NOTE: Property damage due to noncompliance with ESD notes
If the ESD notes are not observed during unpacking and packaging, the device may be-
come damaged.
• Observe the ESD notes during unpacking and packaging.

Transport, storage, and unpacking
107708_en_08 PHOENIX CONTACT 13 / 112
Checking the delivery • Check the delivery for transport damage.
Damaged packaging is an indicator of potential damage to the device that may have oc-
curred during transport. This could result in a malfunction.
• Submit claims for any transport damage immediately, and inform Phoenix Contact or
your supplier as well as the shipping company without delay.
• Enclose photos clearly documenting the damage to the packaging and/or delivery to-
gether with your claim.
• Immediately upon delivery, refer to the delivery note to ensure that the delivery is com-
plete.
Scope of supply for
AXC F 1152 and
AXC F 2152
– Controller AXC F 1152 or AXC F 2152
– AXL BS BK bus base module
– AXL CN S/UL supply connector
Scope of supply for
AXC F 3152
– AXC F 3152 controller
– AXC BS L 30 bus base module
– AXL CN S/UL supply connector

AXC F X152
14 / 112 PHOENIX CONTACT 107708_en_08
3 Description of the controllers
3.1 General description of the controllers
The AXC F 1152 and AXC F 2152 controllers are modular small-scale controllers. The
AXC F 3152 is a modular controller with an integrated Ethernet and Axioline F local bus con-
nection.
The controllers consist of an electronics module (1) and a bus base module (2).
Figure 3-1 Components of the controller
Axioline F station An Axioline F station is created by connecting Axioline F modules to the controller. The
Axioline F local bus (referred to as local bus in this document) is implemented by arranging
bus base modules side by side.
Inline station As an alternative to an Axioline F station, you can create a PLCnext Inline station using the
controller. To do so, you need the AXC F IL ADAPT Inline adapter terminal (Order
No. 1020304). You can directly align the Inline modules to the Inline adapter terminal.
Programming The controllers can be configured and programmed in accordance with IEC 61131 using the
PLCnext Engineer automation software.
In addition or as an alternative to the programming languages specified in IEC 61131-3, you
can also use the C++ or MATLAB®Simulink®programming languages. The individual pro-
grams or program parts can be programmed in any development environment (e.g.,
Eclipse, Microsoft®Visual Studio®, etc.). These programs or program parts must then be
imported into PLCnext Engineer as a library.
Integrated Ethernet
interfaces
The AXC F 1152 and AXC F 2152 controllers feature two switched Ethernet interfaces for
TCP/IP / UDP/IP communication within the Ethernet network.
The AXC F 3152 controller features three independent Ethernet interfaces for TCP/IP /
UDP/IP communication within the Ethernet network.
PROFINET controller/
device functionality
The PROFINET protocol can be used via the Ethernet interfaces of the controllers. In this
case, the controller can be used as a PROFINET controller or PROFINET device, depend-
ing on the configuration.
AXC F 1152 and AXC F 2152 AXC F 3152
2
1
UL
a1b1
b2b1
1
2

Description of the controllers
107708_en_08 PHOENIX CONTACT 15 / 112
Axioline F local bus There is an interface to the Axioline F local bus on the bottom of the controller. Bus base
modules are used to carry the communications voltage and the bus signals from the con-
troller through the Axioline F station. A bus base module is supplied with the controllers.
Up to 63 Axioline F modules can be connected to the controllers. The modules are con-
nected to the right of the controller. The maximum number of modules that can be operated
depends on the current consumption of the modules. The total current consumption of all
devices connected to the controller must not exceed the maximum current that the control-
ler supplies for the local bus.
Left-alignment of
Axioline F extension
modules
– You can connect one Axioline F extension module to the left of the AXC F 2152 using
the AXC BS L 2 bus base module.
– You can connect one AXC F XT IB Axioline F extension module to the left of the
AXC F 3152 using the supplied AXC BS L 30 bus base module. Connection of the left-
alignable AXC F XT ETH 1TX Ethernet interface is not supported yet.
– Axioline F extension modules cannot be aligned to the left of the AXC F 1152.
The following left-alignable Axioline F extension modules are currently available:
– AXC F XT ETH 1TX (Order No. 2403115):
Left-alignable Ethernet interface
– AXC F XT IB (Order No. 2403018):
Left-alignable INTERBUS master for the connection of up to 255 INTERBUS remote
bus devices
For additional information on how to integrate your controller as a PROFINET controller
or device, please refer to the PLCnext Engineer online help.
NOTE: Electronics may be damaged when overloaded
Observe the current consumption of each device when configuring an Axioline F station.
The current consumption is specified in each module-specific data sheet and may vary.
The possible number of devices that can be connected depends on the structure of the
Axioline F station.
Please note:
The AXC BS L 2 bus base module is not supplied with the AXC F 2152. For the ordering
data for the bus base module, please refer to Section “Ordering data” on page 91.
For the INTERBUS master, please note:
The left-alignable AXC F XT IB INTERBUS master and the AXC F IL ADAPT Inline adapt-
er terminal cannot be used simultaneously.

AXC F X152
16 / 112 PHOENIX CONTACT 107708_en_08
Axioline F/
system and firmware
For system-specific information on the Axioline F system, please refer to the
PLCnext Engineer online help and the “Axioline F: System and installation”
(UM EN AXL F SYS INST) and “Axioline F: Diagnostic registers and error messages”
(UM EN AXL F SYS DIAG) user manuals.
The user manuals can be downloaded at phoenixcontact.net/product/2404267.
MRP (only AXC F 1152 and
AXC F 2152)
The MRP (Media Redundancy Protocol) can be used via the Ethernet interfaces of the con-
troller. The controller supports the MRP client function, which can be enabled or disabled
via an engineering tool (e.g., PLCnext Engineer). This function is disabled in delivery state.
If the function is enabled, it remains enabled after the supply voltage is switched off and on.
If the controller has been reset to the delivery state, the MRP client function will also be dis-
abled again. In a ring with Media Redundancy Protocol, maximum switch-over times of up
to 200 ms can be expected.
Parameterization
memory/SD card
The controllers have an internal parameterization memory. This memory can be used to
store programs and configurations which belong to your project, e.g., the visualization proj-
ect. If the internal parameterization memory is not large enough for your application, the
controllers can be operated using an SD card. The SD card is optional and not required to
operate the controllers.
Data buffering/backup in
the event of voltage
failures
In the event of a supply voltage failure, the AXC F 3152 saves control data, e.g., retain data
and log files, on the inserted parameterization memory (SD card).
The device firmware recognizes the voltage failure. The retain data (variables of the control-
ler that are marked as “Retain” in the PLCnext Engineer project) and log files are automati-
cally backed up on the parameterization memory.
Visualization You can create visualizations for the controller using the HMI integrated in
PLCnext Engineer.
Real-time clock In the event that the supply voltage fails, the real-time clock integrated in the controllers is
buffered, see Section “Ordering data and technical data” on page 91.
Function extensions using
PLCnext apps
You can easily extend the scope of functions of the controllers using apps from the
PLCnext Store.
Visit the PLCnext Store at plcnextstore.com.
The SD card is not included in the scope of delivery of the controller.
• Only use an SD card provided by Phoenix Contact (see Section “Ordering data” on
page 91).
NOTE: Damage to the SD card after formatting
The SD card is already formatted (ext4 format) and is intended for use with
Phoenix Contact controllers of the PLCnext Control product family. If you format the SD
card, certain information on the SD card that is required for use with Phoenix Contact de-
vices will be lost. After formatting, you can no longer use the SD card to operate the con-
troller.
• Ensure that the SD card is not formatted.
NOTE: Startup of the AXC F 3152 not ensured
For proper startup of the device, the supply voltage may be switched on at the earliest 30
seconds after the diagnostic and status indicators go out.

Description of the controllers
107708_en_08 PHOENIX CONTACT 17 / 112
3.2 Licensing information regarding open-source
software
The controllers work with a Linux operating system.
License information for the individual Linux packages can be found in the file system of the
controller under:
/usr/share/common-licenses
Alternatively, you can also call up the license information via the web-based management
system of the controller, see Section 9.
Notes on LGPL software
libraries
All open-source software used in the product is subject to the respective license terms that
are not affected by the Phoenix Contact Software License Terms (SLT) for the product. In
particular, the license holder can change the respective open-source software in accor-
dance with the applicable license terms. If the license holder wishes to change an LGPL
software library contained in this product, reverse engineering is permitted for debugging
such modifications.
Notes on OpenSSL This product includes software developed by the OpenSSL Project for use in the OpenSSL
Toolkit. (http://www.openssl.org/).
This product includes cryptographic software written by Eric Young ([email protected]).
3.3 Requesting the source code
The controllers contain software components that are licensed by the rights holder as free
software or open-source software under the GNU General Public License.
You can request the source code of these software components in the form of a CD or DVD-
ROM for a processing fee of 50 euros within three years after delivery of the controller.
To do so, contact the Phoenix Contact After Sales Service in writing at the following ad-
dress:
PHOENIX CONTACT GmbH & Co. KG
After Sales Service
Flachsmarktstraße 8
32825 Blomberg
GERMANY
Subject: “Source Code AXC F 1152”, “Source Code AXC F 2152”, or
“Source Code AXC F 3152”
3.4 Directory structure of the file system
The controllers work with a Linux operating system. You can access the controller via SFTP
or via SSH and view the directories and files on the file system (on the internal parameter-
ization memory and on the optional SD card) and modify them as necessary.
Information on the directory structure of the file system can be found in Section 3.4.
Information on the directory structure of the file system can be found at the
PLCnext Technology Info Center.

AXC F X152
18 / 112 PHOENIX CONTACT 107708_en_08
3.5 Using SFTP to access the file system
The file system (on the internal parameterization memory and on the SD card of the control-
ler) is accessed via the SFTP protocol. An SFTP client software is required for this (e.g.,
WinSCP).
Access to the file system via SFTP requires authentication with a user name and password.
In the delivery state, the following access data with administrator rights is preset:
User name: admin
Password: printed on the controller (see Figure 3-2).
Figure 3-2 Administrator password on the controller
Please note:
Authentication with a user name and password is always required for SFTP access and
cannot be deactivated.
Only users with administrator rights can access the file system.
You can create additional users with administrator rights in the web-based management
system of the controller. For additional information, please refer to the
PLCnext Technology Info Center.
AXC F 1152 and AXC F 2152 AXC F 3152
SD-CARD
R
X4
MAC Addr.: 00.A0.45.9D13.BC
Ord. No. 2404267
AXC F 2152
X1
X2
UL
a1 b1
b2b1
scan here
for easy start up
BF-C
BF-C
SF
BOOT
EXT
FAIL
RUN
DBG
D
E
PLCnext Technology
Designed by PHOENIX CONTACT
password: 12345678
www.plcnext-community.net
ULUL
a1 b1
b2b1b1
X2
BF-C
BF-C
SF
BOOT
EXT
FA I L
RUN
DBG
D
E
X1
X3
SD-CARD
RUN/PROG
X4
R
STOP
MRESET
password: 12345678
plcnextcommunity.com
PLCnext Control
Ord.-No 1069208
AXC F 3152

Description of the controllers
107708_en_08 PHOENIX CONTACT 19 / 112
3.6 Firewall
3.7 Possible fields of application of the controller
3.7.1 The controller as a distributed controller of an Axioline F
station
The controller can be used as a distributed controller of an Axioline F station that is con-
nected to an Ethernet system. A maximum of 63 devices (Axioline F modules) can be con-
nected to the controller. The maximum number of alignable devices depends on the current
consumption of the devices. The total current consumption of all devices aligned on the con-
troller must not exceed the maximum current that the controller supplies for the local bus
(1 A at an ambient temperature ≤55°C). If the current consumption exceeds the maximum
current, use the AXL F PWR 1H power module.
Figure 3-3 Example: Axioline F station with AXC F 2152 controller
The firewall of the controller is deactivated by default.
Recommended:
• Activate the firewall.
For information on the firewall, please refer to the PLCnext Technology Info Center.
Ethernet

AXC F X152
20 / 112 PHOENIX CONTACT 107708_en_08
3.7.2 The controller as a PROFINET controller in a PROFINET
network
Figure 3-4 shows the example of the AXC F 3152 controller as a PROFINET controller in a
PROFINET network.
Figure 3-4 Example: AXC F 3152 controller as PROFINETcontroller
Key:
APROFINET controller (AXC F 1152, AXC F 2152 or AXC F 3152)
BPROFINET device and switch (in the example: controller with connected Axioline F I/O
modules)
UL
a1 b1
b2b1
UL
a1 b1
b2b1
UL
a1 b1
b2b1
1357
2468
MODE
ACT SPD FD
US1 US2 FAIL
LINK
Mode
12345678
X12
V.24
X9 X10
US1 GND US2 GND R1 R2
X10
MAC
Address
FL SWITCH SMSC 8GT
Ord.. No. 2891123
A
PROFINET
B
PROFINET
B
B
For additional information on how to integrate the controller as a PROFINET controller into
a PROFINET network, please refer to the PLCnext Engineer online help.