Phoenix Contact AXC F 1050 User manual

User manual
Installing, starting up, and
operating the AXC F 1050
controller

2018-10-30
PHOENIX CONTACT GmbH & Co. KG • Flachsmarktstraße 8 • 32825 Blomberg • Germany
phoenixcontact.com
107709_en_00
Installing, starting up, and operating the AXC F 1050 controller
UM EN AXC F 1050
Designation As of HW ver-
sion
As of FW version Order No.
AXC F 1050 05 4.00 2404701
User manual
This user manual is valid for:

Table of contents
107709_en_00 PHOENIX CONTACT 3 / 140
Table of contents
1 For your safety ...........................................................................................................................7
1.1 Identification of warning notes ...............................................................................7
1.2 Qualification of users .............................................................................................7
1.3 Field of application of the product..........................................................................8
1.3.1 Intended use ..........................................................................................8
1.3.2 Modifications ..........................................................................................8
1.4 Safety notes...........................................................................................................8
1.5 Notes on using the AXC F 1050 controller in potentially explosive areas.............11
2 Transport and unpacking .........................................................................................................13
2.1 Transport .............................................................................................................13
2.2 Storage................................................................................................................13
2.3 Checking the delivery ..........................................................................................13
2.4 Unpacking ...........................................................................................................14
3 Description of the AXC F 1050 .................................................................................................15
3.1 Hardware and software requirements..................................................................15
3.2 General description of the controller ....................................................................15
3.3 Possible fields of application of the controller ......................................................18
3.3.1 Controller as a decentral controller for an Axioline F station .................18
3.3.2 The AXC F 1050 as a PROFINET controller in a PROFINET
network ................................................................................................19
3.3.3 The AXC F 1050 as a PROFINET device in a PROFINET net-
work .....................................................................................................20
3.3.4 System redundancy with the AXC F 1050 ............................................21
3.4 Connection and operating elements ....................................................................23
3.5 Diagnostics and status indicators ........................................................................24
3.6 Mode selector switch...........................................................................................28
3.7 Reset button (concealed) ....................................................................................29
3.8 Parameterization memory....................................................................................30
3.9 Internal basic circuit diagram ...............................................................................31
3.10 Interfaces.............................................................................................................32
3.10.1 Ethernet ...............................................................................................33
3.10.2 Service interface (Micro-USB type B) ...................................................33
3.11 Supply plug..........................................................................................................34
3.12 Bus base module.................................................................................................34

AXC F 1050
4 / 140 PHOENIX CONTACT 107709_en_00
4 Mounting hardware ..................................................................................................................35
4.1 Safety notes.........................................................................................................35
4.2 Basics..................................................................................................................37
4.3 Structure of an Axioline F station .........................................................................39
4.4 Mounting the controller ........................................................................................40
4.5 Inserting the SD card ...........................................................................................41
5 Connecting and wiring hardware ..............................................................................................42
5.1 Safety notes.........................................................................................................42
5.2 Supply voltage.....................................................................................................44
5.2.1 Sizing of the power supply ...................................................................44
5.2.2 Connecting the power supply ...............................................................45
5.3 Connecting Ethernet............................................................................................47
6 Starting up with PC Worx Engineer ..........................................................................................48
6.1 Installing PC Worx Engineer ................................................................................48
6.2 PC Worx Engineer licenses .................................................................................48
6.3 User interface ......................................................................................................49
6.4 Creating a new project.........................................................................................51
6.5 Configuring the IP settings...................................................................................52
6.5.1 Setting the IP address range ................................................................52
6.5.2 Setting the IP address ..........................................................................53
6.6 Using the simulation function...............................................................................54
6.7 Connecting to the controller.................................................................................55
6.8 Configuring Axioline F modules ...........................................................................58
6.9 Configuring PROFINET devices ..........................................................................60
6.9.1 Adding PROFINET devices ..................................................................60
6.9.2 Assigning online devices ......................................................................61
6.9.3 Adding I/O modules .............................................................................63
6.10 Programming in accordance with IEC 61131-3....................................................65
6.10.1 Opening and creating the POU, creating variables ..............................65
6.10.2 Creating a program ..............................................................................67
6.10.3 Creating functions and function blocks .................................................68
6.11 Instantiating programs .........................................................................................72
6.12 Assigning process data .......................................................................................73
6.13 Transfer the project to the controller ....................................................................77
6.14 Creating an HMI application ................................................................................77

Table of contents
107709_en_00 PHOENIX CONTACT 5 / 140
7 Additional functions in PC Worx Engineer ................................................................................78
7.1 Entering or reading the controller functions and installation location....................79
7.2 Selecting or reading protocols for manual IP assignment ....................................80
7.3 Setting or reading the real-time clock...................................................................81
7.4 Switching the PROFINET controller / PROFINET device function on or
off ........................................................................................................................82
7.5 Using the SD card as the main memory or additional memory.............................83
7.5.1 Main memory .......................................................................................83
7.5.2 Additional memory ...............................................................................85
7.6 Activating or deactivating the MRP client function ...............................................88
7.7 Activating or deactivating the SNMP server function ...........................................89
7.8 Activating or deactivating the FTP server function ...............................................90
7.9 Activating or deactivating the SNTP client function..............................................92
8 System variables and status information ..................................................................................94
8.1 General information .............................................................................................94
8.2 Diagnostic status register ....................................................................................94
8.3 Diagnostic parameter register..............................................................................95
8.4 PROFINET system variables ...............................................................................96
8.5 IEC-61131 runtime system ..................................................................................99
8.6 Control processor ..............................................................................................101
8.7 Ethernet interfaces.............................................................................................101
8.8 SD card..............................................................................................................102
8.9 Energy storage, real-time clock .........................................................................102
8.10 Power supplies ..................................................................................................102
8.11 Mode selector switch.........................................................................................102
8.12 Project-related system variables........................................................................103
9 Web-based management (WBM) ..........................................................................................104
9.1 Establishing a connection to the WBM ..............................................................104
9.2 Changing the language......................................................................................104
9.3 Areas and functions...........................................................................................104
9.3.1 “Information” area ...............................................................................105
9.3.2 “Diagnostics” area ..............................................................................108
9.3.3 “Administration” area ..........................................................................114

AXC F 1050
6 / 140 PHOENIX CONTACT 107709_en_00
10 Removing hardware ...............................................................................................................120
10.1 Safety notes.......................................................................................................120
10.2 Removing cables...............................................................................................121
10.3 Removing the plug.............................................................................................121
10.4 Removing the SD card.......................................................................................122
10.5 Removing the controller.....................................................................................122
11 After use ................................................................................................................................123
11.1 Maintenance and servicing................................................................................123
11.2 Device replacement...........................................................................................123
11.3 Device failure and repair....................................................................................124
11.4 Disposal.............................................................................................................124
11.5 Return for disposal.............................................................................................124
12 Technical data and ordering data ...........................................................................................125
12.1 Technical data ...................................................................................................125
12.2 Ordering data.....................................................................................................129
A Technical appendix.................................................................................................................130
A 1 Performing updates ...........................................................................................130
B Appendix for document lists....................................................................................................132
B 1 List of figures .....................................................................................................132
B 2 List of tables ......................................................................................................136
B 3 Index..................................................................................................................137

For your safety
107709_en_00 PHOENIX CONTACT 7 / 140
1 For your safety
Read this user manual carefully and keep it for future reference.
1.1 Identification of warning notes
1.2 Qualification of users
The use of products described in this user manual is oriented exclusively to:
– Electrically skilled persons or persons instructed by them. The users must be familiar
with the relevant safety concepts of automation technology as well as applicable stan-
dards and other regulations.
– Qualified application programmers and software engineers. The users must be familiar
with the relevant safety concepts of automation technology as well as applicable stan-
dards and other regulations.
This symbol indicates hazards that could lead to personal injury.
There are three signal words indicating the severity of a potential injury.
DANGER
Indicates a hazard with a high risk level. If this hazardous situation is not
avoided, it will result in death or serious injury.
WARNING
Indicates a hazard with a medium risk level. If this hazardous situation is not
avoided, it could result in death or serious injury.
CAUTION
Indicates a hazard with a low risk level. If this hazardous situation is not avoided,
it could result in minor or moderate injury.
This symbol together with the NOTE signal word warns the reader of actions
that might cause property damage or a malfunction.
Here you will find additional information or detailed sources of information.

AXC F 1050
8 / 140 PHOENIX CONTACT 107709_en_00
1.3 Field of application of the product
1.3.1 Intended use
The AXC F 1050 controller is a modular small-scale controller that can be used for smaller
and medium-sized applications. The device has an IP20 protection class and is designed
for use in closed control cabinets or control boxes (junction boxes) with IP54 degree of pro-
tection or higher.
The device is designed for use in industrial environments.
1.3.2 Modifications
Modifications to hardware and firmware of the device are not permitted.
Incorrect operation or modifications to the device can endanger your safety or damage the
device. Do not repair the device yourself. If the device is defective, please contact
Phoenix Contact.
1.4 Safety notes
Observe the country-specific installation, safety, and accident prevention regulations.
During startup and maintenance work, proceed in accordance with the five safety rules of
DIN EN 50110-1. In general, the rules should be observed in the order indicated below:
– Disconnect safely
– Ensure power cannot be switched on again
– Verify safe isolation from the supply
– Ground and short circuit
– Cover or safeguard adjacent live parts
Once the work is complete, perform the above steps again in reverse order.

For your safety
107709_en_00 PHOENIX CONTACT 9 / 140
NOTE: Risk of unauthorized network access
Connecting devices to a network via Ethernet always entails the risk of unauthorized ac-
cess to the network.
Therefore, please check your application for the option of deactivating active communi-
cation channels (for instance SNMP, FTP, BootP, DCP, etc.), or setting passwords to pre-
vent third parties from accessing the controller without authorization and modifying the
system.
Because of the controller's communication interfaces, we advise against using the con-
troller in safety-critical applications without additional security appliances.
Please take additional protective measures in accordance with the IT security require-
ments and the standards applicable to your application (e.g. virtual networks (VPN) for re-
mote maintenance access, firewalls, etc.) for protection against unauthorized network
access.
On first request, you agree to release Phoenix Contact and the companies associated
with Phoenix Contact GmbH & Co. KG, Flachsmarktstraße 8, 32825 Blomberg in accor-
dance with §§ 15 ff. AktG or the German Stock Corporation Act (hereinafter collectively
referred to as “Phoenix Contact”) from all third-party claims that are made due to improper
use.
For the protection of networks for remote maintenance via VPN, Phoenix Contact offers
the mGuard product range as security appliances, which you can find described in the lat-
est Phoenix Contact catalog (phoenixcontact.net/products).
Additional measures for protection against unauthorized network access are listed in the
AH EN INDUSTRIAL SECURITY application note. The application note is available for
downloading at phoenixcontact.net/products.
NOTE: Electrostatic discharge!
The device contains components that can be damaged or destroyed by electrostatic dis-
charge. When handling the device, observe the necessary safety precautions against
electrostatic discharge (ESD) in accordance with EN 61340-5-1 and IEC 61340-5-1.
NOTE: Device failure
The device is designed to be powered by an external 24 V DC voltage supply. The per-
missible voltage range is from 19.2 V DC to 30 V DC (ripple included). If the voltage ex-
ceeds or falls below the permitted voltage range, this may lead to device failure.
•Ensure that the voltage is kept within the permitted range.
NOTE: Electrical damage due to inadequate external protection – No safe fuse
tripping in the event of an error
The electronics in the device will be damaged due to inadequate external protection.
•Protect the supply voltage externally in accordance with the connected load (number
of Axioline F devices / amount of logic current consumption for each device).
•Ensure the external fuse trips reliably in the event of an error.
NOTE: Device damage due to polarity reversal
Polarity reversal puts a strain on the electronics and can damage the device.
•To protect the device, avoid reversing the poles of the 24 V supply.

AXC F 1050
10 / 140 PHOENIX CONTACT 107709_en_00
NOTE: Device failure if operated outside the permitted ambient temperature
range
Operating the device in ambient temperatures that are not within the permitted range may
lead to malfunctions or even device failure.
•Ensure that the device is being operated within the permitted ambient temperature
range, see Section 12.1 for more information.
NOTE: Device failure
The device is designed for mounting on a DIN rail in a control cabinet. If you do not mount
the device on a DIN rail in a control cabinet, the device’s degree of protection will not be
ensured. This can lead to device failure.
•Mount the device as described in Section 4.2 and Section 4.4 in order to ensure the
device’s degree of protection.
NOTE: Device failure due to operation above the permitted specifications for vi-
brations and shock
If the device is subjected to vibrations and shock levels above the permitted specifications
during operation, this may lead to malfunctions or even device failure.
•Ensure that the permitted specifications for vibrations and shocks are adhered to
when operating the device, see Section 12.1.
NOTE: Electrical damage
Performing work on the controller during operation can damage the device electronics.
•Before working on the device, disconnect power from the controller.
•Make sure that the supply voltage cannot be switched on again by unauthorized per-
sons.
NOTE: Component breakage and/or short circuit
Inserting the device connectors (RJ45 connectors or USB connectors) into sockets for
which they were not designed can lead to components being broken and/or device short
circuit.
•Plug each connector only into the socket on the device intended for that connector.
NOTE: Property damage due to impermissible stress
The IP20 degree of protection (IEC 60529/EN 60529) requires that the device be used in
a clean and dry environment. If you use the device in an environment that is outside of the
specified limits, this may cause damage to the device.
•Do not subject the device to mechanical or thermal stress that exceeds the specified
thresholds.
Please note:
The service interface is currently without function.
The service interface (Micro-USB type B) is intended for connecting a PC. The service in-
terface is not intended for connecting other peripheral devices.

For your safety
107709_en_00 PHOENIX CONTACT 11 / 140
1.5 Notes on using the AXC F 1050 controller in
potentially explosive areas
Installation notes
1. The controller is a category 3 device and is suitable for installation in zone 2 potentially
explosive areas.
The controller meets the requirements of EN 60079-0:2012+A11:2013 and
EN 60079-15:2010.
2. The controller must be installed, started up, operated, and maintained by qualified spe-
cialist personnel only.
3. Follow the installation instructions described in this user manual, in the device-specific
packing slip, and in the UM EN AXL F SYS INST user manual.
4. When installing and operating the device, the applicable safety directives (including na-
tional safety directives), accident prevention regulations, as well as general technical
regulations must be observed.
5. For the safety data, please refer to the corresponding documentation (user manual,
packing slip) and the certificates (declaration of conformity and other approvals, if ap-
plicable).
6. Do not open up or modify the controller. Do not repair the controller yourself; instead
replace it with an approved controller of the same type.
Repairs may only be performed by the manufacturer. The manufacturer is not liable for
damage resulting from non-compliance.
7. The IP20 degree of protection (EN 60529) requires that the device be used in a clean
and dry environment.
8. Do not subject the controller to mechanical strain and/or thermal loads that exceed the
limits specified in the product documentation.
9. The controller is not designed for use in potentially dust-explosive atmospheres. If dust
is present, install the device in suitable, approved housing. Please note the surface
temperature of the housing.
10. Stop the device and immediately remove it from the potentially explosive area if it is
damaged or was subject to an impermissible load or stored incorrectly or if it malfunc-
tions.
Approval in accordance with the 2014/34/EU directive
II 3 G Ex nA IIC T4 Gc X
WARNING: Explosion hazard
Please make sure that the following notes and instructions are observed!

AXC F 1050
12 / 140 PHOENIX CONTACT 107709_en_00
Installation in zone 2
1. Observe the specified conditions for use in potentially explosive areas.
2. Install the device in a suitable approved housing (with at least IP54 protection in accor-
dance with EN 60529) that meets the requirements of EN 60079-15:2010. Pay atten-
tion to the requirements of EN 60079-14.
3. The following work is only permitted in potentially explosive areas when the power is
disconnected:
– Snapping on or disconnecting the bus base modules
– Snapping the devices onto the bus base modules and the DIN rail
– Removing the devices from the bus base modules and the DIN rail
– Connection and disconnection of cables
– Inserting and removing the SD card
4. Connect the DIN rail to protective earth ground.
5. Only devices that are designed for operation in zone 2 Ex areas and for the conditions
at the specific installation location may be connected to the circuits in zone 2.
6. The device may only be operated in potentially explosive areas when all connectors are
fully plugged in.
7. To ensure safe operation, the RJ45 connector must have a fully functioning locking clip.
Repair any damaged connectors immediately.
8. For safe operation with the SD card, it must be completely plugged and snapped in.
9. The service interface may only be used if there is no potentially explosive atmosphere.
Restrictions/limit values
1. Only connect Axioline F modules that have been approved for potentially explo-
sive areas to the controller.
Before using an Axioline F module in a zone 2 potentially explosive area, check that the
Axioline F module is approved for installation in this area. For a list of modules that are
approved for zone 2 potentially explosive areas, please refer to the
AH EN AXC/AXL F EX ZONE 2 application note.
2. Observe the restrictions/limit values specified in the product documentation for the de-
vices.
3. Make sure that the maximum permitted current consumption on the UBus is not exceed-
ed.
Refer to the “Power supply to UBus” value applicable to the controller (see section “Ax-
ioline F local bus supply (UBus)” on page 127).
4. The maximum permissible current for each spring-cage contact is 8 A.

Transport and unpacking
107709_en_00 PHOENIX CONTACT 13 / 140
2 Transport and unpacking
2.1 Transport
The device is delivered in cardboard packaging.
•Only transport the device to its destination in its original packaging.
•Please note the instructions regarding handling, moisture, shock, tilt, and temperature
indicators on the packaging.
•Observe the humidity specifications and the temperature range specified for transport
(see Section “Technical data” on page 125).
•Protect the surfaces and frame as necessary to prevent damage.
•When transporting the equipment or storing it temporarily, make sure that the surfaces
are protected from the elements and any external influences, and that they are kept dry
and clean.
2.2 Storage
The storage location must meet the following requirements:
– Dry
– Protected from unauthorized access
– Protected from harmful environmental influences such as UV light
– Temperature range: -40°C ... +85°C
– Air pressure: 58 kPa ... 106 kPa (up to 4500 m above sea level)
– Permissible humidity: 10% ... 95%, (non-condensing, non-icing)
2.3 Checking the delivery
•Check the delivery for transport damage.
Damaged packaging is an indicator of potential damage to the device that may have oc-
curred during transportation. This could result in a malfunction.
•Submit claims for any transport damage immediately, and inform Phoenix Contact or
your supplier as well as the shipping company without delay.
•Enclose photos which clearly document the damage to the packaging/delivery together
with your claim.
•Immediately after delivery, refer to the delivery note to check that the contents of the
packaging are complete.
•Keep the box and packaging material in case it is necessary to return the product.
•We strongly recommend using the original packaging to return the product.
•If the original packaging is no longer available, observe the following points:
– Observe the humidity specifications and the temperature range specified for trans-
port (see “Ambient conditions” on page 125).
– If necessary, use dehumidifying agents.
– Use appropriate ESD packaging to protect components that are sensitive to elec-
trostatic discharge.
– Make sure that the packaging you select is large enough and sufficiently thick.

AXC F 1050
14 / 140 PHOENIX CONTACT 107709_en_00
– Only use plastic bubble wrap sheets as filler material.
– Attach warnings to the transport packaging so that they are clearly visible.
– Please ensure that the delivery note is placed inside the package in the case of
packages that are to remain within the same country. However, if the package is
being sent to other countries, the delivery note must be placed inside a delivery
note pocket and attached to the outside so that it is clearly visible.
Scope of supply – AXC F 1050 controller
– AXL BS BK bus base module
– AXL CN S/UL supply plug
2.4 Unpacking
The AXC F 1050 is supplied in the packaging together with a packing slip with installation
instructions.
•Read the complete packing slip carefully before unpacking the controller.
NOTE: Electrostatic discharge!
The device contains components that can be damaged or destroyed by electrostatic dis-
charge. When handling the device, observe the necessary safety precautions against
electrostatic discharge (ESD) in accordance with EN 61340-5-1 and IEC 61340-5-1.
NOTE: Property damage due to noncompliance with ESD notes
If the ESD notes are not observed during unpacking and packaging, the device may be-
come damaged.
•Observe the ESD notes during unpacking and packaging.

Description of the AXC F 1050
107709_en_00 PHOENIX CONTACT 15 / 140
3 Description of the AXC F 1050
3.1 Hardware and software requirements
3.2 General description of the controller
The AXC F 1050 is a modular small-scale controller with integrated Ethernet and Axioline F
local bus connection.
The controller consists of an electronics module (1) and a bus base module (2).
Figure 3-1 Components of the controller
Axioline F station An Axioline F station is created by connecting Axioline F modules to the controller side-by-
side. The Axioline F local bus (referred to as local bus in this document) is implemented by
arranging bus base modules side-by-side.
Programming The controller is configured and programmed using the PC Worx Engineer automation soft-
ware. The powerful processor can be programmed in all five IEC 61131 programming lan-
guages and ensures quick control task processing.
Integrated Ethernet inter-
faces
The controller features two Ethernet interfaces for TCP/IP/UDP/IP communication within the
Ethernet network.
Hardware/software Description
Controller AXC F 1050
SD card See Section “Ordering data” on page 129
Ethernet cable Ethernet cable for connecting the controller to a PC
USB cable USB cable for connecting the controller to a PC, see Sec-
tion “Ordering data” on page 129
PC Worx Engineer ≥7.2.2
The AXC F 1050 controller is approved for use in Zone 2 potentially explosive areas.
•Observe the notes in Section “Notes on using the AXC F 1050 controller in potentially
explosive areas” on page 11.
1
2
8482B009

AXC F 1050
16 / 140 PHOENIX CONTACT 107709_en_00
PROFINET controller /
PROFINET device func-
tions
The PROFINET protocol can be used via the Ethernet interfaces of the controller. In this
case, the controller can be used as a PROFINET controller and/or PROFINET device, de-
pending on the configuration. It cannot be used as a PROFINET controller and device con-
currently.
Axioline F local bus An interface to the Axioline F local bus is provided on the bottom of the controller. Bus base
modules are used to carry the communications power and the bus signals from the control-
ler through the Axioline F station. A bus base module is supplied with the controller.
Up to 63 Axioline F modules can be connected to the controller. The maximum number of
modules that can be operated depends on the current consumption of the modules. The
total current consumption of all devices connected to the controller must not exceed the
maximum current that the controller supplies for the local bus.
Axioline F/
System and firmware
For system-specific information on the Axioline F system, please refer to the online help for
the PC Worx Engineer software and the “Axioline F: System and installation”
(UM EN AXL F SYS INST) and “Axioline F: Diagnostic registers and error messages”
(UM EN AXL F SYS DIAG) user manuals.
The user manuals can be downloaded at phoenixcontact.net/products.
MRP The MRP Media Redundancy Protocol protocol can be used via the Ethernet interfaces of
the controller. The controller supports the MRP client function, which can be enabled or dis-
abled via PC Worx Engineer (see also Section 7.6 for more information). This function is
disabled by default. If the function is enabled, it remains enabled after the supply voltage is
switched off and on. If the controller has been reset to the default settings, the MRP client
function will also be disabled again. In a ring with Media Redundancy Protocol, maximum
switch-over times of up to 200 ms can be expected.
Parameterization memory
/ SD card
The controller has an internal parameterization memory. This memory can be used to store
programs and configurations which belong to your project, e.g. the visualization project. If
the internal parameterization memory is not large enough for your application program, the
controller can be operated using an SD card. The SD card is optional and not required to
operate the controller.
For additional information on how to integrate the AXC F 1050 as a PROFINET controller
or device, please see Section 7.4.
NOTE: Electronics may be damaged if overloaded
Observe the current consumption of each device when configuring an Axioline F station.
The current consumption is specified in each module-specific data sheet and may vary.
The possible number of devices that can be connected depends on the structure of the
Axioline F.
The SD card is not included in the scope of delivery of the controller.
•Only use a parameterization memory provided by Phoenix Contact (see Section “Or-
dering data” on page 129).
NOTE: Damage to the SD card after formatting
The SD card is already formatted and is intended for use with Phoenix Contact devices.
If you format the SD card, certain information on the SD card that is required for use with
Phoenix Contact devices will be lost. After formatting, you can no longer use the SD card
to operate the controller.
•Make sure that the SD card is not reformatted.

Description of the AXC F 1050
107709_en_00 PHOENIX CONTACT 17 / 140
Visualization You can create visualizations for the controller using the PC Worx Engineer HMI.
Real-time clock In the event that the supply voltage fails, the real-time clock integrated in the controller is
buffered (see Section “Technical data” on page 125). You can query the status of the real-
time clock using system variables (see Section 8.9 for more information).

AXC F 1050
18 / 140 PHOENIX CONTACT 107709_en_00
3.3 Possible fields of application of the controller
3.3.1 Controller as a decentral controller for an Axioline F
station
The controller can be used as a decentral controller for an Axioline F station that is con-
nected to an Ethernet system. A maximum of 63 devices (Axioline F modules) can be con-
nected to the controller. The maximum number of alignable devices depends on the current
consumption of the devices. The total current consumption of all devices aligned on the con-
troller must not exceed the maximum current that the controller supplies for the local bus
(2 A).
Figure 3-2 Axioline F station with AXC F 1050 controller
D
UI
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
35
32
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
D
UA
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
3532
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
56
46
66
76
47
57
67
77
44
64
54
74
45
55
65
7572
62
52
42 43
53
63
73
40
50
60
70
41
51
61
71
Ethernet
8482B001

Description of the AXC F 1050
107709_en_00 PHOENIX CONTACT 19 / 140
3.3.2 The AXC F 1050 as a PROFINET controller in a PROFINET
network
Figure 3-3 shows the example of an AXC F 1050 as a PROFINET controller in a PROFINET
network.
Figure 3-3 AXC F 1050 as a PROFINET controller
Key:
AAXC F 1050 PROFINET controller
BPROFINET device (in the example: PROFINET bus coupler with connected Axioline F
I/O modules)
For additional information on how to integrate the AXC F 1050 into a PROFINET network
as a PROFINET controller, please refer to Section 7.4.
PROFINET
8482A020
PROFINET
A
D
UI
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
35
32
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
D
UA
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
3532
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
56
46
66
76
47
57
67
77
44
64
54
74
45
55
65
7572
62
52
42 43
53
63
73
40
50
60
70
41
51
61
71
UL
UL
B
B

AXC F 1050
20 / 140 PHOENIX CONTACT 107709_en_00
3.3.3 The AXC F 1050 as a PROFINET device in a PROFINET net-
work
Figure 3-4 shows the example of an AXC F 1050 as a PROFINET device in a PROFINET
network.
Figure 3-4 AXC F 1050 as a PROFINET device
Key:
APROFINET controller (in the example: RFC 470 PN 3TX Remote Field Controller)
BManaged Switch (in the example: FL SWITCH SMCS ...)
CAXC F 1050 PROFINET device
For additional information on how to integrate the controller into a PROFINET network as
a PROFINET device, please refer to Section 7.4.
PROFINET
A
8482B002
PROFINET C
RUN/PROG
STP
MRESET
DISPLAY
RFC 470 PN 3TX
Ord.No.2916600
+
-
LNK
LNK
LNK
USB
REMOTE
ACT
ACT
ACT
LAN1.1 LAN1.2
LAN2
I/O
24VDC
D
UI
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
35
32
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
D
UA
E1
E2
a2
b1
b2
a1
16
06
26
36
07
17
27
37
04
24
14
34
05
15
25
3532
22
12
02 03
13
23
33
00
10
20
30
01
11
21
31
56
46
66
76
47
57
67
77
44
64
54
74
45
55
65
7572
62
52
42 43
53
63
73
40
50
60
70
41
51
61
71
B
00.A0.45.06.04.02
MAC
Address
1234
LINK
Mode
US2 FAIL
X9
US1 GND US2GND
X10
R1 R2
FL SWITCH SMSC 8GT
Ord. No. 2891123
US1
X11
MEM
MODE
SPD
FD ACT
5678
X12
V.24
1357
2468