PhotoCentric AIR WASH L User manual

Air Wash L
www.photocentricgroup.com
UK - Cambridge House, Oxney Road, Peterborough, PE1 5YW. [phone]
USA - 2205 West Parkside Lane, Phoenix, 85027, AZ. [phone]
Air Wash L
PHOTOCENTRIC
AIR WASH L
INSTALLATION
GUIDE
Revision 1
06/10/2020

PHOTOCENTRIC AIR WASH L INSTALLATION GUIDE
1- Air Wash L at a glance
1 2
The tank is built in stainless steel and holds 90 l (24 US gallon) chemicals
and works with an internal air ow of 40 l/min at a pressure of 160 mbar
(2.3 psi)
Figure 1. Air Wash L
Lid
Extraction Vent
Casters
Print bed support
bracket
3
2
1
6
On/o button
5
Basket
4
Air Wash L Air Wash L
2. Suitable location
When choosing a suitable location for your Photocentric Air Wash
L, choose a at stable location with enough space for the unit (see
dimensions in Figure 2) and leave extra room over the unit to allow
opening the lid. Consider the ergonomics of operating the wash unit.
The installation location should have an operating temperature in the
range 18-28 °C. Moreover, a low-light or red lighted work environment
is recommended, as Daylight resins will cure in ambient white light.
Always avoid direct sunlight. This is especially recommended when
handling unwashed platforms and parts.
Always use Photocentric Air Wash L in a well-ventilated area and
consider vicinity to extraction duct.
To connect the Air Wash L to extraction, use a screwdriver to open the
vent on the top of the unit and fasten a 4-inch spigot, which can be linked
to the extraction duct. The spigot should be purchased separately, (as a
reference, please see https://www.blauberg.co.uk/en/metal-il-spigot-
take-o-ange.
Figure 2: Air Wash L dimensions
400 mm (15 3/4”) 620 mm (24 1/2”)
990.5 mm (39 1/4”)

4
Air Wash L
3
Air Wash L
Recommended extracton
15m3/s connected to 4 inch spigot
3- Unboxing & Placing Air Wash L
Photocentric Air Wash L is packed in a cardboard enclosure. Please do
not lift the unit, as it weighs 56 kg (124 lbs). To unbox Air Wash L, remove
the plastic packaging and remove the cardboard sleeve covering the
unit. Check that the caster brakes are inactive, carefully slide the unit
out of the cardboard base, on its casters, and place it on the desired
location. Two people are recommended for this operation. Use safety
gloves with a secure grip surface to prevent slipping.
Once satisifed with the location, press caster breakes to ensure stability
of the unit while operating.
4. Power requirements
• Photocentric Air Wash L requires a mains power supply with a
voltage of 110 VAC or 220 VAC (depending on the unit).
• Air Wash L power consumption is rated at 35-45 watts.
• Only connect Photocentric Air Wash L to the mains socket using the
power cable supplied.
• The wash unit power cable is on the right-hand side of the machine.
• Always plug the power cable into the mains socket and into the
wash unit before switching on the power at the mains socket.
• Similarly, always switch o the power at the mains socket before
unplugging the power cable from either the wash unit or the mains
socket.
• The wash unit power cable is on the right-hand side of the machine.

4
Air Wash L Air Wash L
3
[email protected]
Cambridge House, Oxney Road, Peterborough, PE1 5YW
www.photocentricgroup.com
Contact for further enquiries
NOTES