Phrozen MegaCure User manual

歡迎關注Phrozen社群獲取最新消息，並訂閱Phrozen Youtube頻道，觀看更多3D列印機教學。
如有任何疑問，請隨時發送電子郵件至 [email protected]與我們聯繫。
▎固化時間預設模式 ▎手動調整固化時間
此模式可快速選擇三種預設固化時間，分
別為10分鐘、30分鐘及60分鐘。
點擊上下鍵，每次可增減1分鐘。長按上下
鍵，則可快速增減分鐘數。
設定固化時間
02
▎機台插上電源線 ▎連接電源
將電源線插上機台。 將電源線插上插座，機台立即啟動。
若要關閉電源請移除插頭。
啟動電源
01
關上機台遮光門，按下 按鈕，固化燈即
開始運轉。
固化燈運轉
03
固化燈使用說明
▎8歲以上兒童、肢體及行為障礙者需在法定監護人的指導下使用本
產品，以確保使用者知悉所涉及的風險。禁止兒童在沒有監護人的
陪同下使用本產品。
▎未經法定監護人陪同，禁止兒童清潔或維護本產品。
如需外觀清潔請用酒精擦拭，請勿用油性或腐蝕性的液
體擦拭。
保養方式
▎固化燈需確實關上遮光門，才
能啟動固化燈。
▎請勿在未關上遮光門的情況下
直視固化燈光源，以免造成眼
部損傷。
注 意 事 項
InstagramYoutube
Facebook
社團Facebook

Please follow Phrozen’s social media accounts and subscribe to our YouTube channel to learn more about printing tips and share ideas with one another.
If you have any questions, feel free to contact us via email at [email protected].
InstagramYoutube
Facebook
Group
Facebook
Warning
▎This appliance can be used by children aged 8 and above as well as by persons
with reduced physical, sensory, or mental capabilities, if supervised or given
instruction regarding the use of the appliance in a safe way, to ensure that the
hazards involved are understood. Children are NOT allowed to play with the
appliance.
▎Children are NOT allowed to clean or provide device maintenance without adult
supervision.
▎Standard Maintenance Procedure
Please use sanitizing alcohol to clean the outside of your device. Do not use any
oily or corrosive liquids to clean the device.
UV Curing Lamp User Guide
▎Plug in the power cable ▎Connect cable to electrical outlet
Connect the power cable to the device. Once the power cable has been plugged
in, the device will turn on immediately. To
turn off the device, please plug out the
power cable.
Power Supply & Light Switch
01
▎For Preset Curing Mode ▎For Custom Curing Mode
This comes with three curing time settings:
10 min, 30 min, 60 min.
Click on the up and down keys to increase
or decrease time by 1 minute. Long press
the keys to quickly increase or decrease
the minutes.
Set Curing Time
02
Close the UV lamp cover. Click on the
Power button. The curing lamp will begin
operation.
How to Operate
the UV Curing Lamp
03
▎The UV lamp needs to be closed
completely for the device to begin
operation.
▎Do not stare at the UV curing lights
without closing the UV lamp as this may
cause damage to your eyes.