Pingi SOLIDGRIP PRO NST-16EU User manual

OPERATING INSTRUCTIONS
CHARGER
SOLIDGRIP™ PRO
WIRELESS
NST16EU
EN
concept manual_charger_EN_R4.indd 1concept manual_charger_EN_R4.indd 1 11-03-20(W11) 10:5311-03-20(W11) 10:53

BOX CONTENT
PARTS
ENEN
SAFETY
• This device should be used as described within the instructions
for use that accompany it.
• The device must be powered from a 5V USB port by using the
included USB-A to USB-C cable. Never try to connect the device
to other power sources.
• To protect against fire, electric shock or personal injury, do not
immerse cord or device in water or other liquids.
• Unplug the USB cable when cleaning.
• Children of less than three years should be kept away unless
continuously supervised.
• CAUTION - The plastic bags and packaging used to wrap this
appliance may be dangerous. To avoid the risk of suffocation,
keep these bags out of the reach of babies and children.
These bags are not toys.
Holder
1. Phone clamps
2. USB-C connector
3. LED indicator
4. Support
5. Socket
6. Fastening nut
Air vent mount
7. Clip
8. Support
9. Ball joint
Suction cup mount
10. Suction cup
11. Lever
12. Swivel knob
13. Extension knob
14. Ball joint
7.
4.
10.2. 8.
6.
1.
11.
12.
13.
14.
3.
5.
9 .
Thank you for choosing the Pingi Solidgrip™ Pro NST-16EU phone mount and
wireless charger. Please always follow the safety instructions in this manual.
Keep this instruction manual in a safe place so that it is available at all times.
This product complies with regulatory, national and European requirements.
Never try to make technical modifications to this device. We do not accept
liability for accidents or damages resulting from failure to follow these
operating and safety instructions.
TECHNICAL SPECIFICATIONS
INPUT............................................................................................................ 5V 2A/9V 1.67A
OUTPUT........................................................................................................ 5V 1.5A/9V 1.2A
CHARGING EFFICIENCY..................................................................................................±75%
OPERATING TEMPERATURE...................................................................................-20°C~45°C
Holder Suction cup
mount
Air vent
mount
USB
Cable
Operating
instructions
6.
concept manual_charger_EN_R4.indd 2concept manual_charger_EN_R4.indd 2 11-03-20(W11) 10:5311-03-20(W11) 10:53

EN
SAFETY
• This device should be used as described within the instructions
for use that accompany it.
• The device must be powered from a 5V USB port by using the
included USB-A to USB-C cable. Never try to connect the device
to other power sources.
• To protect against fire, electric shock or personal injury, do not
immerse cord or device in water or other liquids.
• Unplug the USB cable when cleaning.
• Children of less than three years should be kept away unless
continuously supervised.
• CAUTION - The plastic bags and packaging used to wrap this
appliance may be dangerous. To avoid the risk of suffocation,
keep these bags out of the reach of babies and children.
These bags are not toys.
Suction cup mount
10. Suction cup
11. Lever
12. Swivel knob
13. Extension knob
14. Ball joint
14.
Thank you for choosing the Pingi Solidgrip™ Pro NST-16EU phone mount and
wireless charger. Please always follow the safety instructions in this manual.
Keep this instruction manual in a safe place so that it is available at all times.
This product complies with regulatory, national and European requirements.
Never try to make technical modifications to this device. We do not accept
liability for accidents or damages resulting from failure to follow these
operating and safety instructions.
TECHNICAL SPECIFICATIONS
INPUT............................................................................................................ 5V 2A/9V 1.67A
OUTPUT........................................................................................................ 5V 1.5A/9V 1.2A
CHARGING EFFICIENCY..................................................................................................±75%
OPERATING TEMPERATURE...................................................................................-20°C~45°C
Operating
instructions
concept manual_charger_EN_R4.indd 3concept manual_charger_EN_R4.indd 3 11-03-20(W11) 10:5311-03-20(W11) 10:53

WHAT TO EXPECT
The Solidgrip™ Pro NST-16EU is a Qi-enabled charger and holder for smartphones.
This means that smartphones that are compatible with the Qi-standard can automatically
charge when placed in the holder. Smartphones that do not yet support Qi wireless
charging will not charge when placed on the mount. This product supports fast charging.
CABLE AND USB-CONNECTION
A USB-A to USB-C cable is provided to power the wireless charger
from a standard USB port. Make sure a free USB charge port
is available in your car. Alternatively, you can use a commonly
available 12V to 5V USB power adapter.
This product is capable of wireless fast-charging your smartphone
when connected to a fast-charging capable power supply.
Connect the Solidgrip™ Pro NST-16EU cable to a fast-charger
compatible with your phone to use wireless fast-charging.
Output depends on the power source and device (iOS 7.5 watts
wireless charging /Android 10 watts wireless charging).
POSITIONING YOUR PHONE
The position of the phone on the mount
is important and depends on the size
of the phone. The wireless charging
module in your smartphone needs to
align with its counterpart in the charger.
You can adjust the vertical position of
your phone by adjusting the phone
support. Finding the correct position
may require some trial and error.
General recommendations
Smartphones <153 mm: phone support up
Smartphones >153 mm: phone support down
OPENING AND CLOSING
The phone holder clamps will automatically close when you
place your Qi-enabled smartphone in the holder. For non-Qi
smartphones, the side buttons on the holder may be used.
The holder can also be opened with these side buttons.
Tip: thanks to the integrated capacitors, the clamps can still be
opened for a short time after shutting down your car engine.
LED INDICATOR
- RED light: standby/not charging
- BLUE light: charging
- BLINKING light: connecting
INSTALLING A MOUNT
The Solidgrip™ Pro comes with two types of mounts:
• The extendable suction cup mount is suitable for mounting
the Solidgrip Pro™ on your windshield or other smooth
surfaces. Use the lever to tighten or loosen the suction cup.
Two knobs are provided to adjust the angle of the mount and
to extend the mount.
• The air vent mount is for attaching the Solidgrip™ Pro to an
air vent.The air vent mount can be clipped onto one of the air
vents in your cabin. Use the integrated support to keep the
holder in the desired position.
* Not all air vent layouts are compatible as designs differ per car model.
Use the air vent mount at your discretion.
Unscrew the fastening nut. Push the ball into the socket and
tighten the nut again.You can loosen the nut at any time to
adjust the angle of the phone holder.
ENEN
143 mm
162.5 mm
concept manual_charger_EN_R4.indd 4concept manual_charger_EN_R4.indd 4 11-03-20(W11) 10:5311-03-20(W11) 10:53

WHAT TO EXPECT
The Solidgrip™ Pro NST-16EU is a Qi-enabled charger and holder for smartphones.
This means that smartphones that are compatible with the Qi-standard can automatically
charge when placed in the holder. Smartphones that do not yet support Qi wireless
charging will not charge when placed on the mount. This product supports fast charging.
CABLE AND USB-CONNECTION
A USB-A to USB-C cable is provided to power the wireless charger
from a standard USB port. Make sure a free USB charge port
is available in your car. Alternatively, you can use a commonly
available 12V to 5V USB power adapter.
This product is capable of wireless fast-charging your smartphone
when connected to a fast-charging capable power supply.
Connect the Solidgrip™ Pro NST-16EU cable to a fast-charger
compatible with your phone to use wireless fast-charging.
Output depends on the power source and device (iOS 7.5 watts
wireless charging /Android 10 watts wireless charging).
POSITIONING YOUR PHONE
The position of the phone on the mount
is important and depends on the size
of the phone. The wireless charging
module in your smartphone needs to
align with its counterpart in the charger.
You can adjust the vertical position of
your phone by adjusting the phone
support. Finding the correct position
may require some trial and error.
General recommendations
Smartphones <153 mm: phone support up
Smartphones >153 mm: phone support down
OPENING AND CLOSING
The phone holder clamps will automatically close when you
place your Qi-enabled smartphone in the holder. For non-Qi
smartphones, the side buttons on the holder may be used.
The holder can also be opened with these side buttons.
Tip: thanks to the integrated capacitors, the clamps can still be
opened for a short time after shutting down your car engine.
LED INDICATOR
- RED light: standby/not charging
- BLUE light: charging
- BLINKING light: connecting
INSTALLING A MOUNT
The Solidgrip™ Pro comes with two types of mounts:
• The extendable suction cup mount is suitable for mounting
the Solidgrip Pro™ on your windshield or other smooth
surfaces. Use the lever to tighten or loosen the suction cup.
Two knobs are provided to adjust the angle of the mount and
to extend the mount.
• The air vent mount is for attaching the Solidgrip™ Pro to an
air vent.The air vent mount can be clipped onto one of the air
vents in your cabin. Use the integrated support to keep the
holder in the desired position.
* Not all air vent layouts are compatible as designs differ per car model.
Use the air vent mount at your discretion.
Unscrew the fastening nut. Push the ball into the socket and
tighten the nut again.You can loosen the nut at any time to
adjust the angle of the phone holder.
EN
143 mm
162.5 mm
concept manual_charger_EN_R4.indd 5concept manual_charger_EN_R4.indd 5 11-03-20(W11) 10:5311-03-20(W11) 10:53

CHANGING THE SCREEN ORIENTATION
You can use your phone screen in portrait mode (vertical) or landscape mode (horizontal).
Slightly loosen the fastening nut and adjust the screen rotation as desired.
DISPOSAL OF THE DEVICE
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities. Contact your local government for information
regarding the collection systems available. If electrical appliances are disposed
of in landfills or dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obligated to take back your old appliance
for disposal free of charge.
LIMITED 3-YEAR WARRANTY
InnoGoods BV guarantees your device against material and fabrication faults for
three years after your initial purchase. Should material or fabrication faults be found,
InnoGoods will repair or replace the device with a similar or better-specified product.
Damage to the device due to any form of negligence, accident, lack of cleaning
and maintenance, or other use or abuse that can reasonably be considered to be in
conflict with the directions described in these instructions, does not fall under this
warranty. Furthermore, legal provisions with respect to consumer purchases apply.
In the event of a fault, we advise you to return the product together with the original
proof of purchase to the store where you bought it. When the defect in the device is
caused by anything other than material or fabrication faults, you may be charged for
examination and repair costs.
ENEN
TROUBLESHOOTING:
My phone will not charge and the indicator is red. What could be the problem?
- Check if your phone supports wireless charging (Qi).
- Your phone case might be too thick. We recommend a max. case thickness of 2 mm.
- Make sure your phone case does not contain metal or a magnet.
- The position of the phone support needs to be adjusted.
See ‘POSITIONING YOUR PHONE’
The LED indicator does not light up. What could be wrong?
- Check if the mount is connected to a working USB port.
- Are you using the original cable?
- Check the cable condition.
The device opens and closes continuously. What could be wrong?
- Many cars come with handy USB ports in the console. On rare occasions, these USB
ports do not give an uninterrupted, stable output.
- You can easily test your car mount by connecting it to your smartphone charger
at home. If you no longer notice the issue when the unit is connected to your phone
charger, use a 12V to USB adapter for your car.
COMPATIBLE DEVICES
The following devices are known to support wireless charging:
• iPhone 8 and later
• Samsung Galaxy S6 and later
• Qi-compatible Android smartphones
Fastening nut
concept manual_charger_EN_R4.indd 6concept manual_charger_EN_R4.indd 6 11-03-20(W11) 10:5311-03-20(W11) 10:53

CHANGING THE SCREEN ORIENTATION
You can use your phone screen in portrait mode (vertical) or landscape mode (horizontal).
Slightly loosen the fastening nut and adjust the screen rotation as desired.
DISPOSAL OF THE DEVICE
Do not dispose of electrical appliances as unsorted municipal waste, use
separate collection facilities. Contact your local government for information
regarding the collection systems available. If electrical appliances are disposed
of in landfills or dumps, hazardous substances can leak into the groundwater
and get into the food chain, damaging your health and well-being. When replacing old
appliances with new ones, the retailer is legally obligated to take back your old appliance
for disposal free of charge.
LIMITED 3-YEAR WARRANTY
InnoGoods BV guarantees your device against material and fabrication faults for
three years after your initial purchase. Should material or fabrication faults be found,
InnoGoods will repair or replace the device with a similar or better-specified product.
Damage to the device due to any form of negligence, accident, lack of cleaning
and maintenance, or other use or abuse that can reasonably be considered to be in
conflict with the directions described in these instructions, does not fall under this
warranty. Furthermore, legal provisions with respect to consumer purchases apply.
In the event of a fault, we advise you to return the product together with the original
proof of purchase to the store where you bought it. When the defect in the device is
caused by anything other than material or fabrication faults, you may be charged for
examination and repair costs.
EN
TROUBLESHOOTING:
My phone will not charge and the indicator is red. What could be the problem?
- Check if your phone supports wireless charging (Qi).
- Your phone case might be too thick. We recommend a max. case thickness of 2 mm.
- Make sure your phone case does not contain metal or a magnet.
- The position of the phone support needs to be adjusted.
See ‘POSITIONING YOUR PHONE’
The LED indicator does not light up. What could be wrong?
- Check if the mount is connected to a working USB port.
- Are you using the original cable?
- Check the cable condition.
The device opens and closes continuously. What could be wrong?
- Many cars come with handy USB ports in the console. On rare occasions, these USB
ports do not give an uninterrupted, stable output.
- You can easily test your car mount by connecting it to your smartphone charger
at home. If you no longer notice the issue when the unit is connected to your phone
charger, use a 12V to USB adapter for your car.
COMPATIBLE DEVICES
The following devices are known to support wireless charging:
• iPhone 8 and later
• Samsung Galaxy S6 and later
• Qi-compatible Android smartphones
concept manual_charger_EN_R4.indd 7concept manual_charger_EN_R4.indd 7 11-03-20(W11) 10:5311-03-20(W11) 10:53

CONTACT/SERVICE:
InnoGoods BV
The Netherlands
Rivium 2e str. 40
NL-2909 LG Capelle a/d IJssel
[phone]
[phone]
www.pingi.com
concept manual_charger_EN_R4.indd 8concept manual_charger_EN_R4.indd 8 11-03-20(W11) 10:5311-03-20(W11) 10:53