Pixsys PC800 User manual

Panel PC
Panel PC touch screen resistivi
Resistive touch screen Panel PCs
User manual / Manuale d’uso
PC800 - PC815 - PC820 - PC830

Table of contents
1 Introduction .................................................................................................................................................................. 4
2 Safety guidelines.......................................................................................................................................................... 4
2.1 Policies and procedures.............................................................................................................................. 4
2.2 Installation guidelines................................................................................................................................. 4
2.3 Viruses and dangerous programs ............................................................................................................ 4
2.4 Organization of safety notices.................................................................................................................. 5
3 Spacing for air circulation and ventilation............................................................................................................ 5
4 Environmental specifications and Approval......................................................................................................... 5
5 Device installation ....................................................................................................................................................... 5
6 Power supply and grounding.................................................................................................................................... 6
7 Wiring connections ..................................................................................................................................................... 6
8 Technical data............................................................................................................................................................... 7
8.1 Main features ................................................................................................................................................ 7
8.2 Hardware features ....................................................................................................................................... 7
8.3 UPS................................................................................................................................................................... 7
8.4 Assisted shutdown and UPS....................................................................................................................... 7
8.5 Touch Screen Display .................................................................................................................................. 8
9 Communication interfaces........................................................................................................................................ 8
9.1 USB interface ................................................................................................................................................. 8
9.2 Ethernet interface......................................................................................................................................... 8
9.3 HDMI port....................................................................................................................................................... 9
9.4 RS485............................................................................................................................................................... 9
10 Battery ............................................................................................................................................................................ 9
10.1 Internal battery replacement.................................................................................................................... 9
10.2 Battery detail................................................................................................................................................. 9
Indice degli argomenti
1 Introduzione................................................................................................................................................................ 11
2 Norme di sicurezza .................................................................................................................................................... 11
2.1 Regolamenti e procedure......................................................................................................................... 11
2.2 Linee guida per l’installazione ................................................................................................................ 11
2.3 Virus e programmi pericolosi .................................................................................................................. 12
2.4 Organizzazione delle note di sicurezza................................................................................................ 12
3 Spazi per la circolazione dell’aria e la ventilazione ........................................................................................... 12
4 Specifiche ambientali e di funzionamento.......................................................................................................... 12
5 Installazione del dispositivo.................................................................................................................................... 12
6 Alimentazione e messa a terra dello strumento................................................................................................. 13
7 Collegamenti elettrici................................................................................................................................................ 14
8 Dati tecnici................................................................................................................................................................... 14
8.1 Caratteristiche generali ............................................................................................................................ 14
8.2 Caratteristiche hardware ......................................................................................................................... 14
8.3 UPS................................................................................................................................................................. 14
8.4 Funzionamento Shutdown assistito e UPS .......................................................................................... 15
8.5 Display touch screen ................................................................................................................................. 15
9 Interfaccia di comunicazione.................................................................................................................................. 15
9.1 Interfaccia USB............................................................................................................................................ 15
9.2 Interfaccia Ethernet ................................................................................................................................... 16
9.3 Porta HDMI .................................................................................................................................................. 16
9.4 RS485............................................................................................................................................................. 16
10 Batteria......................................................................................................................................................................... 16
10.1 Sostituzione batteria tampone interna................................................................................................ 16
10.2 Dettagli della batteria............................................................................................................................... 17

4 - Panel PC - User manual
1 Introduction
Pixsys Panel Pc range features a robust metal and aluminium mechanical structure that makes them
suitable for installation in industrial environments for all visualisation/supervision applications, as a
complement to Pixsys or third party control devices.
Available in four widescreen formats, the panels have a reduced depth to optimise the space inside
the control cabinet and a linear design that integrates into the most diverse application contexts.
The dual Ethernet port combined with Pixsys Portal VPN software service extends connectivity by also
allowing access to the plant sub-network (passthrough).
2 Safety guidelines
Programmable logic controllers (PLCs), operating/monitoring devices (industrial PCs, HMI) have
been designed, developed and manufactured for conventional use in industrial environments. They
were not designed, developed and manufactured for any use involving serious risks or hazards that
could lead to death, injury, serious physical damage or loss of any kind without the implementation
of exceptionally stringent safety precautions. In particular, such risks and hazards include the use of
these devices to monitor nuclear reactions in nuclear power plants, their use in flight control or flight
safety systems as well as in the control of mass transportation systems, medical life support systems
or weapons systems.
2.1 Policies and procedures
Electronic devices are never completely failsafe. If the programmable control system, operating/
monitoring device or power supply fails, the user is responsible for ensuring that other connected
devices, e.g. motors, are brought to a secure state.
When using programmable logic controllers or operating/monitoring devices as control systems
together with a soft PLC, safety precautions relevant to industrial control systems must be observed
in accordance with applicable national and international regulations. The same applies for all other
devices connected to the system, such as drives.
All tasks such as the installation, commissioning and servicing of devices are only permitted to be
carried out by qualified personnel. Qualified personnel are those familiar with the transport, mounting,
installation, commissioning and operation of devices who also have the appropriate qualifications
(e.g. IEC 60364). National accident prevention regulations must be observed.
The safety notices, information on connection conditions (type plate and documentation) and limit
values specified in the technical data are to be read carefully before installation and commissioning
and must always be observed.
2.2 Installation guidelines
• These devices are not ready for use upon delivery and must be installed and wired according to the
specifications in this documentation in order for the EMC limit values to apply.
• Installation must be performed according to this documentation using suitable equipment and
tools.
• Devices are only permitted to be installed by qualified personnel without voltage applied. Before
installation, voltage to the control cabinet must be switched off and prevented from being switched
on again.
• General safety guidelines and national accident prevention regulations must be observed.
• Electrical installation must be carried out in accordance with applicable guidelines (e.g. line cross
sections, fuses, protective ground connections).
2.3 Viruses and dangerous programs
This system is subject to potential risks each time data is exchanged or software is installed from a data
medium (e.g. CD-ROM or USB flash-disk), a network connection or the Internet. The user is responsible
for assessing these dangers, adopting anti-virus protection systems, firewalls, etc. not supplied (unless
otherwise stated) and ensuring that software packages are exclusively from Pixsys.
Table of contents

User manual - Panel PC - 5
2.4 Organization of safety notices
Safety notices in this manual are organized as follows:
Safety notice Description
Danger! Disregarding these safety guidelines and notices can be life-threatening.
Warning! Disregarding these safety guidelines and notices can result in severe injury or
substantial damage to property.
Caution! Disregarding these safety guidelines and notices can result in injury or damage to
property.
Information! This information is important for preventing errors.
3 Spacing for air circulation and ventilation
In order to guarantee sufficient air circulation, allow 5cm of empty space above, below, to the side
and behind the device. No other ventilation system is required. The HMI device is self-ventilated and
approved for inclined mounting at angles up to ±35°in stationary cabinets.
Information! If additional space is needed to operate or maintain the device, this must be taken into
consideration during installation.
Caution! The spacing specifications for air circulation are based on the worst-case scenario for
operation at the maximum specified ambient temperature. The maximum specified ambient
temperature must not be exceeded!
Caution! An inclined installation reduces the convection by the HMI device and therefore the
maximum permissible ambient temperature for operation.
4 Environmental specifications and Approval
Operating temperature 0° C / 50° C
Storage temperature -20° C / 65° C
Relative humidity 10 / 90% non condensing
CE YES on rear panel
UL certification NO
RoHS compliant YES
5 Device installation
The device panel is installed in the cutout using provided plastic hooks. The number of provided
plastic hooks depends on the panel. The thickness of the wall or cabinet plate must be between 1 mm
and 8 mm. An ISO 7045 (ex UNI 7687 DIN 7985A) Phillips screwdriver is needed to tighten and loosen
the screws on the retaining clips. The maximum tightening torque for the retaining clips is 0,5 Nm.
Devices must be installed on a flat, clean and burr-free surface; uneven areas can cause damage to
the display when the screws are tightened or the intrusion of dust and water (as per figures 1 and 2).
Cut-out Fig. 1 Fig. 2
Lc +2 mm
Hc +2 mm

6 - Panel PC - User manual
Dimensions
Suggested
thickness/
Spessore
suggerito
0÷8 mm
+24V
1
20V
ETH2 ETH1
USB 1
M1
LW
Wc
Hc
H
Lc
D
Models D L H W * Wc * Lc Hc
PC800 8” 210 166 38 32 198 154
PC815 10,1” 268 191 43 35 256 178
PC820 12,1” 317 220 43 35 302 206
PC830 15,6” 408 257 53 45 393 242
* Dimensions refer only to the product without the size of terminals and cables.
6 Power supply and grounding
Danger! This device is only permitted to by supplied by a SELV /
PELV (class 2) power supply or with safety extra-low voltage (SELV)
in accordance with EN 60950.
Connect a 24VDC 2,5A (min.) power supply, as showed in the figure.
Connect the device grounding with a conductor of 18AWG
(2,5mmq) minimum section. For the whole series it is suggested to
use a 24 VDC 2,5A 60VA power supply (Pixsys code 2700.10.012).
Use Copper, Copper-Clad Aluminium or Aluminium conductors wire
for all electric connection.
Caution! 24 VDC power supply line must be protected by a 2,5A fuse.
Caution! Functional ground must be kept as short as possible and connected to the largest possible
wire cross section at the central grounding point (e.g. the control cabinet or system).
7 Wiring connections
This device has been designed and manufactured in conformity to Low Voltage Directive 2006/95/EC,
2014/35/EU (LVD) and EMC Directive 2004/108/EC, 2014/30/EU (EMC). For installation into industrial
environments please observe following safety guidelines:
• Separate control lines form power wires;
• Avoid proximity of remote control switches, electromagnetic contactors, powerful engines and use
specific filters;
• Avoid proximity of power groups, especially those with phase control;
• It is strongly recommended to install adequate mains filter on power supply of the machine where

User manual - Panel PC - 7
the controller is installed. The controller is designed and conceived to be incorporated into other
machines, therefore CE marking on the controller does not exempt the manufacturer of machines
from safety and conformity requirements applying to the machine itself.
8 Technical data
8.1 Main features
PC800 PC815 PC820 PC830
Power supply voltage 24 VDC ± 10%
Consumption 28,5VA 30VA 33VA 36VA
8.2 Hardware features
CPU Intel® Celeron® J1900 Quad Core @2.0GHz, 2M Cache
Intel® Celeron® N2930 Quad Core @1.83GHz, 2M Cache
RAM 4 / 8GB DDR3 / LPDDR3 1066MHz
SSD 128 / 256GB
Operating system Windows® 10 IoT LTSB Enterprise 64bit / Optional Windows® 10 Pro
64bit
The above hardware features vary depending on the model purchased.
8.3 UPS
Type Solid state capacitor UPS
Load time
The correct UPS functioning will take approx. 5 min. from the power on.
Autonomy
The UPS, in case of power failure, starts immediatly to close all
applications (which must be able to close in max. 10 Sec) and the
correct system switch off.
The use of third-party applications can lengthen the shutdown
time of the entire system, make sure that the UPS has sufficient
autonomy to ensure that it shuts down correctly, otherwise the
files in use may be lost and/or critical operating system files may
be corrupted.
Features
At the end of the shutdown the UPS emits a short beep to signal
that the system shutdown is complete. If power has returned in the
meantime, the system will restart automatically.
8.4 Assisted shutdown and UPS
0 V
24 V
V imput
Alimentazione 24 VDC
Power failure < 50 mSec
Interruzione dell’alimentazione < 50 mSec
Power failure > 50 mSec
Interruzione dell’alimentazione > 50 mSec
START SHUTDOWN
The UPS module grants an assisted system shutdown in case of power failure longer than 50mSec.
When shutdown is completed and power supply is restored, UPS module switches on the system.

8 - Panel PC - User manual
8.5 Touch Screen Display
PC800 PC815 PC820 PC830
Touch technology Resistive
Resolution 8” TFT 4:3
1024 x 768
10,1” TFT 16:10
1280 x 800
12,1” TFT 16:10
1280 x 800
15,6” TFT 16:9
1366 x 768
Colors 16M colors / 24bit
Back-lighting 320 cd/m2 400 cd/m2 400 cd/m2 300 cd/m2
Back-lighting duration* 20000 h Typ
@ 25°C**
30000 h Typ
@ 25°C**
50000 h Typ
@ 25°C**
50000 h Typ
@ 25°C**
Lifetime** 710 17 17
* Brightness reduction to 80% of default setting / ** Functioning years per 8 hours / day
9 Communication interfaces
All Panel PC devices are equipped with two
Ethernet ports, one USB 2.0 port and one USB 3.0
port
9.1 USB interface
Panel PCs have one USB 3.0 (Universal Serial Bus) port and one USB 2.0 port available on the back of
the panel.
Warning! Peripheral USB devices can be connected to the USB interfaces on this device. Due to the
large number of USB devices available on the market, Pixsys cannot guarantee their performance.
Caution! Because this interface is designed according to general PC specifications, extreme care
should be exercised with regard to EMC, cable routing, etc.
USB ports USB1 USB2
Type USB 3.0 USB 2.0
Design Type A Type A
Current-carrying capacity Max. 0,6 A Max. 0,6 A
Cable length Max. 3 m (without hub) Max. 3 m (without hub)
9.2 Ethernet interface
Panel PCs have two Ethernet ports available on the back of the panel.
Ethernet interface (ETH) ETH1 ETH2
Controller Intel®i210 AX 88179
Cabling S/STP (Cat 5e)
Transfer rate 10/100 Mbit/s ETH1-ETH2 to CPU Link
10/100/Mbit/s ETH1-ETH2 link 1Gbit/s
LED
Green (link) On = 10/100 Mbit connection
Yellow (activity) On = Activity (data transfer)

User manual - Panel PC - 9
9.3 HDMI port
Video output HDMI port,
max resolution 1920 x 1080.
9.4 RS485
Tolleranza: +/- 0.2 mm
CLIENTE
DESCRIZIONE
DESIGN
1900.10.315-EV2.CDR
Anselmi
Materiali: Poliestere goffrato spessore 150 um
Biadesivo 3M GPT-020 200 um
REV. COD.
FILE
1900.10.315
Poliestere 3
19/01/2024
ETICHETTA POSTERIORE
MASK POST TD 2ETH 1HDMI 2USB
45,5
34,6
95,0
3,6
Poliestere 150um
Biadesivo 3M GPT-020 200 um
ETH2 ETH1
USB 1
M1HDMI1
RS485 COM4
B+
A-
C
B+
A-
+24V1
2
3
4
5
6
7
0V
RS485 COM1
1234567
PANTONE BLACK 6 C
PANTONE 429 C
USB 2
Use of RS485 / COM4 on M1 terminal
PIN3: B+
PIN4: A-
PIN5: GND
Use of RS485 / COM1 on M1 terminal
PIN5: GND
PIN6: B+
PIN7: A-
10 Battery
10.1 Internal battery replacement
BIOS and clock store data also in case of power failure thanks to
a CR2032 battery placed on rear.
To replace the battery it is necessary to remove the rear panel.
10.2 Battery detail
Classification Lithium Coin
Chemical System Lithium / Manganese Dioxide (Li/MnO2)
Nominal Voltage 3.0 Volts
Typical Capacity 235 mAh (to 2.0 volts)
Typical (Li) Content 0.109 grams (0.0038 oz.)
Energy Density 198 milliwatt hr/g, 653 milliwatt hr/cc
Operating Temp -30C to 60C
Warning! CR2032 is a
“Lithium Coin” battery
Danger! KEEP OUT OF REACH OF CHILDREN. Swallowing may lead to serious injury or death in as little
as 2 hours due to chemical burns and potential perforation of the esophagus. To prevent children
from removing batteries, battery compartments is designed to be opened with a screwdriver and
is protected by a security label.
Warning! It is suggested to replace the battery every 3 years. When the battery is removed, an
internal dedicated device allows replacement without data loss if operation is completed within 1
hour since battery removal.

10 - Panel PC - User manual
Warranty terms
Pixsys srl warrants its electronic devices for 12 months from Invoice date. Pixsys liability shall be limited
to repairing (or replacing at its option) any defective product which is returned with RMA (Return
Material Authorization) priorly obtained on Pixsys website and to be clearly marked on documents.
Pixsys shall not be responsible for accident, neglect, misuse, damage to objects or people caused
using the devices outside their specifications or outside any published performance data, including
unauthorized and unqualified repairing or failure to provide proper environmental conditions. In
no event shall Pixsys liability exceed the purchase price of the product(s). Warranty does not cover
any damage arising from post-sale installation of software applications and specifically any damage
caused by malware. Technical assistance by Pixsys which should be required to restore OS will be
subject to assistance fee prevailing at time of request
Notes / Updates