Pixsys HMI series User manual

HMI series
HMI TOUCH SCREEN
410-710-810-820-830
Quick start guide - Guida breve all’installazione
12”
10”
7”
4,3”

Table of contents
1 Safety guidelines.......................................................................................................................................................... 5
1.1 Policies and procedures.............................................................................................................................. 5
1.2 Installation guidelines................................................................................................................................. 5
1.3 Viruses and dangerous programs............................................................................................................ 5
1.4 Organization of safety notices.................................................................................................................. 6
2 Spacing for air circulation and ventilation............................................................................................................ 6
3 Device installation ....................................................................................................................................................... 6
4 Power supply and grounding.................................................................................................................................... 7
5 Wiring connections ..................................................................................................................................................... 8
6 Technical data............................................................................................................................................................... 8
6.1 Main features ................................................................................................................................................ 8
6.2 Hardware features ....................................................................................................................................... 8
6.3 Touch LCD: 4 wires resistive........................................................................................................................ 8
7 Communication interfaces........................................................................................................................................ 8
7.1 CANo pen ........................................................................................................................................................ 9
7.1.a Using CAN / EXP1 on terminal M1 (Not available for -EL versions) ....................................... 9
7.2 RS232 ............................................................................................................................................................... 9
7.2.a Using RS232 / COM1 on DB9 (Not available for TD410 and -EL versions)............................ 9
7.3 RS4 85 ............................................................................................................................................................... 9
7.3.a Using RS485 / COM2 on terminal M1 ........................................................................................... 9
7.3.b Using RS485 / COM2* MASTER on DB9 (Not available for TD410 and -EL versions)....... 10
7.3.c Using RS485 / COM2 SLAVE on DB9 (Not available for TD410 and -EL versions)............. 10
7.4 USB interfaces.............................................................................................................................................. 10
8 Ethernet interface ...................................................................................................................................................... 11
8.1 Technical data............................................................................................................................................. 11
9 Internal ethernet Switch (only TD810-TD820-TD830) ....................................................................................... 11
10 Battery .......................................................................................................................................................................... 11
10.1 Internal battery replacement.................................................................................................................. 11
10.2 Battery detail............................................................................................................................................... 12
11 TdControlPanel........................................................................................................................................................... 12
11.a WIN EXPLORER...................................................................................................................................................... 13
11.b HMI_MOVICON .................................................................................................................................................... 13
11.c PLC LOGICLAB ....................................................................................................................................................... 13
11.d LAN ETH1................................................................................................................................................................ 13
11.e BACKLIGHT - BUZZER .......................................................................................................................................... 14
11.f WINVNC.................................................................................................................................................................. 14
11.g BACKUP-RESTORE................................................................................................................................................ 14
12 LogicLab Suite............................................................................................................................................................. 16
12.a Language modification...................................................................................................................................... 16
12.b Create - load a project ........................................................................................................................................ 17
12.c Connection to target........................................................................................................................................... 17
12.d Compiling and downloading the code........................................................................................................... 18
12.e Watch window...................................................................................................................................................... 18
13 Interfacing Movicon 11 with LogicLab.................................................................................................................. 19
13.a Creating a new Movicon project ...................................................................................................................... 19
13.b Driver configuration............................................................................................................................................20
13.c Downloading the Movicon code to the target ............................................................................................. 21
14 Simulation of the whole project SoftPLC + SCADA............................................................................................ 21
Indice degli argomenti
1 Norme di sicurezza .................................................................................................................................................... 24
1.1 Regolamenti e procedure......................................................................................................................... 24
1.2 Linee guida per l’installazione ................................................................................................................ 24
1.3 Virus e programmi pericolosi ..................................................................................................................24

1.4 Organizzazione delle note di sicurezza ................................................................................................25
2 Spazi per la circolazione dell’aria e la ventilazione...........................................................................................25
3 Installazione del dispositivo....................................................................................................................................25
4 Alimentazione e messa a terra dello strumento.................................................................................................26
5 Collegamenti elettrici................................................................................................................................................27
6 Dati tecnici................................................................................................................................................................... 27
6.1 Caratteristiche generali ............................................................................................................................27
6.2 Caratteristiche hardware ......................................................................................................................... 27
6.3 LCD touch: 4 fili resistivo...........................................................................................................................27
7 Interfacce di comunicazione...................................................................................................................................28
7.1 CANo pen ......................................................................................................................................................28
7.1.a Utilizzo CAN / EXP1 su morsetto M1 (Non disponibile su versioni -EL)...............................28
7.2 RS232 .............................................................................................................................................................28
7.2.a Utilizzo RS232 / COM1 su DB9 (Non disponibile per TD410 e versioni -EL)........................28
7.3 RS4 85 .............................................................................................................................................................29
7.3.a Utilizzo RS485 / COM2 su morsetto M1......................................................................................29
7.3.b Utilizzo RS485 / COM2* MASTER su DB9 (Non disponibile per TD410 e versioni -EL).....29
7.3.c Utilizzo RS485 / COM2 SLAVE su DB9 (Non disponibile per TD410 e versioni -EL)...........29
7.4 Interfaccia USB............................................................................................................................................30
8 Interfaccia Ethernet...................................................................................................................................................30
8.1 Dati tecnici ...................................................................................................................................................30
9 Switch ethernet interno (solo TD810-TD820-TD830).........................................................................................30
10 Batteria......................................................................................................................................................................... 31
10.1 Sostituzione batteria tampone interna ................................................................................................ 31
10.2 Dettagli della batteria............................................................................................................................... 31
11 TdControlPanel........................................................................................................................................................... 31
11.a WIN EXPLORER...................................................................................................................................................... 32
11.b HMI_MOVICON ....................................................................................................................................................32
11.c PLC LOGICLAB ....................................................................................................................................................... 32
11.d LAN ETH1................................................................................................................................................................ 33
11.e BACKLIGHT - BUZZER ..........................................................................................................................................33
11.f WINVNC.................................................................................................................................................................. 33
11.g BACKUP-RESTORE................................................................................................................................................ 33
12 Suite LogicLab.............................................................................................................................................................36
12.a Cambio lingua ......................................................................................................................................................36
12.b Creazione - caricamento di un progetto........................................................................................................36
12.c Collegamento al target ...................................................................................................................................... 37
12.d Compilazione e scaricamento del codice....................................................................................................... 37
12.e La watch window.................................................................................................................................................38
13 Interfacciare Movicon 11 con LogicLab ................................................................................................................38
13.a Creazione di un nuovo progetto Movicon.....................................................................................................38
13.b Configurazione del Driver..................................................................................................................................39
13.c Trasferimento del codice Movicon nel target................................................................................................40
14 Simulazione dell’intero progetto SoftPLC + SCADA.......................................................................................... 41

User manual - HMI Series - 5
1 Safety guidelines
Programmable logic controllers (PLCs), operating/monitoring devices (industrial PCs, HMI) have
been designed, developed and manufactured for conventional use in industrial environments. They
were not designed, developed and manufactured for any use involving serious risks or hazards that
could lead to death, injury, serious physical damage or loss of any kind without the implementation
of exceptionally stringent safety precautions. In particular, such risks and hazards include the use of
these devices to monitor nuclear reactions in nuclear power plants, their use in flight control or flight
safety systems as well as in the control of mass transportation systems, medical life support systems
or weapons systems.
1.1 Policies and procedures
Electronic devices are never completely failsafe. If the programmable control system, operating/
monitoring device or power supply fails, the user is responsible for ensuring that other connected
devices, e.g. motors, are brought to a secure state.
When using programmable logic controllers or operating/monitoring devices as control systems
together with a soft PLC, safety precautions relevant to industrial control systems must be observed
in accordance with applicable national and international regulations. The same applies for all other
devices connected to the system, such as drives.
All tasks such as the installation, commissioning and servicing of devices are only permitted to be
carried out by qualified personnel. Qualified personnel are those familiar with the transport, mounting,
installation, commissioning and operation of devices who also have the appropriate qualifications
(e.g. IEC 60364). National accident prevention regulations must be observed.
The safety notices, information on connection conditions (type plate and documentation) and limit
values specified in the technical data are to be read carefully before installation and commissioning
and must always be observed.
1.2 Installation guidelines
• These devices are not ready for use upon delivery and must be installed and wired according to the
specifications in this documentation in order for the EMC limit values to apply.
•
Installation must be performed according to this documentation using suitable equipment and tools.
• Devices are only permitted to be installed by qualified personnel without voltage applied. Before
installation, voltage to the control cabinet must be switched off and prevented from being switched
on again.
• General safety guidelines and national accident prevention regulations must be observed.
• Electrical installation must be carried out in accordance with applicable guidelines (e.g. line cross
sections, fuses, protective ground connections).
1.3 Viruses and dangerous programs
This system is subject to potential risk each time data is exchanged or software is installed from a data
medium (e.g. diskette, CD-ROM, USB flash drive, etc.), a network connection or the Internet. The user is
responsible for assessing these dangers, implementing preventive measures such as virus protection
programs, firewalls, etc. and making sure that software is only obtained from trusted sources.
Table of contents

6 - HMI Series - User manual
1.4 Organization of safety notices
Safety notices in this manual are organized as follows:
Safety notice Description
Danger! Disregarding these safety guidelines and notices can be life-threatening.
Warning! Disregarding these safety guidelines and notices can result in severe injury or
substantial damage to property.
Caution! Disregarding these safety guidelines and notices can result in injury or damage to
property.
Information! This information is important for preventing errors.
2 Spacing for air circulation and ventilation
In order to guarantee sufficient air circulation, allow 5cm of empty space above, below, to the side
and behind the device. No other ventilation system is required. The HMI device is self-ventilated and
approved for inclined mounting at angles up to ±35°in stationary cabinets.
Information! If additional space is needed to operate or maintain the device, this must be taken into
consideration during installation.
Caution! The spacing specifications for air circulation are based on the worst-case scenario for
operation at the maximum specified ambient temperature. The maximum specified ambient
temperature must not be exceeded!
Caution! An inclined installation reduces the convection by the HMI device and therefore the
maximum permissible ambient temperature for operation.
3 Device installation
The device panel is installed in the cutout using provided plastic hooks. The number of provided
plastic hooks depends on the panel. The thickness of the wall or cabinet plate must be between 1 mm
and 5 mm. An ISO 7045 (ex UNI 7687 DIN 7985A) Phillips screwdriver is needed to tighten and loosen
the screws on the retaining clips. The maximum tightening torque for the retaining clips is 0,5 Nm.
Devices must be installed on a flat, clean and burr-free surface; uneven areas can cause damage to
the display when the screws are tightened or the intrusion of dust and water. (as per figures 1 and 2)
Cut-out Fig. 1 Fig. 2
Lc (± 0,5 mm)
Hc (± 0,5 mm)

User manual - HMI Series - 7
Dimensions
Suggested thickness
Spessore suggerito
2 ÷ 8 mm
Suggested thickness
Spessore suggerito
2 ÷ 8 mm
TDXXX
LW
Wc
Hc
H
Lc
Suggested thickness
Spessore suggerito
2÷8 mm
Models L H W * Wc * Lc Hc
TD410-AD 140 100 36 30 130 89
TD710-AD 204 160 41 35 181 144
TD810-AD 274 216 40 31 260 200
TD820-AD 317 256 42 33 302 242
TD830-AD 406 270 50 41 391 255
* Dimensions refer only to the product without the size of terminals and cables.
4 Power supply and grounding
Danger! This device is only permitted to by supplied by a SELV /
PELV (class 2) power supply or with safety extra-low voltage (SELV)
in accordance with EN 60950.
Connect a 24VDC 1,0A (min.) power supply, as showed into the
figure. Connect the device grounding with a conductor of 18AWG
(2,5mmq) minimum section. For the whole series it is suggested to
use a 24 VDC 1,0A 24VA power supply (Pixsys code 2700.10.008).
Use Copper, Copper-Clad Aluminium or Aluminium conductors wire
for all electric connection.
Caution!
24VDC power supply line must be protected by a 1,0A fuse.
Caution! Functional ground must be kept as short as possible and
connected to the largest possible wire cross section at the central
grounding point (e.g. the control cabinet or system).

8 - HMI Series - User manual
5 Wiring connections
This device has been designed and manufactured in conformity to Low Voltage Directive 2006/95/EC,
2014/35/EU (LVD) and EMC Directive 2004/108/EC, 2014/30/EU (EMC). For installation into industrial
environments please observe following safety guidelines:
• Separate control lines form power wires;
• Avoid proximity of remote control switches, electromagnetic contactors, powerful engines and use
specific filters;
• Avoid proximity of power groups, especially those with phase control;
•
It is strongly recommended to install adequate mains filter on power supply of the machine where
the controller is installed, particularly if supplied 230 VAC. The controller is designed and conceived
to be incorporated into other machines, therefore CE marking on the controller does not exempt the
manufacturer of machines from safety and conformity requirements applying to the machine itself.
6 Technical data
6.1 Main features
TD410 * TD710 ** TD810 TD820 TD830-AD
Power supply voltage 12 ÷ 24 VDC ± 10%
Consumption (typical
use with 2 USB devices) 7.5VA 13VA 16VA 15VA 20VA
Temperature range 0...50°C
Humidity range 10...90% (without condensation)
* entry level (-EL) model available without USB, DB9 connectors (RS232 / RS485), CAN and Ethernet ports.
** entry level (-EL) model available without USB, DB9 connectors (RS232 / RS485) and CAN port.
6.2 Hardware features
CPU ARM® CORTEX™ - A8 @1.0GHz
RAM 512 MB DDR3
eMMC 4GB
6.3 Touch LCD: 4 wires resistive
TD410-AD TD710-AD TD810-AD TD820-AD TD830-AD
Resolution 4.3” TFT
480 x 272
7” TFT
800 x 480
10” TFT
800 x 600
12” TFT
1280 x 800
15,6” TFT
1366 x 768
Colors 65K (16 bit) 65K (16 bit) 65K (16 bit) 65K (16 bit) 65K (16 bit)
Back-lighting LED 400 cd/m2 LED 280 cd/m2 LED 320 cd/m2 LED 220 cd/m2 LED 300 cd/m2
Back-lighting
duration* 50000 h Typ @ 25°C** 30000 h Typ @ 25°C** 50000 h Typ @
25°C**
Lifetime** 17 10 17
* Brightness reduction to 80% of default setting / ** Functioning years per 8 hours / day
7 Communication interfaces
TD410-AD TD710-AD*** - TD810-AD*** - TD820-AD - TD830-AD
*** ETH2 not available on this model.

User manual - HMI Series - 9
7.1 CANopen
7.1.a Using CAN / EXP1 on terminal M1 (Not available for -EL versions)
456 321
ON OFF
DIP2 (DIP1 for TD410 with switch
5/6 ONLY for internal use)
EXP1/CAN with termination
resistor 120Ω
PIN5: GND (brown)
PIN6: CANH (blue)
PIN7: CANL (white)
7. 2 RS232
7. 2 . a Using RS232 / COM1 on DB9 (Not available for TD410 and -EL versions)
Standard RS232 connection:
PIN2: RX (green)
PIN3: TX (blue)
PIN5: GND (brown)
RS232 connection with RTS / CTS:
PIN2: RX (green)
PIN3: TX (blue)
PIN5: GND (brown)
PIN7: RTS (white)
PIN8: CTS (yellow)
7. 3 RS485
7.3. a Using RS485 / COM2 on terminal M1
DIP2 (DIP1 for TD410 with switch 5/6 ONLY for
internal use)
456 321
ON OFF
RS485 MASTER:
Termination 330Ω Polarization
470Ω
456 321
ON OFF
RS485 MASTER:
Polarization only 470Ω
456 321
ON OFF
RS485 SLAVE
PIN3: B+ (green)
PIN4: A- (yellow)
PIN5: GND (brown)

10 - HMI Series - User manual
7.3. b Using RS485 / COM2* MASTER on DB9 (Not available for TD410 and -EL versions)
4321
ON OFF
DIP2: 2,3,4 set to OFF
To use termination resistor on DB9,
short-circuit pin 3 with 4 and 8 with 9
on DB9 for MASTER mode
1
5
9
6
COM2 RS485
EARTH
Pin 5 : C
Pin 8
Pin 7 : 5Vi
Pin 3
470 Ω
470 Ω
330 Ω
B+
A-
MASTER
1 - Input
2 - C
3
4
5 - C
7 - 5V
8
9
Note: 5V Is isolated and can supply 70mA max
* Using the DB9 connector it is possible to introduce termination resistances using DIP2 as for terminal M1 or short-circuiting terminals 3-4 e 8-9, as showed
in the figure.
7.3.c Using RS485 / COM2 SLAVE on DB9 (Not available for TD410 and -EL versions)
4321
ON OFF
DIP2: 2,3,4 set to OFF
Make sure about this setting for DIP2
for SLAVE mode.
No short-circuit on DB9
1 - Input
2 - C
3 -
4 - A-
5 - C
7 - 5V
8 -
9 - B+
1
5
9
6
Pin 5 : C
Pin 8
Pin 7 : 5Vi
Pin 3
470 Ω
470 Ω
330 Ω
SLAVE
COM2 RS485
EARTH
Note: 5V Is isolated and can supply 70mA max
7.4 USB interfaces
HMI comes equipped with a USB 2.0 (Universal Serial Bus) host controller with multiple USB interfaces
accessible externally for the user. This interface is not available on -EL models.
Warning! Peripheral USB devices can be connected to the USB interfaces on this device. Due to the
large number of USB devices available on the market, Pixsys cannot guarantee their performance.
Caution! Because this interface is designed according to general PC specifications, extreme care
should be exercised with regard to EMC, cable routing, etc.
Type USB 2.0
Design Type A
Transfer rate Low speed (1.5 Mbit/s), Full speed (12 Mbit/s), High speed (480 Mbit/s)
Current-carrying capacity Max. 0,8 A (total of all USB ports)
Cable length Max. 3 m (without hub)

User manual - HMI Series - 11
8 Ethernet interface
8.1 Technical data
This Ethernet controller is connected to external devices via the system unit.
Ethernet 1 interface (ETH1) TD410-AD / TD710-AD and -L TD810-AD / TD820-AD / TD830-AD
Number of ports 1 2
Controller LAN8710A
Cabling S/STP (Cat 5e)
Transfer rate 10/100 Mbit/s
10/100 Mbit/s ETH1-ETH2 to CPU
Link
10/100/1000 Mbit/s ETH1-ETH2 link
Cable length Max. 100 m (min. Cat 5e)
LED
Green Link On = Gigabit connection
Off = 10/100 Mbit connection
Yellow 10/100 Mbit Activity On =Link
Blink = Activity (data transfer)
9 Internal ethernet Switch (only TD810-TD820-TD830)
Two Ethernet 10/100/1000 Mbit ports on the rear side of the
operator panel are available. ETH1 and ETH2 are internally
connected to CPU through a Gigabit switch.
Thanks to dual port it is possible to make daisy-chain of more
devices without using external ethernet switches.
Using VLAN system option, each port can be used as
separated network interface. See TDControl user manual for
more details.
For TD410 and TD710 only one Ethernet port is available.
LAPTOP
10 Battery
10.1 Internal battery replacement
BIOS and clock store data also in case of power failure thanks to a CR2032 battery placed on the side.
To replace the battery it is necessary to remove the protection and pull out the extraction box using
a blade screwdriver on models TD410/TD710 or by dedicated battery compartment on TD810 and
greaters.

12 - HMI Series - User manual
10.2 Battery detail
Classification Lithium Coin
Chemical System Lithium / Manganese Dioxide (Li/MnO2)
Nominal Voltage 3.0 Volts
Typical Capacity 235 mAh (to 2.0 volts)
Typical (Li) Content 0.109 grams (0.0038 oz.)
Energy Density 198 milliwatt hr/g, 653 milliwatt hr/cc
Operating Temp -30C to 60C
Warning! CR2032 is a
“Lithium Coin” battery
Danger! KEEP OUT OF REACH OF CHILDREN. Swallowing may lead to serious injury or death in as little
as 2 hours due to chemical burns and potential perforation of the esophagus. To prevent children
from removing batteries, battery compartments is designed to be opened with a screwdriver and is
protected by a security label.
Warning! It is suggested to replace the battery every 3 years. When the battery is removed, an
internal dedicated device allows replacement without data loss if operation is completed within 1
hour since battery removal.
11 TdControlPanel
At switch-on a project starts allowing to verify the machine
general status, date/system hour, related IP address,
SoftPLC execution in background.
Using a VNC client you can view from your PC what is displayed on the PLC / HMI. Starting a browser
with active Java service it is possibile to test if the device Webserver function is active. For this function
it is necessary to use Internet Explorer.
Press “Td Control Panel,” to access the device control
panel and verify/configure all the services and projects
to be launched at starting. It is possible also to configure
the standby time for the backlighting switch off and the
buzzer at display pressure.
The following paragraphs describe each function of the TdControlPanel windows.
NB: Pictures show device standard configuration.

User manual - HMI Series - 13
11. a WIN EXPLORER
From this window it is possible to choose a set of options to
start Windows CE and execute TDControlPanel.
• The first option starts Windows CE with desktop.
• The second option allows TDControlPanel starting if ,
during the switch on , the key
“Stop” is keep pressed .
• Enabling the third option it is possible to set a
protection password to avoid that unauthorized users,
keeping pressed
“STOP” , access TDControlPanel
settings..
“START WINDOWS DESKTOP” allows to start “Explorer.exe” to access Windows CE desktop.
11.b HMI_MOVICON
From this window it is possible to select which Movicon 11
services/programs execute automatically at starting.
The functions of the Movicon scada are available in all
HMI and in “WEB” version PL500 (PL500-335-1AD-WEB)
“START” activates manually the Movicon project (and the file upload service)
11.c PLC LOGICLAB
From this window it is possible to enable/disable the
SoftPLC execution at starting. Selecting
“RUN console
DEBUG”
, during the SoftPLC execution, the Debug window
will be filled with real-time system events to verify possible
anomalies.
NB: this function requires many device resources. It is
suggested to keep it active only if there are problems
during the software development. Disable this function at
the end of the development phase.
“START” activates manually the SoftPLC project (and any debug window).
11.d LAN ETH1
From this window it is possible to modify the device
network configuration parameters. Any modification will
require a restart to be applied.
NB: to transfer the SoftPLC program and Movicon on the
device, it must have a fixed address. It is not possible to
operate in DHCP.
The HMI default IP address is 192.168.0.100
The PL500 default IP address is 192.168.0.99

14 - HMI Series - User manual
11.e BACKLIGHT - BUZZER
From this window it is possible to configure backlighting
and buzzer parameters. Enabling
“Always ON” the
backlighting keeps always active. Otherwise, enter time
value in seconds on “Backlight ON for..(sec)” to enable the
switching off or the lamp attenuation.
The first two fields allows to select the lamp brightness
percentage (100% = ON, 0%=OFF) during standard
operation or standby.
“Buzzer frequency” allows to select the buzzer tone
frequency (an higher frequency corresponds to a more
acute tone). Select
“Buzzer OFF” to deactivate the buzzer at
touch.
“TEST” keys allow to test selected parameters before saving
the configuration.
11.f WINVNC
From this window it is possible to enable/disable the VNC
remote Desktop service. Press
“START VNC” to activate
manually this service. Press “START VNC_CONFIG” to access
VNC configuration window and set the authentication
system or modify access password. NB. Parameter
modification is recommended to expert users, incorrect
parameters modification will cause remote desktop service
malfunctioning. Default password to access remote
Desktop through VNC is “1234”.
11.g BACKUP-RESTORE
BACKUP of LogicLab and Movicon projects stored on HMI.
After downloading LogicLab and Movicon projects on HMI
and after setting the HMI for their automatic execution at
each starting, switch off the HMI and restart it keeping the
STOP icon pressed.
TDControlPanel window will be opened
Insert a USB pen (FAT32 formatted) in one of the available
USB ports.
Press BACKUP-RESTORE to access the utility for projects
backup and device configuration

User manual - HMI Series - 15
This window allows to select backup options:
- PLC_LOGICLAB (RUNTIME PROJECT): for backup of LogicLab project and complete Runtime and
also of the configuration completed in the window PLC_LOGICLAB (accessible from main window
of TDControlPanel)
- HMI_MOVICON (PROJECT): for backup of single Movicon project and configuration completed in
the window HMI_MOVICON (accessible from main window of TdControlPanel)
- HMI_MOVICON (RUNTIME): backup only for Runtime
- TdControlPanel (Configuration): for backup of complete configuration performed within different
utilities accessible from main window of TdControlPanel. *Attention: this backup will include also
the eventual Password for TdControl Panel if it has been set in WIN EXPLORER
- LAN (IP CONFIGURATION): for backup of network settings of HMI
- BOOT SCREEN: for backup of background image visualized during system start up
Tick all boxes to obtain a complete backup of the settings and software projects stored on the HMI.
This is useful and time-saving when requested to program multiple HMIs for same application.
Press BACKUP TO USB DISK to open USB memory
connected to the device; it will be possible to select
destination folder and name for backup file 8default file
name will be date and time of backup creation)
Press OK to start backup (Hourglass will show up ).
A confirmation popup will advice when process will be
completed. Press OK to close popup , press ESC , then the
device may be switched off.
RESTORE procedure to restore LogicLab and Movicon projects on HMI.
To program a new HMI starting from an existing Backup
keep pressing STOP icon during start up of the device
TDControlPanel window will be opened

16 - HMI Series - User manual
Insert the USB pen containg Backup files on one of the
available USB ports.
Press BACKUP-RESTORE
Press RESTORE FROM USB DISK to open USB memory
connected to the HMI and select the chosen backup file
Press OK to start Restore process (Hourglass will show up).
A confirmation popup will advice when process will be
completed. Press OK to close popup, press ESC, then the
device may be switched off.
From now on at each start the HMI will start the projects (and eventually the complete configuration
if selected ) automatically.
12 LogicLab Suite
LogicLab Suite is the Pixsys development environment for the programming of PLC series, PL500 and
all Operator panels / PanelPC.
The suite is available for free download within
“download area” of the website pixsys.net, no activation
code is required (only registration). Supported by all 32/64bit Windows versions, starting from
Windows XP SP3. Available both in English and Italian version. Once downloaded the setup file on
the computer, start the installation and follow the standard procedure. The program can be activated
through the icon ”LogicLab” (on desktop) or from the menu
“Start” > “PixsysSuite” > “LogicLab” .
12.a Language modification
To modify the visualization language it is
necessary to open options window form the
menu
“File” > “Options” , go to “Language” , select
“ITA - italiano” and press
“Select” . Confirm with
“OK” , close and re-open LogicLab to enable the
modification.

User manual - HMI Series - 17
12.b Create - load a project
Open an exsisting project:
• With LogicLab opened, click on
“Open
project”
or select one of the last projects
form the list.
• With LogicLab closed, enter on the project
folder and select (double click) the chosen
file (icon and extension “.plcprj”).
Create a new project:
Press
“New project” .
Enter the name of the new project and select
the folder where the project files will be stored.
Finally, select the device to be programmed.
Attention: selecting “respect capital/lowercase letters”, a variable which contains a capital letter
will be understood as different from another with the same name but with this letter lowercase. It
is recommended to keep this selection disabled, to avoid any confusion during the drafting of the
program code.
12.c Connection to target
Here below please find the necessary requirements for the correct connection between target (device
to be programmed) and the development environment on PC (LogicLab).
Target requirements:
• device ON and started
• configured with static IP address compatible with the network where there is the PC to which it will
connect. By default, the IP address of the HMI is 192.168.0.100, for PL500 is 192.168.0.99, so the PC
must have the same network and class (in this case 192.168.0.XXX) but different physical address
(the last 3 digits of the IP address, with a number between 1 and 255, different from 100). If it is
necessary to modify the IP address of the terminal, refer to the TD Control Panel configuration,
section “LAN ETH1” on par. 10.d.
• connection with net cable (direct or cross) directly to PC or through a net switch
• SoftPLC in execution (refer to TD Control Panel configuration, section
“PLC LOGICLAB” on par. 10.c).
PC requirements:
• IP address compatible with the network where it is located and with the IP address configured on
the target (see previous points)
• antivirus/firewall which allows the connection to network devices (normally already correctly
configured)
• LogicLab configured for the connection to the target to be programmed: menu
“On Line” > “Select
communication”
, on the window that opens press “Properties” and than enter the target IP on “IP
Address”
, keeping all the rest unaltered. In case of very slow networks or of a network configuration
with different switches, it is possibile to increase the
“Timeout” value (expressed in mS).

18 - HMI Series - User manual
The image represents default configuration
Confirm all windows pressing
“OK” and save through or from the menu “file” > “SaveProject” .
To verify the correct LogicLab and Target configurations, it is possible to make the connection pressing
or form the menu “On Line” > “Connect” . If the connection is correctly done, the status bar at the
lower right side will visualize
“CONNECTED” and “NO CODE” (to indicate that the target is connected
and has no code in it) or
“DIFF CODE” (to indicate that the code which is being visualized does not
correspond to those who lies in the target).
12.d Compiling and downloading the code
Once entered the project code it is necessary to verify eventual errors pressing F7, clicking on icon
or from the menu
“Project” > “Fill” .
If the compilation is correctly done it is possible to transfer the program to the target pressing F5,
through icon or from the menu
“On Line” > “Code transferring” .
The status bar will show
“CONNECTED” and “SOURCE OK” indicating that the program running on the
target corresponds to that which is visualized on PC.
12.e Watch window
If the program running on the target corresponds to that which is being visualized on PC, the status
bar will show
“CONNECTED” and “SOURCE OK” and it is possible to use the window “Watch” to verify
real-time the status of the variables used in the project. To enable the window
“Watch” , press CTRL+T
or use
“View” > “View tool window” > “Watch” . To add a variable to the window “Watch” , just drag it inside
or press the icon and select it manually.
From now on, the window “Watch” will visualize
the value of the inserted variable, in real time.
Through it is possible to save, load and add an exsisting watch-list to the list of variables.

User manual - HMI Series - 19
To change the visualization format, it is
necessary to select the variable and press .
On the window that opens, select the chosen
format and confirm pressing
“OK” .
13 Interfacing Movicon 11 with LogicLab
NB: Movicon 11.5 or greater.
To execute only once:
Following steps are to be completed on the PC which will be used to develop the projects.
Go to download area of Pixsys website / Movicon section and download “MOVICON 11.6 Update-Ag-
giorna Driver.exe” corresponding to your PC system. Double click to launch the .exe file and follow
instructions.
Do the same procedure also if a Panel PC (TD750-TD850-TD900-TD910-TD920) is used.
Note: with this procedure all PLC system variables and variables created and used in the PLC are
imported.
The creation and the updating of the PLC variables list is done only if the LogicLab program is
compiled without errors and downloaded on the target.
13.a Creating a new Movicon project
Start the software and choose the platform “
Windows® X86 / X64 ” for Panel-PC or “ Windows® CE
Platform
” for HMI and for “WEB” version of PL500. If the new Movicon project is being created following
the Wizard, at the end it will visualize the driver configuration window, switch to the section
“Driver
Configuration”
to par. 12.b. If the driver is being installed manually, proceed as follow:
Add the communication driver with a
right click on
“Real time DB” and then “new
communication driver”
.
Select “Pixsys” from the manufacturer menu
and then
“Pixsys SoftPLC Driver” .
Confirm with
“OK” and double click on the
driver just created to open the configuration
window.

20 - HMI Series - User manual
13.b Driver configuration
Select “Station” and add a new station pressing
“ADD” .
1. Enter source path of the LogicLab project
locatedonthe PC used for development. This
allows to import variables, execute Movicon
in preview mode on own PC, including
communication with SoftPLC, and perform
complete test. Next step is to indicate IP
address of the target HMI/PC (only after
completing development it will be necessary
to enter localhost address
127.0.0.1 to enable
communication of Movicon project with the
softPLC of the panel itself.
2.
This field is self-compiling after entering path as described on previous point. If using an HMI/PL500,
do not modify the self-compiling field; if using a Panel PC (TD750, TD850 etc…) enter the path used
for download of the LogicLab project (default D:\LLExec\ NameMyProjectLogicLab.sym.xml).
3. If Movicon project will be executed on the HMI/PC where the softPLC is also installed, then the IP
address will be 127.0.0.1. If it will be executed on a different HMI/PC, then enter the IP address of the
softPLC.
4. From the section “General” assign a name to the station, ex. “PLC” .
Press OK to save settings and exit.
Now it is possible to import the LogicLab
project variabiles on Movicon.
Right click on
“SoftPLC Pixsys” and select “Import
PLC database”
.
Press “Read from PLC project” , the list of all
available variables will be provided.
Select variables to be imported and press
“Import” .
NB: If importing an array variable, it will be visualized as a structure carrying the array name.
Single array members will be accessible individually with following syntax
NameMyArray:NameMyArray
_X
where X is the array index (starting from 0).
Now variables are available on the Movicon project. If it is necessary to import new variables (to modify
LogicLab project), repeat only the reading and import variables procedure.