Planet LN501 User manual
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 1 -
- 2 -
- 3 -
- 4 -
- 5 -
- 6 -
- 7 -
- 8 -
1. Package Contents
Thank you for purchasing PLANET Industrial LoRa Node Controller,
LN series. The descriptions of these models are as follows:
LN501 Outdoor IP67 LoRa Node Controller with Solar Panel
LN1152 Indoor IP30 LoRa Node Controller
“LoRa Node” is used as an alternative name in this Quick
Installation Guide.
Open the box of the LoRa Node and carefully unpack it. The box
should contain the following items:
LN501 LN1152
LoRa Node Controller x 1
Quick Installation Guide x 1
Data Cables x 2
Mounting Bracket x 1
Wall Mounting Kits x 1
Hose Clamps x 2
2550 mAh Battery x 2
LoRa Node Controller x 1
Quick Installation Guide x 1
LoRa Antenna x 1
12-Pin Terminal Block x 1
Wall Mounting Screws x 2
Power Adapter x 1
If any item is found missing or damaged, please contact your local
reseller for replacement.
Caution
1.Never put batteries in mouth. If swallowed, contact
your physician or local poison control center.
2.Do not short circuit; may cause burns or catch fire.
3.Batteries should not be exposed to excessive heat
such as sunshine, fire or the like.
3. Hardware Installation
Refer to the illustration and follow the simple steps below to
quickly install your LoRa Node.
3.1 LN501
3.1.1 Remove cover for setting analog input or power
output
When changing the analog input or power output of LN501 via DIP
switch, follow the steps below:
Step 1: Removethescrewcapsandtakeotheroofcover.
3.1.3 Wall Mounting
Make sure you have a wall mounting bracket, bracket mounting
screws, wall plugs, wall mounting screws and other required tools.
Step 1: Mark the four holes on the wall you prefer to place the
device and drill the marked four holes for the wall plugs
(anchors). Then place the mounting bracket over the
holes with the wall plugs inside, and tighten it with the
screws.
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
3.1.4 Pole Mounting
Step 1: Straighten out the clamp and slide it through the
rectangular rings in the mounting bracket, and wrap the
clamp around the pole. Then use a screwdriver to tighten
the clamp by turning it clockwise.
Power Button:
Function Action LED Indication
Turn On Press and hold the button
for more than 3s. OOn
TurnO Press and hold the button
for more than 3s. On O
Reset Press and hold the button
for more than 10s. Blinks.
CheckOn/O
Status
Quickly press the power
button.
Light On: Device is on.
LightO:Deviceiso.
Note
Please turn off the device before changing DIP
switches.
Step 3: Put back the roof cover and screw the screws.
Note
1.Analog input is set to 4-20mA by default; power
output is set to 12V by default.
2.Power output on interface 1 is used for powering
serial port devices and power output on interface 2
is used for powering analog devices.
2. Requirements
Workstations running Windows 10/XP/2003/Vista/7/8/2008.
Type C USB cable for LN501.
Micro USB cable for LN1152.
Step 2: Choose or change an analog input and power output via
DIP switch.
DIP Switch:
Interface DIP Switch
Power
Output
12V:1on2o3o(default)
9V:1o2on3o
5V:1o2o3on
Analog
Input
Disable:1o2o3o
4-20mAADC:1o2on3on(default)
0-10VADC:1on2o3o
RS485
Disable:1o2o3o(default)
Add120ΩresistorbetweenAandB:1on2o3o
Add1kΩpull-upresistoronA:1o2on3o
Add1kΩpull-downresistoronB:1o2o3on
3.1.2 Data Interface
Data Interface 1
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4Analog Input 1
5Analog Input 2
65-24V DC IN
Data Interface 2
Pin Description
15V/9V/12V OUT (Switchable)
23.3V OUT
3GND
4GPIO1
5GPIO2
6
RS232/RS485 (Switchable)
7
8Reserved
PIN RS232 RS485
6Tx A
7Rx B
Step 2: Place the device on the mounting bracket and put the
small screw into the hole found on the bottom of the
deviceandthentightenthescrewtonishthejob.
Note
Please make sure the screws are tightly fixed.
3.2 LN1152
3.2.1 Antenna Installation
Step 1: Rotate the antenna into the antenna connector
accordingly.
Step 2: The external LoRa antenna should be installed vertically
for a good signal.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
- 9 -
- 10 -
- 11 -
- 12 - - 13 - - 14 -
3.2.2 Data Interface and Power Interface
GND
VIN
RXD
TXD
GND
A
B
IN
IN_COM
OUT_COM
OUT_NC
OUT_NO
PIN Denition Description
1GND Ground
2VIN 5-24V DC
3RXD
RS2324TXD
5GND
6 A RS485
7 B
8IN DI
9IN_COM
10 OUT_COM
DO11 OUT_NC
12 OUT_NO
Note
OUT_NC = Normally Closed, OUT_No = Normally
Open.
3.2.3 LED Indicators
LED Indication Status Description
System System
Status
Static System Start-up
Onfor500ms,o
for 500 ms
The system is
running properly.
Onfor200ms,o
for 200 ms
The system is not
connected to server.
ACT Network
Status
O Failed to access the
network
Onfor500ms,o
for 500 ms
Accessed the network
successfully
3.2.4 Wall Mounting
Step 1: Align the LN1152 device horizontally to the desired
position on the wall and use a marker pen to mark two
mounting holes on the wall.
Step 2: Drill the two holes marked previously on the wall by
using your drill with a 6 mm drill bit.
Step 3: Mount the device to the wall by tightly screwing the wall
mounting screws (M3 * 20) into the device mounting
holes.
4. Managing LoRa Node
1. Download ToolBox software from Planet web site.
https://www.planet.com.tw/en/support/downloads?&method=key
word&keyword=LN501&view=6#list
2. Power on the LoRa Node device and then connect it to computer
via micro USB port.
3. Open the ToolBox and select “Type” and then "General", and
then click password to log in ToolBox. (Default password:
123456)
4. After logging in the ToolBox, you can click “Power On” or “Power
O”toturnon/odeviceandchangeothersettings.
3.2.5 Wiring Power Input
LN1152 series supports 5-24V DC power supply. You can use other
supplies or power adapter to power on the device.
Note
For industrial applications, it’s suggested not to
release the metal case and use an independent
power supply.
5. Customer Support
You can browse our online FAQ resource and User’s Manual on
PLANET Web site rst to check if it could solve your issue. If you
need more support information, please contact PLANET support
team.
PLANET online FAQs:
https://www.planet.com.tw/en/support/faq.
php?method=keyword&keyword=LN
Support team mail address:
support@planet.com.tw
LN Series User’s Manual:
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN501&view=3#list
https://www.planet.com.tw/en/support/downloads?&method=keywo
rd&keyword=LN1152&view=3#list
(Please select your model name from the drop-down menu of
Product Models.)
Copyright © PLANET Technology Corp. 2022.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp.
All other trademarks belong to their respective owners.
Other manuals for LN501
3
Table of contents
Other Planet Controllers manuals
Planet
Planet NMS-500 User manual
Planet
Planet WAPC-500 User manual
Planet
Planet LN501 User manual
Planet
Planet NMS-360 User manual
Planet
Planet NMS-500 User manual
Planet
Planet UNC-NMS User manual
Planet
Planet LN501 User manual
Planet
Planet LN501 User manual
Planet
Planet WAPC-1232HP User manual
Planet
Planet NMS-1000V User manual
