Planet ICA-HM620 User manual

PoE Plus Speed Dome IP Camera
ICA-HM620 / ICA-H652
Quick Installation Guide

Table of Contents
Verify the Contents Inside the Package Box ....................................................... 3
Physical Installation ......................................................................................... 4
Further Conguration ......................................................................................12

3
Verify the Contents Inside the Package Box
The package should contain the items below. If any item is missing or damaged,
please contact the seller immediately.
Dome Camera with Dome
Cover Compact Pendent Mount Outdoor Mount Kit
Waterproof Rubber Terminal Block Bracket Screw Kit
Security Tool Lubricant M3/M5 Standard Screws
M3/M5 Security Screws
AC Power Adapter
Quick Installation Guide CD-ROM Power Cord

4
Physical Installation
Caution
1. Please take necessary precautions when installing the hardware
to avoid damage to the device and injury to the installer.
2. Please make sure the hardware is fastened on the wall properly
to avoid unnecessary accidents.
Double-check the hardware again after the installation.
3. Please check whether or not the power supply voltage is suitable
for the device. The wrong power supply voltage will damage the
device.
Step 1
Unpack the Dome Camera’s package and take out the Dome Camera unit.
Step 2
Tighten the knob to remove the dome cover and the lens protector.

5
Step 3
Attach the dome cover to the camera body. Before doing that, apply some lubricant
to the cover’s water-proof rubber to make the installation process smoother.
Note
The tiny protrusion on the dome cover must align with one of the
four holes on the dome body.
Step 4
Gently pressure the dome cover downward with two hands on the side of it.
DO NOT press the cover, as shown in the gure; this might cause damage to the
camera body.

6
Step 5
Use the M3 screw to screw the dome cover and camera body together.
Step 6
Make a cable entry hole on the wall to
recess the cables. Otherwise, users could
push up the Cable Entry Board on the
Compact Pendent Mount’s Mounting Plate
to place the cables, as shown in the photo
on the right.
Step 7
Fix the Compact Pendent Mount on the wall with proper screws and screw anchors.
After this step, attach the Waterproof Rubber to the Outdoor Wall Mount.
Note
The screws and screw anchors are not in the package.

7
Step 8
Pass the network and power cable through the Compact Pendent Mount
Note
1. The network cable is not in the package.
2. Please block the cable entry hole with the supplied sponge to
avoid insects entering the Pendent Mount. The sponge can be
placed in two ways as shown in the illustrations below.

8
Step 9
Thread the cables through the Outdoor Mount Kit and join the Outdoor Mount Kit
to the Compact Pendent Mount with the supplied screws and washers. Then adjust
the Waterproof Rubber to the joint.
Step 10
Connect power wires of AC adapter with Power Input connector of data cable.
Please check the color of power wire carefully, and screw that with connector
properly.
Blue Yellow/Green
Brown
Black Green
White
Caution
Wrong wiring could cause permanently damage to the device.

9
Step 11
Use the safety hook to hang the camera, and connect the cables to the Dome
Camera.



10
Step 12
Assemble the Dome Camera to the Outdoor Mount Kit with the supplied M5 screw
and washers.
Note
Rotate the dome camera until the two screw holes match the dome
camera with the outdoor mount kit.
Step 13
The adapter with the power cord attached is connected to a power outlet where
the power voltage matches.
Voltage Switch
Note
Use only the power adapter shipped with the unit to ensure correct
functionality

11
Step 14
Connect the network cable with switch. The speed dome can be congured without
external power if connected to IEEE 802.3at High Power over Ethernet (PoE plus)
switch.
AC
Ethernet Switch
Speed Dome
User PC
(192.168.0.X)
Note
1. For ICA-HM620, if there is a need to operate the Heater, please
plug the AC 24V cable into the Camera’s Power Connector to
power up the Camera instead. Heater can only be powered by
the 24VAC adapter.
2. For ICA-H652, the Heater can be powered by the 24VAC adapter
or 60-watt PSE device.
Step 15
Set your computer’s IP address to 192.168.0.x, where x is a number between 1
and 253 (except 20 which is being used for the camera by default). If you don’t
know how to do this, please ask your network administrator.
Step 16
Use web browser (Internet Explorer 6.0 or above) to connect to 192.168.0.20
(type this address in the address bar of web browser).
You’ll be prompted to input user name and password: admin and admin

12
Further Conguration
For the detailed conguration, please check user’s manual on the bundled CD.
If you have any other question, please contact the dealer where you purchased
this product or you can contact PLANET directly at the following email:
Email address: [email protected]