Planet FNSW-2400PS User manual

User's Manual
FNSW-2400PS
24-Port 10/100Mbps
POE Web Smart Ethernet Switch
- 1 -

User’s Manual of FNSW-2400PS
Trademarks
Copyright ©PLANET Technology Corp. 2011.
Contents subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All other trademarks belong to their respective
owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work properly in all environments and applications,
and makes no warranty and representation, either implied or expressed, with respect to the quality, performance,
merchantability, or fitness for a particular purpose.
PLANET has made every effort to ensure that this User’s Manual is accurate; PLANET disclaims liability for any
inaccuracies or omissions that may have occurred.
Information in this User’s Manual is subject to change without notice and does not represent a commitment on the
part of PLANET. PLANET assumes no responsibility for any inaccuracies that may be contained in this User’s
Manual. PLANET makes no commitment to update or keep current the information in this User’s Manual, and
reserves the right to make improvements to this User’s Manual and/or to the products described in this User’s
Manual, at any time without notice.
If you find information in this manual that is incorrect, misleading, or incomplete, we would appreciate your
comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the Instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
CE Mark Warning
This is a Class A product. In a domestic environment, this product may cause radio interference, in which case
the user may be required to take adequate measures.
Energy Saving Note of the Device
This power required device does not support Standby mode operation.
For energy saving, please remove the power cable to disconnect the device from the power circuit.
Without removing power cable, the device will still consuming power from the power source. In the view of Saving
the Energy and reduce the unnecessary power consuming, it is strongly suggested to remove the power con-
nection for the device if this device is not intended to be active.
WEEE Warning
To avoid the potential effects on the environment and human health as a result of the presence of
hazardous substances in electrical and electronic equipment, end users of electrical and electronic
equipment should understand the meaning of the crossed-out wheeled bin symbol. Do not dispose of
WEEE as unsorted municipal waste and have to collect such WEEE separately.
Revision
PLANET 24-Port 10/100Mbps POE Web Smart Ethernet Switch User's Manual
FOR MODEL: FNSW-2400PS
REVISION: 1.1(OCTOBER.2011)
Part No.: 2081-A81180-001
- 2 -

User’s Manual of FNSW-2400PS
TABLE OF CONTENTS
1. INTRODUCTION ...............................................................................6
1.1 CHECKLIST ................................................................................................................................................ 6
1.2 ABOUT THE SWITCH ................................................................................................................................... 6
1.3 FEATURES ................................................................................................................................................. 7
1.4 SPECIFICATION .......................................................................................................................................... 8
2. HARDWARE DESCRIPTION ............................................................10
2.1 FRONT PANEL .......................................................................................................................................... 10
2.1.1 LED Indicators................................................................................................................................. 10
2.2 REAR PANEL............................................................................................................................................ 10
2.3 HARDWARE INSTALLATION ........................................................................................................................ 11
2.3.1 Desktop Installation......................................................................................................................... 11
2.3.2 Rack Mounting ................................................................................................................................12
3. SWITCH MANAGEMENT .................................................................14
3.1 OVERVIEW ............................................................................................................................................... 14
3.2 MANAGEMENT METHOD............................................................................................................................ 14
3.2.1 Web Management........................................................................................................................... 14
3.3 LOGGING ON TO THE FNSW-2400PS ....................................................................................................... 15
4. WEB MANAGEMENT........................................................................16
4.1 LOGIN IN TO THE SWITCH .......................................................................................................................... 16
4.2 ADMINISTRATOR....................................................................................................................................... 17
4.2.1 System Information ......................................................................................................................... 18
4.2.2 IP Configuration .............................................................................................................................. 19
4.2.3 Password Setting ............................................................................................................................ 20
4.2.4 Factory Default................................................................................................................................20
4.2.5 Firmware Update ............................................................................................................................ 21
4.2.6 Reboot............................................................................................................................................. 22
4.3 PORT MANAGEMENT ................................................................................................................................23
4.3.1 Port Configuration ........................................................................................................................... 24
4.3.2 Port Mirroring .................................................................................................................................. 25
4.3.3 Bandwidth Control........................................................................................................................... 26
4.3.4 Broadcast Storm Control................................................................................................................. 27
4.3.5 Port Statistics .................................................................................................................................. 27
4.4 VLAN SETTING........................................................................................................................................ 29
4.4.1 VLAN Mode..................................................................................................................................... 32
4.4.1.1 Port Base VLAN Mode................................................................................................................. 33
4.4.1.2 Tag Base VLAN Mode ................................................................................................................. 33
4.4.2 VLAN Member................................................................................................................................. 34
4.4.3 Multi to 1 Setting ............................................................................................................................. 36
- 3 -

User’s Manual of FNSW-2400PS
4.5 QOSSETTING.......................................................................................................................................... 37
4.5.1 Priority Mode................................................................................................................................... 37
4.5.2 Class of Service .............................................................................................................................. 38
4.6 SECURITY ................................................................................................................................................ 41
4.6.1 MAC Address Binding..................................................................................................................... 42
4.6.2 TCP / UDP Scan ............................................................................................................................. 43
4.6.3 TCP / UDP Filter ............................................................................................................................. 43
4.6.4 IP Address Filter ............................................................................................................................. 45
4.7 SPANNING TREE....................................................................................................................................... 46
4.7.1 STP Bridge Settings........................................................................................................................ 47
4.7.2 STP Port Settings ........................................................................................................................... 48
4.7.3 Loopback Detection Settings .......................................................................................................... 50
4.8 TRUNKING................................................................................................................................................ 51
4.9 DHCP RELAY AGENT ............................................................................................................................... 53
4.9.1 DHCP Relay Agent ......................................................................................................................... 54
4.9.2 Relay Server ................................................................................................................................... 55
4.9.3 VLAN MAP Relay Agent ................................................................................................................. 55
4.10 BACKUP/RECOVERY ............................................................................................................................... 56
4.11 MISCELLANEOUS .................................................................................................................................... 57
4.11.1 Miscellaneous Settings ................................................................................................................. 57
4.11.2 IGMP Static Router Settings ......................................................................................................... 58
4.12 SNMP SETTINGS ................................................................................................................................... 59
4.13 SAVE SETTINGS ..................................................................................................................................... 60
4.14 LOGOUT ................................................................................................................................................ 60
5. SWITCH OPERATION......................................................................61
5.1 ADDRESS TABLE ...................................................................................................................................... 61
5.2 LEARNING ................................................................................................................................................ 61
5.3 FORWARDING &FILTERING ....................................................................................................................... 61
5.4 STORE-AND-FORWARD............................................................................................................................. 61
5.5 AUTO-NEGOTIATION ................................................................................................................................. 62
6. POWER OVER ETHERNET OVERVIEW..............................................63
7. THE POE PROVISION PROCESS ......................................................65
7.1 LINE DETECTION ...................................................................................................................................... 65
7.2 CLASSIFICATION....................................................................................................................................... 65
7.3 START-UP ................................................................................................................................................ 66
7.4 OPERATION.............................................................................................................................................. 66
7.5 POWER DISCONNECTION SCENARIOS........................................................................................................ 66
- 4 -

User’s Manual of FNSW-2400PS
8. TROUBLESHOOTING.......................................................................67
APPENDIX A NETWORKING CONNECTION..........................................68
A.1 SWITCH‘S RJ-45 PIN ASSIGNMENTS ......................................................................................................... 68
A.2 RJ-45 CABLE PIN ASSIGNMENT ................................................................................................................. 68
A.3 DATA OUT POEINJECTOR RJ-45 PORT PIN ASSIGNMENTS ..................................................................... 69
- 5 -

User’s Manual of FNSW-2400PS
1. INTRODUCTION
1.1 Checklist
Check the contents of your package for following parts:
zFNSW-2400PS x1
zQuick Installation Guide x1
zUser's Manual CD x1
zPower Cord x 1
zRubber Feet x 4
zTwo Rack-mounting Brackets with Attachment Screws x1
If any of these pieces are missing or damaged, please contact your dealer immediately, if possible, retain the carton
including the original packing material, and use them against to repack the product in case there is a need to return it to
us for repair.
In the following section, the term “POE Web Smart Ethernet Switch” means the Switch device, ie. FNSW-2400PS;
term of “switch” can be any third switches.
1.2 About the Switch
The FNSW-2400PS provides 24 10/100Mbps POE Fast Ethernet ports, the Web Smart PoE Switch supports MDI / MDI-X
convertible on 24 10/100Mbps ports and also provides PoE inject function on port#1 to port#24 which is able to drive at
least 8 IEEE 802.3af 15.4Watts compliant powered devices.
The unshielded twisted-pair (UTP) cable ports providing dedicated 10/100Mbps bandwidth, the dual speed ports used
standard twisted-pair cabling and are ideal for SOHO or segmenting networks into small. Each 10/100Mbps port can
supports up to 200Mbps of throughput in full-duplex mode, the POE Web Smart Ethernet Switch also provides a simple,
cost-effective, and highly reliable network connection for data as well as power. Furthermore, it is the ideal device for
bridging among Ethernet, Fast Ethernet workgroups and networks.
The FNSW-2400PS equipped with non-blocking 4.8Gbps backplane, greatly simplifies the tasks of upgrading your LAN for
catering to increase bandwidth demands.
For efficient management, the FNSW-2400PS is equipped with remote Web interface. The Web Smart PoE Switch can be
programmed for advanced switch management functions such as SNMP , port configuration, port-based / IEEE 802.1Q /
MTU VLAN, port mirroring, port trunk, QoS, bandwidth control, broadcast storm control, MAC address / TCP & UDP filter
and IGMP Snooping v1/v2.
- 6 -

User’s Manual of FNSW-2400PS
1.3 Features
¾Physical Port
24-Port 10/100Mbps Fast Ethernet ports with PoE Injector
Reset button for system management
¾PoE
Complies with IEEE 802.3af Power over Ethernet Mid-Span PSE
Up to 24 IEEE 802.3af devices powered
Supports PoE Power up to 15.4 Watts for each 802.3af PoE port
Auto detect powered device (PD)
Circuit protection prevents power interference between ports
Remote power feeding up to 100m
¾Layer 2 Features
Auto-MDI/MDI-X detection on each RJ-45 port
Prevents packet loss with back pressure (Half-Duplex) and IEEE 802.3x PAUSE Frame Flow control
(Full-Duplex)
Support VLAN:
- IEEE 802.1Q Tag-based VLAN
- Port-Based VLAN
- MTU VLAN (Multi-Tenant Unit VLAN)
Support Link Aggregation
−up to 2 trunk groups
−up to 4 Fast Ethernet ports per trunk group
−IEEE 802.3ad LACP (Link Aggregation Control Protocol)
Support Spanning Tree Protocol
- STP, IEEE 802.1D (Classic Spanning Tree Protocol)
- RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
- Loopback Detection
Port Mirroring to monitor the incoming or outgoing traffic on a particular port
¾Quality of Service
2 priority queues on all switch ports
Traffic classification:
- Port-Based priority
- IEEE 802.1p-Based priority
- IP TOS / DSCP-Based priority
- TCP / UDP Port Based QoS
Strict priority and Weighted Round Robin (WRR) CoS policies
In/Out rate limit control on each port
Broadcast Storm Control support
¾Multicast
Supports IGMP Snooping v1 and v2
¾Security
MAC address filter
TCP & UDP filter on each port
- 7 -

User’s Manual of FNSW-2400PS
Management idle time security
¾Management
Remote Web interface for Switch management and setup
Supports SNMP v1
Supports DHCP Option82 and DHCP Relay
Firmware upgrade through Web interface
Configuration upload / download through Web interface
Reset button for system reboot or reset to factory default
1.4 Specification
Model FNSW-2400PS
Hardware Specification
Ports 24 10/100Base-TX RJ-45 Auto-MDI/MDI-X interfaces
Switch Processing Scheme Store-and-Forward
Throughput (packet per second) 3.57Mpps@64Bytes
Switch Fabric 4.8Gbps
Address Table 8K entries
Share Data Buffer 1.75Mb embedded memory for packet buffers
Flow Control Back pressure for Half Duplex, IEEE 802.3x Pause Frame for Full Duplex
Dimensions (W x D x H) 445 x 207 x 45 mm (1U height)
Weight 2.55kg
Power Requirement 100~240V AC, 50-60 Hz, 2A
Power Consumption / Dissipation Max.135 Watts / 460 BTU
Smart Function
System Configuration Web interface, SNMP v1
Port Configuration Port Speed Duplex mode selection
Port Disable / Enable
Bandwidth Control Yes
Broadcast Storm Control Yes / Threshold 1~63
Port Statistics Display each port’s detail Ethernet traffic counter information
VLAN
24 Port-based VLAN groups
32 IEEE 802.1Q VLAN groups
MTU VLAN
Spanning Tree Protocol STP, IEEE 802.1D (Spanning Tree Protocol)
- 8 -

User’s Manual of FNSW-2400PS
RSTP, IEEE 802.1w (Rapid Spanning Tree Protocol)
Port Trunking Support 2 groups of 4-Port 10/ 100Base-TX trunk support
Up to 800Mbps bandwidth per trunk (Full-Duplex)
Port Mirroring Port mirroring allows monitoring of the traffic across any port in real time
QoS Allow to assign low / high priority on each port.
First-In-First-Out, All-High-before-Low, Weight-Round-Robin QoS policy.
MAC Address / TCP & UDP Filter Yes
IGMP Snooping v1 / v2 Allow to Disable or Enable.
Power over Ethernet
PoE Standard IEEE 802.3af Power over Ethernet / PSE
PoE Power Supply Type Mid-Span
PoE Power output Per Port 48V DC, 350mA . Max. 15.4 watts
Power Pin Assignment 4/5(-), 7/8(+)
PoE Power Budget 125Watts
Standards Conformance
Regulation Compliance FCC Part 15 Class A, CE
Standards Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3af Power over Ethernet (15.4Watts)
IEEE 802.3x Full-duplex flow control
IEEE 802.1Q VLAN
IEEE 802.1p QoS
IEEE 802.1D Spanning Tree Protocol
IEEE 802.1w Rapid Spanning Tree Protocol
Environment
Temperature Operating: 0~50 Degree C
Storage: -10~70 Degree
Humidity Operating 5% to 95%, Storage: 5% to 95% (Non-condensing)
- 9 -

User’s Manual of FNSW-2400PS
2. HARDWARE DESCRIPTION
This product provides two different running speeds – 10Mbps and 100Mbps in the same POE Web Smart Ethernet Switch
and automatically distinguishes the speed of incoming connection.
This section describes the hardware features of FNSW-2400PS. For easier management and control of the
FNSW-2400PS, familiarize yourself with its display indicators, and ports. Front panel illustrations in this chapter display the
unit LED indicators. Before connecting any network device to the FNSW-2400PS, read this chapter carefully.
2.1 Front Panel
The Front Panel of the FNSW-2400PS consists of 24x Auto-Sensing 10/100Mbps Ethernet RJ-45 Ports
The LED Indicators are also located on the front panel of the POE Web Smart Ethernet Switch.
Figure 2-1: FNSW-2400PS Switch Front Panel
2.1.1 LED Indicators
System
LED Color Function
PWR Green Lights Indicate that the Switch has power.
Per 10/100Base-TX, PoE interfaces (Port-1 to Por-24)
LED Color Function
Lights: Indicate the link through that port is successfully established.
LNK/ACT Green Blink: Indicate the Switch is actively sending or receiving data over that port.
Lights:Indicate the port is providing 48VDC in-line power.
PoE In-Use Orange OFF: Indicate the connected device is not a PoE Powered Device (PD).
1. Press the RESET button once. The POE Web Smart Ethernet Switch will reboot automati-
cally.
2. Press the RESET button for 5 ~ 10 seconds. The POE Web Smart Ethernet Switch will back to
the factory default mode; the entire configuration will be erased.
2.2 Rear Panel
The rear panel of the POE Web Smart Ethernet Switch indicates an AC inlet power socket, which accepts input power from
100 to 240VAC, 50-60Hz, 2A.
Figure 2-2: FNSW-2400PS Switch rear panel
- 10 -

User’s Manual of FNSW-2400PS
Power Notice:
1. The device is a power-required device, it means, it will not work till it is powered. If your networks should active all the
time, please consider using UPS (Uninterrupted Power Supply) for your device. It will prevent you from network data
loss or network downtime.
2. In some area, installing a surge suppression device may also help to protect your POE Web Smart Ethernet Switch
from being damaged by unregulated surge or current to the POE Web Smart Ethernet Switch.
2.3 Hardware Installation
This part describes how to install your POE Web Smart Ethernet Switch and make connections to the Switch. Please read
the following topics and perform the procedures in the order being presented. To install your POE Web Smart Ethernet
Switch on a desktop or shelf, simply completed the following steps.
2.3.1 Desktop Installation
To install POE Web Smart Ethernet Switch on a desktop or shelf, simply completed the following steps:
Step 1: Attached the rubber feet to the recessed areas on the bottom of the POE Web Smart Ethernet Switch.
Step 2: Place the POE Web Smart Ethernet Switch on a desktop or shelf near an AC power source.
Step 3: Keep enough ventilation space between the POE Web Smart Ethernet Switch and the surrounding objects.
When choosing a location, please keep in mind the environmental restrictions discussed in Chapter
1, Section 4, Specification.
Step 4: Connect your Switch to network devices.
A. Connect one end of a standard network cable to the 10/100 RJ-45 ports on the front of the POE Web Smart Ethernet
Switch.
B. Connect the other end of the cable to the network devices such as printer servers, workstations or routers…etc.
Connection to the POE Web Smart Ethernet Switch requires UTP Category 5 or above cabling with
RJ-45 tips. For more information, please see the Cabling Specification in Appendix A.
Step 5: Supply power to the POE Web Smart Ethernet Switch.
A. Connect one end of the power cable to the POE Web Smart Ethernet Switch.
B. Connect the power plug of the power cable to a standard wall outlet then power on the POE Web Smart Ethernet
Switch.
When the POE Web Smart Ethernet Switch receives power, the Power LED should remain solid Green.
- 11 -

User’s Manual of FNSW-2400PS
2.3.2 Rack Mounting
To install the POE Web Smart Ethernet Switch in a 19-inch standard rack, follow the instructions described below.
Step 1: Place your POE Web Smart Ethernet Switch on a hard flat surface, with the front panel positioned towards your
front side.
Step 2: Attach a rack-mount bracket to each side of the POE Web Smart Ethernet Switch with supplied screws attached to
the package. Figure 2-3 shows how to attach brackets to one side of the POE Web Smart Ethernet Switch.
Figure 2-3 Attaching the brackets to the POE Web Smart Ethernet Switch
You must use the screws supplied with the mounting brackets. Damage caused to the parts by
using incorrect screws would invalidate your warranty.
Step 3: Secure the brackets tightly.
Step 4: Follow the same steps to attach the second bracket to the opposite side.
Step 5: After the brackets are attached to the POE Web Smart Ethernet Switch, use suitable screws to securely attach the
brackets to the rack, as shown in Figure 2-4.
- 12 -

User’s Manual of FNSW-2400PS
Figure 2-4 Mounting the POE Web Smart Ethernet Switch in a Rack
Step 6: Precede with the steps 4 and steps 5 of section 2.3.1 Desktop Installation to connect the network cabling and
supply power to your POE Web Smart Ethernet Switch.
- 13 -

User’s Manual of FNSW-2400PS
3. SWITCH MANAGEMENT
This chapter describes how to manage the POE Web Smart Ethernet Switch. Topics include:
- Overview
- Management method
- Logging on to the POE Web Smart Ethernet Switch
3.1 Overview
The POE Web Smart Ethernet Switch provides a user-friendly, Web interface. Using this interface, you can perform var-
ious switch configuration and management activities, including:
Please refer to the following Chapter 4 for the details.
3.2 Management Method
User can manage the POE Web Smart Ethernet Switch by Web Management via a network connection.
3.2.1 Web Management
The PLANET FNSW-2400PS provide a built-in browser interface. You can manage the Switch remotely by having a re-
mote host with Web browser, such as Microsoft Internet Explorer, Netscape Navigator or Mozilla Firefox.
The following shows how to startup the Web Management of the Switch, please note the Switch is configured through an
Ethernet connection, make sure the manager PC must be set on the same IP subnet address, for example, the default IP
address of the Switch is 192.168.0.100 (the factory-default IP address), then the manager PC should be set at
192.168.0.xxx (where x is a number between 1 and 254, except 100), and the default subnet mask is 255.255.255.0.
Use Internet Explorer 7.0 or above Web browser, enter default IP address http://192.168.0.100
After entering the username and password (default user name and password is “admin”) in login screen
Default IP : 192.168.0.100
Default Username: admin
Default Password: admin
- 14 -

User’s Manual of FNSW-2400PS
3.3 Logging on to the FNSW-2400PS
When you log on to the POE Web Smart Ethernet Switch Web interface for the first time, a sign-on string appears and you
are prompted for a Web login username and password. The factory default login username and password is admin.
Figure 3-1 POE Web Smart Ethernet Switch Web Login Screen
For security reason, please change and memorize the new password after this first setup.
- 15 -

User’s Manual of FNSW-2400PS
4. WEB MANAGEMENT
To modify your PC’s IP domain to the same with POE Web Smart Ethernet Switch then use the default IP address
(192.168.0.100) to remote configure POE Web Smart Ethernet Switch through the Web interface.
4.1 Login in to the Switch
To access the Web-browser interface you must first enter the user name and password, the default user name and
password is "admin”. You will see the following screen Figure 4-1 comes out on the Web browser program:
Figure 4-1 Web Login Screen
After the User name and Password is entered, you will see the Web Main Menu screen.
The Switch Menu provide seven major management functions, the screen in Figure 4-2 appears.
Fast Ethernet Port Link Status
Main Functions Menu
Figure 4-2 Web Main Menu Screen
M
a
in
Sc
r
ee
n
- 16 -

User’s Manual of FNSW-2400PS
The seven items and it description shown as below:
◆Administrator: Provide System configuration of POE Web Smart Switch. Explained in section 4.2.
◆Port Management: Provide Port Management configuration of POE Web Smart Switch. Explained in section 4.3.
◆VLAN Setting: Provide VLAN Setting configuration of POE Web Smart Switch. Explained in section 4.4.
◆QoS Setting: Provide QoS Setting configuration of POE Web Smart Switch. Explained in section 4.5.
◆Security: Provide Security Filter configuration of POE Web Smart Switch. Explained in section 4.6.
◆Spanning Tree: Provide Spanning Tree configuration of POE Web Smart Switch. Explained in section 4.7
◆Trunking: Provide Trunk Setting configuration of POE Web Smart Switch. Explained in section 4.8.
◆DHCP Relay Agent: Provide DHCP Relay Agent configuration of POE Web Smart Switch. Explained in section
4.9.
◆Backup/Recovery: Provide Backup/Recovery configuration of POE Web Smart Switch. Explained in section 4.10.
◆Miscellaneous: Provide Misc Operation configuration of POE Web Smart Switch. Explained in section 4.11.
◆SNMP Settings: Provide SNMP Settings configuration of POE Web Smart Switch. Explained in section 4.12.
◆Save Settings: Provide Save function of POE Web Smart Switch. Explained in section 4.13.
◆Logout: Provide Logout function of POE Web Smart Switch. Explained in section 4.14.
4.2 Administrator
This section provides System Information, IP Configuration, Password Setting, Factory Default, Firmware Update and
Reboot functions of POE Web Smart Ethernet Switch, the screen in Figure 4-3 appears and Table 4-1 describes the
System object of POE Web Smart Ethernet Switch.
Figure 4-3 System Web Page Screen
- 17 -

User’s Manual of FNSW-2400PS
O
Object Description
System Information Display the MAC address, and Software Version, Device Description. Explained in section
4.2.1.
IP Configuration Allow to change the IP subnet address of POE Web Smart Ethernet Switch. Explained in
section 4.2.2.
Password Setting Allow to change the username and password of POE Web Smart Ethernet Switch. Explained in
section 4.2.3.
Factory Default Allow reset the POE Web Smart Ethernet Switch to factory default mode. Explained in section
4.2.4.
Firmware Update Allow proceed firmware upgrade process of POE Web Smart Ethernet Switch. Explained in
section 4.2.5.
Reboot Allow reboot the POE Web Smart Ethernet Switch. Explained in section 4.2.6.
Table 4-1 Descriptions of the System Web Page Screen Objects
4.2.1 System Information
This section displays the MAC address and Software Version, also allow define the device description and press “Update”
button to take affect. The screen in Figure 4-4 appears.
Figure 4-4 System Information Web Page Screen
The page includes the following fields:
Object Description
•MAC Address Displays the unique hardware address assigned by manufacturer (default).
•Device Description Describes the Managed Switch. Up to 15 characters is allowed for the
Device Description.
•Software Version The software version of the switch.
•Idle Time Security Set idle time and behavior.
Table 4-2 Descriptions of the System Information Web Page Screen Objects
- 18 -

User’s Manual of FNSW-2400PS
4.2.2 IP Configuration
This section provides change the IP Address, Subnet Mask and Gateway, the screen in Figure 4-5 appears.
Figure 4-5 IP Configuration Web Page Screen
The page includes the following fields:
Object Description
IP Address
Assign the IP address that the network is using.
If DHCP client function is enabled, this switch is configured as a DHCP
client. The network DHCP server will assign the IP address to the switch
and display it in this column.
The default IP is 192.168.0.100 or the user has to assign an IP address
manually when DHCP Client is disabled.
Subnet Mask
Assign the subnet mask to the IP address.
If DHCP client function is disabled, the user has to assign the subnet
mask in this column field.
The default subnet mask is 255.255.255.0.
Gateway
Assign the network gateway for the switch.
If DHCP client function is disabled, the user has to assign the gateway in
this column field.
The default gateway is 192.168.0.254.
IP Configure
Select static IP address or DHCP client function
When DHCP function is enabled, the POE Web Smart Ethernet Switch
will be assigned an IP address from the network DHCP server. The de-
fault IP address will be replaced by the assigned IP address on DHCP
server. After the user clicks Apply, a popup dialog shows up to inform the
user that when the DHCP client is enabled, the current IP will lose and
user should find the new IP on the DHCP server.
Table 4-3 Descriptions of the IP Configuration Web Page Screen Objects
- 19 -

User’s Manual of FNSW-2400PS
4.2.3 Password Setting
This section provides change the Username and Password, the screen in Figure 4-6 appears.
Figure 4-6 Password Setting Web Page Screen
The page includes the following fields:
Object Description
Username Displays the user name.
Password
Confirm
Specifies the new password. The password is not displayed. As it entered
an “y” corresponding to each character is displayed in the field.
(The maximum length is 15 characters)
Confirms the new password. The password entered into second field
must be exactly the same as the password entered in the Password field.
Table 4-4 Descriptions of the Password Setting Web Page Screen Objects
4.2.4 Factory Default
This section provides reset the POE Web Smart Ethernet Switch to factory default mode, the screen in Figure 4-7 appears.
Figure 4-7 Factory Default Web Page Screen
- 20 -