Planet IGS-620TF User manual

Industrial 4-Port 10/100/1000BASE-T
+ 2-Slot 100/1000BASE-X SFP Ethernet Switch
IGS-620TF
User's Manual

Trademarks
Copyright © PLANET Technology Corp. 2015.
Contents are subject to revision without prior notice.
PLANET is a registered trademark of PLANET Technology Corp. All
other trademarks belong to their respective owners.
Disclaimer
PLANET Technology does not warrant that the hardware will work
properly in all environments and applications, and makes no warranty
and representation, either implied or expressed, with respect to
the quality, performance, merchantability, or tness for a particular
purpose.
PLANET has made every effort to ensure that this User’s Manual is
accurate; PLANET disclaims liability for any inaccuracies or omissions
that may have occurred.
Information in this User’s Manual is subject to change without notice
and does not represent a commitment on the part of PLANET. PLANET
assumes no responsibility for any inaccuracies that may be contained in
this User’s Manual. PLANET makes no commitment to update or keep
the current information in this User’s Manual, and reserves the right
to make improvements to this User’s Manual and/or to the products
described in this User’s Manual, at any time without notice.
If you nd information in this manual incorrect, misleading, or
incomplete, we would appreciate your comments and suggestions.
FCC Warning
This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to Part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against
harmful interference when the equipment is operated in a commercial
environment. This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accordance with
the Instruction manual, may cause harmful interference to radio
communications. Operation of this equipment in a residential area
is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.

CE Mark Warning
This is a Class A product. In a domestic environment, this product may
cause radio interference, in which case the user may be required to
take adequate measures.
WEEE Warning
To avoid the potential effects on the environment and human
health as a result of the presence of hazardous substances
in electrical and electronic equipment, end users of electrical
and electronic equipment should understand the meaning of
the crossed-out wheeled bin symbol. Do not dispose of WEEE as
unsorted municipal waste; they should be collected separately.
Revision
PLANET Industrial 4-port 10/100/1000BASE-T + 2-slot 100/1000BASE-X
SFP Ethernet Switch User's Manual
For Model: IGS-620TF
Revision: 1.1 (April, 2015)
Part No: EM-IGS_620TF_v1.1 (2350-AH0580-001)

Table of Contents
1. Introduction.............................................................................. 5
1.1 Package Contents ............................................................... 5
1.2 How to Use This Manual...................................................... 5
1.3 Product Features................................................................. 6
1.4 Product Specications ......................................................... 7
1.5 Physical Dimensions ............................................................ 9
2. Installation ..............................................................................10
2.1 Product Description ............................................................10
2.1.1 Switch Front Panel...................................................12
2.1.2 LED Indicators ........................................................13
2.1.3 Switch Upper Panel..................................................14
2.1.4 Wiring the Power Inputs...........................................15
2.1.5 Wiring the Fault Alarm Contact .................................16
2.1.6 Cabling...................................................................16
2.1.7 Redundancy Overview..............................................23
2.2 Mounting Installation..........................................................24
2.2.1 Installing DIN-rail Mounting......................................24
2.2.2 Wallmount Plate Mounting ........................................26
3. Applications .............................................................................27
4. Switch Operation......................................................................30
4.1 Address Table ....................................................................30
4.2 Learning ...........................................................................30
4.3 Forwarding & Filtering ........................................................30
4.4 Store-and-Forward .............................................................30
4.5 Auto-Negotiation................................................................31
5. Troubleshooting ........................................................................32
6. Cable Connection Parameters ....................................................33
APPENDIX A: Networking Connection...............................................34
A.1 Switch’s RJ45 Pin Assignments ............................................34
A.2 RJ45 Cable Pin Assignments................................................35

5
1. Introduction
1.1 Package Contents
Check the contents of your package for the following parts:
zIndustrial Gigabit Ethernet Switch x 1
zUser's Manual x 1
zDIN Rail Kit x 1
zWall Mount Kit x 1
If any of these are missing or damaged, please contact your dealer
immediately; if possible, retain the carton including the original packing
material, and use them again to repack the product in case there is a
need to return it to us for repair.
The term “Industrial Gigabit Ethernet Switch” mentioned in this
user’s manual also means the IGS-620TF.
1.2 How to Use This Manual
This Industrial Gigabit Ethernet Switch User Manual is
structured as follows:
Chapter 2 Installation
The chapter explains the feature, functionality and the physical
installation of the Industrial Gigabit Ethernet Switch.
Chapter 3 Application
The chapter explains the Industrial Gigabit Ethernet Switch application.
Chapter 4 Switch Operation
The chapter explains the Industrial Gigabit Ethernet Switch transmit
operation.
Chapter 5 Troubleshooting
The chapter explains the troubleshooting of the Industrial Gigabit
Ethernet Switch.
Chapter 6 Cable Connection Parameters
The chapter contains the cable connection parameters of the Industrial
Gigabit Ethernet Switch.

6
Appendix A
This chapter contains cable information of the Industrial Gigabit
Ethernet Switch.
1.3 Product Features
Physical Port
4-Port 10/100/1000BASE-T RJ45 with auto MDI / MDI-X function
2 SFP interfaces, 100/1000BASE-X dual mode (DIP switch control)
Layer 2 Features
IEEE 802.3 / 802.3u / 802.3ab / 802.3z Ethernet Standard
Compliant
Supports Auto-negotiation and 10/100Mbps half / full duplex and
1000Mbps full duplex mode
 High performance Store and Forward architecture, runt/CRC ltering
eliminates erroneous packets to optimize the network bandwidth
Prevents packet loss with back pressure (half-duplex) and IEEE
802.3x PAUSE frame ow control (full-duplex)
9K Jumbo Frame Size support
Backplane (Switching Fabric): 12Gbps
Integrated address look-up engine, support 1K absolute MAC
addresses
Automatic address learning and address aging
CSMA/CD Protocol
Industrial Case / Installation
Slim IP30 metal case / protection
DIN rail and wall mount design
Redundant Power Design
- 12 to 48V DC, redundant power with polarity reverse protect function
- AC 24V power adapter acceptable
Supports EFT protection for 6000 VDC for power line
Supports 6000 VDC Ethernet ESD protection
-40 to 75 degrees C operating temperature

7
Fiber Port Redundancy
Link status auto-detect and redundant on dual ports with the same
connector type
Only when primary port is active, the backup port is blocked.
 When primary port link fails, the trafc will swap to backup port
automatically.
 Once the primary port status is back to link up, the trafc swaps
from backup port to primary port.
1.4 ProductSpecications
Model IGS-620TF
Hardware Specications
10/100/1000BASE-T
Ports 4
SFP Interfaces
2 1000BASE-SX/LX/BX SFP interfaces
(Port-5 and Port-6)
Compatible with 100BASE-FX SFP
Dimensions
(W x D x H) 135 x 87 x 32mm
Weight 503g
Power Requirements
DC 12~48V, Redundant power with polarity
reverses protection function. AC 24V Power
Adapter
Power Consumption
/ Dissipation 7.2 watts/24BTU
Installation DIN rail kit and wall mount ear
Switch Specications
Switch Processing
Scheme Store-and-Forward
MAC Address Table 1K entries
Flow Control Back pressure for half duplex
IEEE 802.3x pause frame for full duplex
Switch Fabric 12Gbps

8
Throughput
(packet per second) 8.9Mpps
Maximum
Transmission Unit 9216bytes
Network Cables
10/100/1000BASE-T :
Cat. 3, 4, 5, 5e, 6 UTP cable (100meters, max.)
EIA/TIA-568 100-ohm STP (100meters, max.)
1000BASE-SX :
50/125μm or 62.5/125μm multi-mode ber
optic cable, up to 550m/2km (vary on SFP
module)
1000BASE-LX :
9/125μm single-mode ber optic cable, up to
10/20/30/40/50/70/120 kilometers (vary on
SFP module)
100BASE-FX :
50/125μm or 62.5/125μm multi-mode ber
optic cable, up to 2 kilometers (vary on SFP
module)
9/125μm single-mode ber optic cable, up to
20/40/60/120 kilometers (vary on SFP module)
Standards Conformance
Standards
Compliance
IEEE 802.3 Ethernet
IEEE 802.3u Fast Ethernet
IEEE 802.3ab Gigabit Ethernet
IEEE 802.3z Gigabit Ethernet
IEEE 802.3x Full-Duplex Flow Control
Regulation
Compliance FCC Part 15 Class A, CE
Stability Testing
IEC60068-2-32 (free fall)
IEC60068-2-27 (shock)
IEC60068-2-6 (vibration)
Environment
Temperature Operating: -40~75 degrees C
Storage: -40~75 degrees C
Humidity Operating: 5~95% (non-condensing)
Storage: 5~95% (non-condensing)

9
1.5 Physical Dimensions
IGS-620TF Industrial Gigabit Ethernet Switch dimensions (W x D x H):
135 x 87 x 32mm
Side View
Bottom View
Front View
Mounting Kit Mounting Kit
DIN-Rail Kit
Top View Rear View
6
LNK/
ACT
SFP
1000X 1000X
P1 P2 FAULT
5
4 3 2 1
IGS-620TF
1000 LNK/ACT 100 LNK/ACT
LNK/
ACT
SFP
Input DC 12~48V, AC 24V
V1-
V1+
V2-
V2+
PWR1
Port 5
Port 6
Mode
Fault
PWR2
100FX
100FX
Redundant
1000X
ON OFF
1000X
Switch
Port 5
Port 6
Fiber Mode
1 2 3
ON
1 2 3 4 5 6

10
2. Installation
This section describes the functionalities of the Industrial Gigabit
Ethernet Switch’s components and guides how to install it on the
desktop. Basic knowledge of networking is assumed. Please read this
chapter completely before continuing.
2.1 Product Description
Flexibility and Network Distance Extension Solution
The IGS-620TF Industrial Gigabit Ethernet Switch is equipped with
four 10/100/1000BASE-T auto-negotiation ports and two 100/1000X
SFP slots. The two SFP slots are compatible with 1000BASE-SX / LX
or 100BASE-FX through SFP (Small Form Factor Pluggable) ber-optic
transceiver; the two SFP slots allow changing the operation speed
mode with its built-in DIP switch. The ber optical uplink capability
guarantees the throughput to all nodes hooked into the network and
the Gigabit Ethernet distance can be extended from 550m/2km (Multi-
Mode ber cable) up to 10/20/30/40/50/70/120 kilometers (Single-
Mode ber cable). The Fast Ethernet distance can also be extended
from 2km (Multi-Mode ber cable) up to 20/40/60/120 kilometers
(Single-Mode ber cable). They are well suited for applications within
the factory data centers and distributions.
Adjustable 6-Port Switch Mode or 4 + 2 Fiber Redundant Mode
Via the built-in DIP switch, the IGS-620TF can be congured as 6-Port
Ethernet switch or 4+2 ber redundant mode. With the 6-Port switch
mode, the IGS-620TF can operate in Store-and-Forward mechanism
with high performance; on the other hand, when in the 4+2 ber
redundant mode, it provides rapid ber redundancy of link for highly
critical Ethernet applications. The redundant mode also supports auto-
recovering function. If the destination port of a packet is link down, it
will forward the packet to the other port of the backup pair.
Environmentally Hardened Design
With IP30 metal industrial case protection, the IGS-620TF provides a
high level of immunity against electromagnetic interference and heavy
electrical surges which are usually found on plant oors or in curb side